Nissan has released our original HEV system in Japan on November 2010, and will release it in US market on March 2011. The 1 motor 2 clutch parallel type using conventional 7 speed automatic transmission has been employed without torque converter and with a manganese cathode and laminated type Li-ion Battery. This system is well recognized its higher efficiency but lower weight and cost, however, has never realized due to technical difficulties of smoothness. At this session, performance achievements and hinged breakthrough technologies will be presented. Presenter Tetsuya Takahashi, Nissan Motor Co., Ltd.
A newly developed OHC (Over-Head Camshaft) prototype of a six-cylinder in-line diesel engine (with bore size: 114mm, stroke size: 130mm) was studied, comparing with the previous version of OHV (Over-Head Valve) type engine (with bore size: 110mm, stroke size: 130mm). It was found that the new type of cylinder block (with 130.8 kg of mass) has significantly lower natural frequencies than those for the previous type of cylinder block (with 133.2 kg of mass). Furthermore, slightly more predominant engine noise and vibration were induced in the new engine. The vibration behavior and the excitation force transmission characteristics were investigated by EMA (Experimental Modal Analysis). We performed a series of impact tests for (1) free-free cylinder block, (2) free-free crankshaft substructure with torsional damper and flywheel attached, and (3) the case where (1) and (2) are assembled together.
A flow analysis method with quick turnaround time has been studied for application to flows in the engine compartment of vehicles. In this research, a rapid modeling method based on the Cartesian mesh system was developed to obtain flow field information quickly. With this modeling method, the original shape is approximated by many small cubic cells, allowing automatic mesh generation in significantly less time. Moreover, a hierarchical mesh system that reduces the total number of meshes has been introduced. This multi-level mesh system is also highly capable of representing shapes in detail. Another important issue in flow calculations in the engine bay is the treatment of the boundary conditions such as the radiator and cooling fan. With the proposed method, the fluid dynamics characteristics of such components are measured, and characteristics such as the pressure loss/gain and the rotational vector of the fan are reflected in the flow field as empirical models.
This paper describes the method used to design the basic control algorithm of a lane-keeping support system that is intended to assist the driver's steering action. Lane-keeping control has been designed with steering torque as the control input without providing a minor loop for the steering angle. This approach was taken in order to achieve an optimum balance of lane-keeping control, ease of steering intervention by the driver and robustness. The servo control system was designed on the basis of H2 control theory. Robustness against disturbances, vehicle nonlinearity and parameter variation was confirmed by μ - analysis. The results of computer simulations and driving tests have confirmed that the control system designed with this method provides the intended performance.
It was found that pitting resistance of gears is strongly influenced by resistance to temper softening of carburized steel. The investigation about the influence of chemical compositions on hardness after tempering revealed that silicon, chromium and molybdenum are effective elements to improve resistance to temper softening and pitting resistance. Considering the production of gears, molybdenum is unfavorable because it increases hardness of normalized or annealed condition. Developed new steel contains about 0.5 mass% of silicon and 2.7 mass% chromium. The new steel has excellent pitting resistance and wear resistance. Fatigue and impact strength are equivalent to conventional carburized steels. Cold-formability and machinability of the new steel are adequate for manufacturing gears because of its ordinary hardness before carburizing. The new steel has already been put to practical use in automatic transmission gears. Application test results are also reported.
An Adaptive Cruise Control system with stop-and-go capability has been developed to reduce the driver's workload in traffic jams on expressways. Based on an analysis of driving behavior characteristics in expressway traffic jams, a control system capable of modeling those characteristics accurately has been constructed to provide natural vehicle behavior in low-speed driving. The effectiveness of the system was evaluated with an experimental vehicle, and the results confirmed that it reduces the driver's workload. This paper presents an outline of the system and its effectiveness along with the experimental results.
This paper describes an image processing system for tracking a traffic lane by recognizing white lines on the road ahead. The system utilizes the features of the white lines and the Hough transformation to detect white line candidate points in images taken with a CCD camera. The parameters of the road configuration and vehicle attitude are estimated with an extended Kalman filter. This system has been applied to achieve a lane-keeping assistance system that provides steering control based on the host vehicle’s lateral position in its lane.
The International Lubricant Standardization and Approval Committee (ILSAC) ATF subcommittee members have compared the two oxidation bench test methods, Aluminum Beaker Oxidation Test (ABOT) and Indiana Stirring Oxidation Stability Test (ISOT), using a number of factory-fill and service-fill ATFs obtained in Japan and in the US. In many cases, the ATFs were more severely oxidized after the ABOT procedure than after the same duration of the ISOT procedure. The relative severity of these two tests was influenced by the composition of the ATFs. The bench test oxidation data were compared with the transmission and the vehicle oxidation test data.
An approach to designing an intelligent vehicle controller for partially supporting driver operation of a vehicle is proposed. Vehicle behavior is regarded as a system performed by the interaction between the driving environment, vehicle as a machine and driver expectations for the vehicle movements. Driver intention to accelerate or decelerate is mainly generated by the perception of the driving environment. The model we propose involves information on the driving environment affecting driver intention taking driver differences in perceiving the driving environment into account. An engineering model for installing the vehicle controller is expressed by a multipurpose decision-maker allowing explicit treatment of the driving environment, vehicle action, and driver intention. A reasoning engine deals with differences in individual driver traits for generating intention to decelerate by using fuzzy integrals and fuzzy measures.
Every fuel injection system for DI gasoline engines has a DC-DC converter to provide high, stabile voltage for opening the injector valve more quickly. A current control circuit for holding the valve open is also needed, as well as a large-capacity capacitor for pilot injection. Since these components occupy considerable space, an injector drive unit separate from the ECU must be used. Thus, there has been a need for a fuel injection system that can inject a small volume of fuel without requiring high voltage. To meet that need, we have developed a dual coil injector and an opening coil current control system. An investigation was also made of all the factors related to the dynamic range of the injector, including static flow rate, fuel pressure, battery voltage and harness resistance. Both efforts have led to the adoption of a battery voltage-driven fuel injector.
The separation of combustion noise and mechanical noise from the total noise of a four-cylinder in-line diesel engine at idling was carried out with high accuracy by changing the fuel injection timing. The mechanical noise, which accounts for the major share at 93%, was then separated into noises from the typical mechanical causes, and the valve train was found to be the major noise source. From analysis of the noise generating mechanism for the valve train, it was clarified that the noise was caused mainly by the gear rattling owing to the variation in the camshaft drive torque.
To investigate the future direction of diesel emission control technologies and fuel technologies, exhaust emissions tests of diesel vehicles/engines with advanced after-treatments such as NSR catalyst, CR-DPF, and Urea-SCR or a combination of these, were conducted using various fuels, and fuel sulfur effect on performance of the after-treatments after mileage accumulation was also evaluated in step II study of JCAP Diesel WG. Overall results shows that the after-treatments have significant effects on reducing emission and reducing fuel sulfur have significant effects on function of the after-treatments in term of decrease of sulfate and SOF, and less deterioration of function of after-treatments after mileage accumulation.
One important development area for obtaining better fuel economy is to reduce mechanical friction losses in engine components. The valvetrain is a significant source of mechanical friction loss in an automobile engine, especially at low speeds where fuel economy is most important. This paper describes the potential use of diamond-like carbon (DLC) coatings at the cam/follower interface in a bucket-type valvetrain. Using a pin-on-disk tester, a motored valvetrain friction apparatus and a bench test rig, the frictional performance of DLC coatings was tested. Experimental data indicate that under a lubricated condition, DLC coatings produced by a plasma CVD (chemical vapor deposition) technique did not show a sufficient effect on reducing friction (only a 20-25% reduction) contrary to our expectations. DLC coatings prepared by arc-ion plating and containing less hydrogen showed superior frictional performance compared with CVD-DLC coatings under a lubricated condition.
A human body model has been developed for conducting personal computer simulations to evaluate physical work loads, especially muscle loads, associated with the driving position and arm and leg motions. The validity of the model was confirmed by comparing estimated work loads with electromyographic measurements. Correlation analyses were conducted to examine the relationship between the estimated loads and subjective evaluations. The results indicated the regions of the body where loads had the largest impact on the perceived sensation of physical effort and were used to derive an index for evaluating the overall work load of the entire body. The simulation method was used to evaluate control switch positions, driving position and vehicle entry/exit motions.
The geometry and area of the notch in the swirl control valve installed in the intake port were varied to analyze the effects on HC emissions. A swirl control valve functions to promote the formation of a homogeneous mixture, enabling the amount of liquid fuel supplied to the cylinder to be reduced. For this reason, it is difficult to obtain an added effect through the combined use of a swirl control valve and an auxiliary-air type of injector for assisting fuel atomization. Tumble (vertical swirl) flow fields are effective in shortening the combustion period. This results in a higher exhaust gas temperature at an equivalent level of combustion stability. It was thought that swirl flow fields produce residual gas flow in the cylinder after the completion of the main combustion period. It is surmised that the residual gas flow functions to diffuse and promote after-burning of the unburned HC layer.
Flow measurement by laser Doppler velocimetry and visualization of in-cylinder fuel vapor motion by laser induced fluorescence were performed for various types of intake systems that generated several different combinations of swirl and tumble ratios. The measured results indicate that certain swirl and tumble ratios are needed to achieve charge stratification in the cylinder. Performance tests were also carried out to determine the combustion characteristics of each intake system. Then, the features of combustion when the charge stratification was realized was analyzed.
This paper presents a new electronic torque split four-wheel-drive system called All-Mode 4WD, which has been adopted in the latest generation of sport-utility vehicles (SUVs). As a torque split system designed specifically for SUV use, it provides stable driving performance matching the driver's intentions under all sorts of operating conditions, from a completely natural on-road driving feel to powerful traction for off-road travel.
A new concept for diesel combustion was investigated by means of numerical simulation, engine experiment, and combustion observation in order to realize a simultaneous reduction of NOx and particulate emission. This concept (HiMICS: Homogeneous charge intelligent Multiple Injection Combustion System) is based on pre-mixed compression ignition combustion combined with multiple injection. Combustion characteristics of HiMICS concept was investigated by comparing with both a standard single injection and a pilot injection. In HiMICS concept, the pre-mixture is formed by a preliminary injection performed during a period from the early stage of the induction stroke to the middle stage of the compression stroke. Modified KIVA-II code was used to predict engine performances and emissions of each injection method. The simulation results show a capability of considerable improvement in the trade-off relation between NOx emissions and fuel consumption of HiMICS.
Hino has developed new J-series medium-duty diesel engines for trucks and buses. The new J-series comprises four, five and six-cylinder engines with the same cylinder bore and stroke and with both naturally aspirated and charge air cooled. Both output and torque have been enhanced along with fuel efficiency in an engine that is lighter and more compact than ever and reaches new heights of durability and reliability. J-series engine features a 4-valve system and OHC valve train design, which achieved an uniform combustion by a centered nozzle and combustion chamber design. This decreases the maximum combustion temperature and hence improved the NOx,smoke and PM emissions. And a reduced pumping loss results in improving the fuel consumption. J-series engines thus meet the Japanese 1994 emission regulations. Another feature is a fully electronically controlled common-rail fuel injection system, which is equipped in a specified engine of naturally aspirated 6 cylinder.