Search Results

This paper presents an evaluation of two different Vehicle to Infrastructure (V2I) applications, namely Red Light Violation Warning (RLVW) and Green Light Optimized Speed Advisory (GLOSA). The evaluation method is to first develop and use Hardware-in-the-Loop (HIL) simulator testing, followed by extension of the HIL testing to road testing using an experimental connected vehicle. The HIL simulator used in the testing is a state-of-the-art simulator that consists of the same hardware like the road side unit and traffic cabinet as is used in real intersections and allows testing of numerous different traffic and intersection geometry and timing scenarios realistically. First, the RLVW V2I algorithm is tested in the HIL simulator and then implemented in an On-Board-Unit (OBU) in our experimental vehicle and tested at real world intersections.

Combined active and passive damping is a recent trend that can be an effective solution to challenging NVH problems, especially for lightweight vehicle components that demand advanced noise and vibration treatments. Compact patches are of particular interest due to their small size and cost, however, improved modeling techniques are needed at the design stage for such methods. This paper presents a refined modeling procedure for side-by-side active and passive damping patches applied to thin, plate-like, powertrain casing structures. As an example, a plate with fixed boundaries is modeled as this is representative of real-life transmission covers which often require damping treatments. The proposed model is then utilized to examine several cases of active and passive patch location, and vibration reduction is determined in terms of insertion loss for each case.

The effect of aerodynamically induced pre-swirl on the acoustic and performance characteristics of an automotive centrifugal compressor is studied experimentally on a steady-flow turbocharger facility. Accompanying flow separation, broadband noise is generated as the flow rate of the compressor is reduced and the incidence angle of the flow relative to the leading edge of the inducer blades increases. By incorporating an air jet upstream of the inducer, a tangential (swirl) component of velocity is added to the incoming flow, which improves the incidence angle particularly at low to mid-flow rates. Experimental data for a configuration with a swirl jet is then compared to a baseline with no swirl. The induced jet is shown to improve the surge line over the baseline configuration at all rotational speeds examined, while restricting the maximum flow rate. At high flow rates, the swirl jet increases the compressor inlet noise levels over a wide frequency range.

In recent years, the trend in the automotive industry has been favoring the reduction of fuel consumption in vehicles with the help of new and emerging technologies, such as Vehicle to Infrastructure (V2I), Vehicle to Vehicle (V2V) and Vehicle to Everything (V2X) communication and automated driving capability. As the world of transportation gets more and more connected through these technologies, the need to implement algorithms with V2I capability is amplified. In this paper, an algorithm called Pass at Green, utilizing V2I and vehicle longitudinal automation to modify the speed profile of a mid-size generic vehicle to decrease fuel consumption has been studied. Pass at Green (PaG) uses Signal Phase and Timing (SPaT) information acquired from upcoming traffic lights, which are the current phase of the upcoming traffic light and remaining time that the phase stays active.

An appropriate fault diagnosis and Isolation (FDI) strategy is very useful to prevent system failure. In this paper, a model-based fault diagnosis strategy is developed for an internal combustion engine (ICE) under speed control. Engine throttle fault and the manifold pressure sensor fault are detected and isolated. A nonlinear observer based residual generation approach is proposed. Manifold pressure and throttle are observed. Fault codes are designed with redundancy to prevent bit error. Performance of fault diagnosis strategy has been evaluated with simulations.

This research focuses on the development and performance of analytical models to simulate a tractor-semitrailer in straight-ahead braking. The simulations were modified and tuned to simulate full-treadle braking with all brakes functioning correctly, as well as the behavior of the tractor-semitrailer rig under full braking with selected brakes disabled. The models were constructed in TruckSim and based on a tractor-semitrailer used in dry braking performance testing. The full-scale vehicle braking research was designed to define limits for engineering estimates on stopping distance when Class 8 air-braked vehicles experience partial degradation of the foundation brake system. In the full scale testing, stops were conducted from 30 mph and 60 mph, with the combination loaded to 80,000 lbs (gross combined weight or GCW), half payload, and with the tractor-semitrailer unladen (lightly loaded vehicle weight, or LLVW).

The Federal Side Impact Test Procedure prescribed by FMVSS 214, simulates a central, orthogonal intersection collision between two moving vehicles by impacting the side of the stationary test vehicle with a moving test buck in a crabbed configuration. While the pre- and post-impact speeds of the vehicles involved in an accident can not be duplicated using this method, closing speeds, vehicle damage, vehicle speed changes and vehicle accelerations can be duplicated. These are the important parameters for the examination of vehicle restraint system performance and the prediction of occupant injury. The acceptability of this method of testing is not as obvious for the reconstruction of accidents where the impact is non-central, or the angle of impact is not orthogonal. This paper will examine the use of crash testing with a single moving vehicle to simulate oblique or non-central collisions between two moving vehicles.

The capabilities of the servo press for varying the ram speed during stroke and for adjusting the stroke length are well known. Various companies installed servo presses for blanking. Some of the considerations may include increase in productivity and flexibility in adjusting the ram stroke, noise reduction and improvement of edge quality of blanked edge. The objectives of this study are to determine the effect of ram (blanking) speed upon the edge quality, and the effect of multiple step blanking using several punch motions, during one blanking stroke.

Experimentally derived brain response envelopes are needed to evaluate and validate existing finite element (FE) head models. Motion of the brain relative to the skull during rotational input was measured using high-speed biplane x-ray. To generate repeatable, reproducible, and scalable data, methods were developed to reduce experimental variance. An “extreme-energy” device was developed to provide a controlled input that is unaffected by specimen characteristics. Additionally, a stereotactic frame was used to deploy radiopaque markers at specific, pre-determined locations within the brain. One post-mortem human surrogate (PMHS) head specimen was subjected to repeat tests of a half-sine rotational speed pulse in the sagittal plane. The desired pulse had a peak angular speed of 40 rad/s and duration of 30 ms. Relative motion of the brain was quantified using radiopaque targets and high-speed biplane x-ray. Frontal and occipital intracranial pressure (ICP) were also measured.

This paper presents some of the technical considerations that underlie the development of the master plan and the establishment of design specifications for Ohio's Highway Research Laboratory. It describes the overall features of the master plan and discusses some of the critical design features as these relate to the various tracks and other field facilities. The development of the master plan was guided by a study of the layout of existing proving grounds and by the experience gained over the years in their operations. It was guided furthermore by a set of principles relating to operational considerations, considerations of flexibility in the layout, land utilization, safety, capacity, and cost. Finally, it was guided by an indication of future research and development needs as expressed by researchers and potential sponsors in both government and industry.

Testing vision-based advanced driver assistance systems (ADAS) in a Camera-in-the-Loop (CiL) bench setup, where external visual inputs are used to stimulate the system, provides an opportunity to experiment with a wide variety of test scenarios, different types of vehicle actors, vulnerable road users, and weather conditions that may be difficult to replicate in the real world. In addition, once the CiL bench is setup and operating, experiments can be performed in less time when compared to track testing alternatives. In order to better quantify normal operating zones, track testing results were used to identify behavior corridors via a statistical methodology. After determining normal operational variability via track testing of baseline stationary surrogate vehicle and pedestrian scenarios, these operating zones were applied to screen-based testing in a CiL test setup to determine particularly challenging scenarios which might benefit from replication in a track testing environment.

This paper describes the modeling, controller development, and implementation of a transmission clutch pressure control system. A nonlinear analytical model for the clutch pressure control system is developed and implemented using Matlab/Simulink, and validated by experimental data. The dominant dynamics are identified via model analysis, and a linear model is derived for controller design. Openloop (feedforward) and closed loop (feedback) pressure control strategies are designed and implemented in a test setup. Experimental results show that the combined feedforward and feedback control gives superior performance as compared to feedforward control alone.

As vehicle emissions regulations become increasingly stringent, there is a growing need to accurately model aftertreatment systems to aid in the development of ultra-low NOx vehicles. Common solutions to this problem include the development of complex chemical models or expansive neural networks. This paper aims to present the development process of a simpler Selective Catalytic Reduction (SCR) conversion efficiency Simulink model for the purposes of modeling tail pipe NOx emission levels based on various inputs, temperature shifts and SCR locations, arrangements and/or sizes in the system. The main objective is to utilize this model to predict tail pipe NOx emissions of the EPA Federal Test Procedures for heavy-duty vehicles. The model presented within is focused exclusively on heavy-duty application compression ignition engines and their corresponding aftertreatment setups.

A time-efficient throttle flow data collection method is described. It uses a sonic nozzle flow bench to measure air flow as a function of throttle angle and pressure in a manner analogous to on-engine dynamometer throttle flow characterization. Opening each sonic nozzle combination, then recording throttle downstream pressure and computed nozzle flow allows data to be taken in a fraction of the time normally needed. Throttle flow modeling considerations are then discussed.

The current work demonstrates effective suppression of compression system surge instabilities by installing a variable cross-sectional flow area restriction within the inlet duct of a turbocharger centrifugal compressor operating on a bench-top facility. This restriction couples with the compressor, similar to stages in a multi-stage turbomachine, where the effective pressure ratio is the product of those for the restriction and compressor. During experiments at constant compressor rotational speed, the compressor is stable over the negatively sloped portion of the pressure ratio vs. flow rate characteristics, so the restriction is eliminated within this operating region to preserve compressor performance. At low flow rates, the slope of the compressor alone characteristics reaches a positive value, and the unrestricted compression system enters mild surge. Further reduction of flow rate with the unrestricted compressor inlet results in a sudden transition to deep surge instabilities.

A machine has been developed to measure the complete inertia matrix; mass, center of gravity (CG) location, and all moments and products of inertia. Among other things these quantities are useful in studying engine vibrations, calculation of the torque roll axis, and in the placement of engine mounts. While the machine was developed primarily for engines it can be used for other objects of similar size and weight, and even smaller objects such as tires and wheels/rims. A key feature of the device is that the object, once placed on the test table, is never reoriented during the test cycle. This reduces the testing time to an hour or less, with the setup time being a few minutes to a few hours depending on the complexity of the shape of the object. Other inertia test methods can require up to five reorientations, separate CG measurement, and up to several days for a complete test.

Road Departure Mitigation System (RDMS) is a new feature in vehicle active safety systems. It may not rely only on the lane marking for road edge detection, but other roadside objects This paper discusses the radar aspect of the RDMS testing on roads with grass road edges. Since the grass color may be different at different test sites and in different seasons, testing of RDMS with real grass road edge has the repeatability issue over time and locations. A solution is to develop surrogate grass that has the same characteristics of the representative real grass. Radar can be used in RDMS to identify road edges. The surrogate grass should be similar to representative real grass in color, LIDAR characteristics, and Radar characteristics. This paper provides the 24 GHz and 77 GHz radar characteristic specifications of surrogate grass.

In this paper, a series of design, development, and implementation details for testing and evaluation of Lane Departure Warning and Prevention systems are being discussed. The approach taken to generate a set of repeatable and relevant test scenarios and to formulate the test procedures to ensure the fidelity of the collected data includes initial statistical analysis of applicable statistics; growth and probabilistic pruning of a test matrix; simulation studies to support procedure design; and vehicle instrumentation for data collection. The success of this comprehensive approach strongly suggests that the steps illustrated in this paper can serve as guidelines towards a more general class of vehicular safety and advanced driver assistance systems evaluation.

Sled testing procedures should reflect a rigorous level of repeatability across trials and reproducibility across testing facilities. Currently, different testing facilities use various methods to set the harness tension for child restraint system (CRS) sled tests. The objective of this study is to identify which harness tightening procedure(s) produce tensions within a reasonable target range while showing adequate reproducibility, repeatability, and ease-of-use. Five harness tightening procedures were selected: A) FMVSS 213 procedure, B) a 3-prong tension gauge, C) ECE R44/R129 procedure, D) two finger method, and E) pinch test. Two CRS models were instrumented with a tension load cell in the harness system. Seven sled room operators were recruited to perform each of the five harness tightening procedures for ten repetitions apiece on both instrumented CRS using a Hybrid III 3-year-old.

Low speed autonomous shuttles emulating SAE Level L4 automated driving using human driver assisted autonomy have been operating in geo-fenced areas in several cities in the US and the rest of the world. These autonomous vehicles (AV) are operated by small to mid-sized technology companies that do not have the resources of automotive OEMs for carrying out exhaustive, comprehensive testing of their AV technology solutions before public road deployment. Due to the low speed of operation and hence not operating on roads containing highways, the base vehicles of these AV shuttles are not required to go through rigorous certification tests. The way these vehicles’ driver assisted AV technology is tested and allowed for public road deployment is continuously evolving but is not standardized and shows differences between the different states where these vehicles operate.