Search Results

Green Light Optimized Speed Advisory (GLOSA) systems have the objective of providing a recommended speed to arrive at a traffic signal during the green phase of the cycle. GLOSA has been shown to decrease travel time, fuel consumption, and carbon emissions; simultaneously, it has been demonstrated to increase driver and passenger comfort. Few studies have been conducted using historical cycle-by-cycle phase probabilities to assess the performance of a speed advisory capable of recommending a speed for various traffic signal operating modes (fixed-time, semi-actuated, and fully-actuated). In this study, a GLOSA system based on phase probability is proposed. The probability is calculated prior to each trip from a previous week’s, same time-of-day (TOD) and day-of-week (DOW) period, traffic signal controller high-resolution event data.

The following computational study examines the structure of sonic hydrogen jets using inlet conditions similar to those encountered in direct-injection hydrogen engines. Cases utilizing the same mass and momentum flux while varying exit-to-chamber pressure ratios have been investigated in a constant-volume computational domain. Furthermore, subsonic versus sonic structures have been compared using both hydrogen and ethylene fuel jets. Finally, the accuracy of scaling arguments to characterize an underexpanded jet by a subsonic “equivalent jet” has been assessed. It is shown that far downstream of the expansion region, the overall jet structure conforms to expectations for self-similarity in the far-field of subsonic jets. In the near-field, variations in fuel inlet-to-chamber pressure ratios are shown to influence the mixing properties of sonic hydrogen jets. In general, higher pressure ratios result in longer shock barrel length, though numerical resolution requirements increase.

The oxidation of 1-butene and n-butane in air at elevated pressure was investigated in a high pressure chemical flow reactor. Results are presented for pressures of 3, 6, and 10 atm, temperatures near 900K, and lean equivalence ratio. Gas samples were analyzed using gas chromatography with aldehydes sampled using a dinitrophenylhydrazine/acetonitrile procedure employing gas chromatography/mass spectrometry analysis. Major common products observed include CO, CH2O, C2H4, C3H6, and CO2. Additional major products included 1,3-C4H6 for 1-butene and 1-C4H8 for n-butane. Fuel conversion was increased with increased pressure, temperature, and equivalence ratio with 1-butene more reactive than n-butane. Large levels of lower molecular weight carbonyls resulted from 1-butene whereas significant amounts of conjugate and lower molecular weight alkenes resulted from n-butane. Trends in product distributions with increasing pressure were successfully accounted for by current autoignition theories.

This paper provides a comparison of wall heat fluxes and quenching distances as one-dimensional hydrogen and heptane flames impinge head-on onto a wall. It is shown that the quenching distances for stoichiometric H2/air and C7H16/air flames under the specified conditions of this study are about the same, but the wall heat flux for the H2/air flames is approximately a factor of two greater. For lean H2/air mixtures, the quenching distance increases substantially and the wall heat flux decreases. To understand more clearly the interplay of flame speed, temperature, thermal diffusivity, and surface kinetics on the results, studies of H2/O2 flames are also carried out.

A new gas phase kinetic model using Westbrook's gas phase n-heptane model and Frenklach's soot model was constructed. This model was then used to predict the impact on PAH formation as an indices of soot formation on ethanol/diesel fuel blends. The results were then compared to soot levels measured by various researchers. The ignition delay characteristics of ethanol were validated against experimental results in the literature. In this paper the results of the model and the comparison with experimental results will be discussed along with implications on the method of incorporation of additives and alternative fuels.

The diesel particulate filter (DPF), in conjunction with fuel reformulation technologies such as ultralow sulfur fuel or Fischer-Tropsch diesel, represents a promising solution for reducing particulate emissions. In this work, membrane-coated and conventional uncoated SiC diesel particulate filters were tested on a 4-cylinder Volkswagen TDI diesel engine under four different engine load conditions at constant engine speed. Di-tert-butyl-sulfide was added to the base fuel to increase the sulfur content from 39 ppm to approximately 300 PPM. Gaseous and particulate mass emission measurements, as well as, PM morphology and composition have been used to address how engine-out and post-DPF emissions and post-oxidation catalyst emissions change with increasing fuel sulfur content. The influence of fuel sulfur on emissions was compared for the membrane coated and uncoated SiC filter using the same diesel oxidation catalyst (DOC) located downstream of the DPF.

Models for the components of a long-duration UAV power system are set forth. The models include the solar array, solar array power converter, fuel cell and electrolyzer system and corresponding power converter, and propulsion load. Based on these models, a power management control is derived, which when coupled with the component models, are used to simulate power system performance during start-up, through a day-night cycle, and through a solar eclipse.

In Diesel engines, the vapor phase of the fuel jet is known to impinge on the walls. This impingement is likely to have an effect on mixing characteristics, the structure of the diffusion flame and on pollutant formation and oxidation. These effects have not been studied in detail in the literature. In this work, the structure of a laminar wall jet that is generated from the impingement of a free laminar jet on a wall is discussed. We study the laminar jet with the belief that the local structure of the reaction zone in the turbulent reacting jet is that of a laminar flame. Results from non-reacting and reacting jets will be presented. In the case of the non-reacting jets, the focus of the inquiry is on assessing the accuracy of the computed results by comparing them with analytical results. Velocity profiles in the wall jet, growth rates of the half-width of the jet and penetration rates are presented.

The 2002 Pennsylvania State University FutureTruck Team has converted a stock 2002 Ford Explorer sport utility vehicle into a post-transmission, pre-transfer case parallel hybrid electric vehicle, dubbed the Wattmuncher. The stock 4.0L, V-6 spark ignition engine was replaced with a more efficient 2.5L direct-injection, common-rail, turbocharged diesel engine that meets Euro 3 emission standards. A diesel particulate filter was implemented for additional emission reductions. ADVISOR simulation results predict 23.5 mpg city and 31.9 mpg highway fuel economy while maintaining stock acceleration and towing capacity. The vehicle was designed for manufacturability, and a complete cost analysis for mass production results in an expected $4,050 added cost for this hybridized Explorer.

With the need for improvement in the fuel economy along with reduction in emissions due to stringent regulations, powertrain hybridization has become the focal point of research for the automotive sector. Hydraulic hybrids have progressively gained acceptance due to their high power density and low component costs relative to their electric counterpart and many different architectures have been proposed and implemented on both on and off-highway applications. The most commonly used architecture is the series hybrid which offers great flexibility for implementation of power management strategies. But the direct connection of the high pressure accumulator to the system often results in operation of the hydraulic units in high pressure and low displacement mode. However, in this operating mode the hydraulic units are highly inefficient. Also, the accumulator renders the system highly compliant and makes the response of the transmission sluggish.

Diesel engine cylinder deactivation (CDA) can be used to reduce petroleum consumption and greenhouse gas (GHG) emissions of the global freight transportation system. Heavy duty trucks require complex exhaust aftertreatment (A/T) in order to meet stringent emission regulations. Efficient reduction of engine-out emissions require a certain A/T system temperature range, which is achieved by thermal management via control of engine exhaust flow and temperature. Fuel efficient thermal management is a significant challenge, particularly during cold start, extended idle, urban driving, and vehicle operation in cold ambient conditions. CDA results in airflow reductions at low loads. Airflow reductions generally result in higher exhaust gas temperatures and lower exhaust flow rates, which are beneficial for maintaining already elevated component temperatures. Airflow reductions also reduce pumping work, which improves fuel efficiency.

The effect of fuel injection pressure on the brake specific fuel consumption (BSFC) and brake specific particulate matter (BSPM) emissions at NOx parity (constant NOx emissions level) was investigated under different conditions of engine speed and load using a 2.5L DDC/VM-Motori common-rail, turbocharged, direct injection (DI), light-duty diesel engine. NOx parity at varying conditions of speed, load, and fuel injection pressure was achieved by changing the injection strategy and timing. The results of these analyses confirmed the well-established trends that soot emissions reduce with an increase in rail pressure at the expense of increasing NOx emissions. With an increase in engine speed (at constant load and NOx parity), it was observed that BSFC, CO, CO₂, and hydrocarbon emissions decreased, while BSPM decreased initially and increased later on. Increasing the fuel injection pressure resulted in an increase in BSFC, CO, CO₂, and hydrocarbon emissions.

The Pennsylvania State University Advanced Vehicle Team (PSUAVT) is one of sixteen collegiate teams across North America participating in the EcoCAR 2: “Plugging In to the Future” competition. The PSUAVT designed and implemented a series plug-in hybrid electric vehicle (PHEV) for this competition. This architecture allows the vehicle to operate as a pure electric vehicle until the energy storage system (ESS) state of charge (SOC) is depleted. The auxiliary power unit (APU) then supplements the battery to extend range beyond that of a purely electric vehicle. To implement this design concept, the PSUAVT re-engineered a General Motors (GM) donated 2013 Chevrolet Malibu to house an electric traction motor, high capacity lithium-ion battery pack, and APU consisting of a low-displacement engine fueled by 85% ethanol/15% gasoline (E85) mixture and an electric generator.

Bioregenerative systems for removal of gaseous contaminants are desired for long-term space missions to reduce the equivalent system mass of the air cleaning system. This paper describes an innovative design of a new biofiltration test lab for investigating the capability of biofiltration process for removal of ersatz multi-component gaseous streams representative of spacecraft contaminants released during long-term space travel. The lab setup allows a total of 24 bioreactors to receive identical inlet waste streams at stable contaminant concentrations via use of permeations ovens, needle valves, precision orifices, etc. A unique set of hardware including a Fourier Transform Infrared (FTIR) spectrometer, and a data acquisition and control system using LabVIEW™ software allows automatic, continuous, and real-time gas monitoring and data collection for the 24 bioreactors. This lab setup allows powerful factorial experimental design.

Data envelopment analysis (DEA) is used to examine the efficiency of 74 front wheel assist agricultural tractors from three U.S. manufacturers. The outputs of drawbar horsepower and power takeoff horsepower are modeled in a constant returns-to-scale framework using three productive performance inputs (fuel consumption, slip, and center of gravity), and one price input, namely, retail tractor price. The results suggest that by and large, John Deere tractors are more DEA efficient than their competitor's tractors. However, competitor's tractors that are DEA efficient are most often the top benchmarks for DEA inefficient tractors. These results suggest that while John Deere appears to produce many quality tractors, competitor's like CNH and AGCO produce a few tractors that may be of even higher quality.

Experiments were conducted with a commercially available six-cylinder, 4-valves per cylinder, turbocharged, direct injection (DI) diesel engine. The engine was operated with low sulfur diesel fuel, ultra low sulfur diesel fuel and two other blends, low sulfur diesel fuel with 20 wt.% biodiesel and ultra low sulfur diesel fuel with 20 wt.% biodiesel, to investigate the effect of the base fuels and their blends on combustion and emissions. Combustion analysis, particulate matter emissions and exhaust gas composition (CO, NOX and total hydrocarbons) were determined at eight steady-state operating conditions according to the AVL 8-Mode test protocol. Combustion analysis showed at high load conditions a retarded start of injection, an earlier start of combustion and a lower premixed burn peak with ultra low sulfur diesel fuel. Mode averaged NOX emissions decreased with ultra low sulfur diesel fuel and biodiesel blends compared to low sulfur diesel fuel.

Modern on-road vehicles have been making steady strides when it comes to employing technological advances featuring active safety systems. However, off-highway machines are lagging in this area and are in dire need for modernization. One chassis system that has been receiving much attention in the automotive field is the steering system, where several electric and electrohydraulic steering architectures have been implemented and steer-by-wire technologies are under current research and development activities. On the other hand, off-highway articulated steering vehicles have not adequately evolved to meet the needs of Original Equipment Manufacturers (OEM) as well as their end customers. Present-day hydrostatic steering systems are plagued with poor energy efficiency due to valve throttling losses and are considered passive systems relative to safety, adjustability, and comfort.

The effect of knock intensity on exhaust emissions was examined in a single cylinder spark ignition engine. The exhaust components surveyed were carbon monoxide, carbon dioxide, oxides of nitrogen (as NO), and total unburned hydrocarbons. Knock was induced solely by changing the spark timing. To describe knock intensity quantitatively, the magnitudes of the rate of pressure irregularities occurring during the combustion process were utilized. The use of the rate of pressure change to define a quantitative knock intensity scale is supported by an apparent generalization of the stoichiometric air-fuel ratio data. Graphs are presented that indicate the dependency of power output as well as exhaust emissions on knock intensity for various air-fuel ratios.

Raw oils generated by low-temperature coal pyrolysis were chemically characterized and subjected to tests in three diesel engines of different configuration. The coal liquids were tested as blends with conventional No. 2 diesel fuels, the coal liquids being 20-25% by volume. These tests were performed in support of a broader set of studies on the feasibility of using low-temperature pyrolysis to obtain liquid fuel materials from coal that do not require extensive, costly upgrading. Determination of physical and chemical properties of the pyrolysis liquids indicated a higher hydrogen/carbon ratio and lower aromaticity than typical SRC II and EDS middle distillates. Combustion tests were performed in both direct- and indirect-injection engines at three sites. The results were highly variable, the addition of the oil showing no effect on emissions and performance in some cases, reduced emissions on one engine, and increased emissions in other cases.

An experimental program was conducted to determine the effect of burning used lubricating oil mixed with fuel oil in a single cylinder Diesel engine. With increasing fuel costs, the prospect of using alternative fuels increases dramatically. Large quantities of used lubricating oil are currently available and could be used in fuel blends for Diesel engines. The used lubricating oil-fuel oil ratios used in this study were 2.5%, 5%, 10%, and 15% used lubricating oil by volume. The effect of burning these blends on unburned hydrocarbons, carbon monoxide and oxides of nitrogen is reported along with a comparison to baseline values for pure Diesel fuel. Tests were run at 1800, 2400 and 3000 rpm at 1/4, 1/2, 3/4 and full rack positions for each fuel blend. The general condition of wear in the engine along with deposit formation and analysis is reported. The effect of the used lubricating oil on thermal efficiency and BSFC is shown for the blends studied.