Search Results

Recent developments on highly downsized spark ignition engines have been focused on knocking behaviour improvement and the most advanced technologies combination can face up to 2.5 MPa IMEP while maintaining acceptable fuel consumption. Unfortunately, knocking is not the only limit that strongly downsized engines have to confront. The improvement of low-end torque is limited by another abnormal combustion which appears as a random pre-ignition. This violent phenomenon which emits a sharp metallic noise is unacceptable even on modern supercharged gasoline engines because of the great pressure rise that it causes in the cylinder (up to 20 MPa). The phases of this abnormal combustion have been analysed and a global mechanism has been identified consisting of a local ignition before the spark, followed by a propagating phase and ended by a massive auto-ignition. This last step finally causes a steep pressure rise and pressure oscillations.

In the context of CO₂ emission regulations and increase of energy prices, the downsizing of engine displacement is a widely discussed solution that allows a reduction of fuel consumption. However, high power density is required in order to maintain the power output and a good driveability. This study demonstrates the potential to strongly increase the specific power of High Speed Diesel Injection (HSDI) diesel engines. It includes the technological requirements to achieve high specific power and the optimal combination of engine settings to maximize specific power. The results are based on experimental work performed with a prototype single-cylinder engine (compression ratio of 14). Tests were conducted at full load, 4000 rpm. Part load requirements are also taken into account in the engine definition to be compatible with the targets of new emission standards.

Facing the CO2 emission reduction challenge, the combination of downsizing and turbocharging appears as one of the most promising solution for the development of high efficiency gasoline engines. In this context, as knock resistance is a major issue, limiting the performances of turbocharged downsized gasoline engines, fuel properties are more than ever key parameters to achieve high performances and low fuel consumption's levels. This paper presents a combustion study carried out into the GSM consortium of fuel quality effects on the performances of a downsized turbocharged Direct Injection SI engine. The formulation of two adapted fuel matrix has allowed to separate and evaluate the impacts of three major fuel properties: Research Octane Number (RON), Motor Octane Number (MON) and Latent Heat of Vaporization (LHV). Engine tests were performed on a single cylinder engine at steady state operating condition.

The combination of air charging and downsizing is known to be an efficient solution to reduce CO2 emissions of modern gasoline engines. The decrease of the cubic capacity and the increase of the specific performance help to reduce the fuel consumption by limiting pumping and friction losses and even the losses of energy by heat transfer. Investigations have been conducted on a highly downsized SI engine to confirm if a strong decrease of the displacement (50 %) was still interesting regarding the fuel consumption reduction and if other ways were possible to improve further more its efficiency. The first aim of our work was to identify the optimal design (bore, stroke, displacement, …) that could maximize the consumption reduction potential at part load but also improve the engine's behaviour at very high load (up to 3.0 MPa IMEP from 1000 rpm). In order to do that, four engine configurations with different strokes and bores have been tested and compared.

Engine downsizing is one of the most promising engine solutions to improve efficiency, but requires higher specific performance because of a lower engine displacement. The study is based on experimental work performed with an IFP prototype single cylinder engine, representative of passenger car applications. This engine enables very high specific power, with a high level of thermal and mechanical constraints. Tests were carried out on both full load and part load operation with a prototype common rail equipment capable of very high fuel pressure (up to 250 MPa). Results show that increasing fuel flow rate using fuel injection pressure instead of increasing nozzle hole diameter is more advantageous at full load, mainly because a lower nozzle hole diameter improves air entrainment. Benefits observed with increased injection pressure are enhanced when associated with upgraded engine thermo-mechanical limits, and advanced turbo charging system.

Among the last years, environmental concerns have raised the interest for biofuels. Ethanol, blended with gasoline seems particularly suited for the operation of internal combustion engines, and has been in use for severals years in some countries. However, it has a strong impact on engine performance, which is emphasized on recent engine architectures, with downsizing through turbocharging and variable valve actuation. Taking all the benefits of ethanol-blended fuel thus requires an adaptation of the engine management system. This paper intends to assess the effect of gasoline-ethanol blending from this point of view, then to describe a mean-value model of a fuel-flexible turbocharged PFI-SI engine, which will serve as a basis for the development of control algorithms. The focus will be in this paper on ethanol content estimation in the blend, supported by both simulation and experimental results.

In the whole engine development process, 0D/1D simulation has become a powerful tool, from conception to final calibration. Within the context of control strategy design, a turbocharged spark ignition (SI) engine with variable camshaft timing has been modelled on the AMESim platform. This paper presents the different models and the methodology used to design, calibrate and validate the simulator. The validated engine model is then used for engine control purposes related to downsizing concept. Indeed, the presented control strategy acts on the in-cylinder trapped mass, the in-cylinder burnt gas fraction and the air scavenging from the intake to the exhaust. Consequently, it permits to reduce not only the fuel consumption and pollutant emissions but also to improve the transient response of the turbocharger

Direct-injection represents a consolidated technology to increase performance and efficiency in spark-ignition engines. It reduces the knock tendency and makes engine downsizing possible through the use of turbocharging. Better control of CO and HC emissions at cold-start is also ensured since there is no wall-impingement in the intake port. However, to take advantages of all the theoretical benefits derived from GDI technology, detailed investigations of both fuel-air mixing and combustion processes are necessary to extend the stratified charge operations in the engine map and to reduce soot emissions, that are now severely regulated by emission standards. In this work, the authors developed a CFD methodology to investigate and optimize the fuel-air mixing process in direct-injection, spark-ignition engines. The Eulerian-Lagrangian approach is used to model the evolution of the fuel spray emerging from a multi-hole injector.

A robust optimization approach has been applied to the design of a piezoelectric brake. The force generated by the piezoelectric actuator is transmitted to the pad shoe through a lever. The optimal design of the lever is crucial for obtaining the desired performance of the brake. Increasing the stiffness and reducing the mass of the lever is the key problem for such kind of mechatronic brake. A trade off between mass and stiffness of the lever must be obtained. Multi-objective programming (MOP) has been applied in order to achieve the best compromise. In addition to MOP, the optimal robust design method has been applied to perform the optimal design not only by considering the performance of the system (the stiffness and mass of the lever) but also by taking into account the robustness (the sensitivity to the uncertain system parameters).