Search Results

For diesel engine, lower compression ratio has been demanded to improve fuel consumption, exhaust emission and maximum power recently. However, low compression ratio engine might have combustion instability issues under cold temperature condition, especially just after engine started. As a first step of this study, cold temperature combustion was investigated by in-cylinder pressure analysis and it found out that higher heat release around top dead center, which was mainly contributed by pilot injection, was the key factor to improve engine speed fluctuation. For further understanding of combustion in cold condition, particularly mixture formation near a glow plug, 3D CFD simulation was applied. Specifically for this purpose, TI (Time-scale Interaction) combustion model has been developed for simulating combustion phenomena. This model was based on a reasonable combustion mode, taking into account the characteristic time scale of chemical reactions and turbulence eddy break-up.

Traction control systems (TCSs) serve to control brake pressure and engine torque, thereby reducing driving wheel spin for improved stability and handling. Systems are divided into two basic types by the brake control configuration. One type is a one-channel left-right common control system and the other is a two-channel individual control system. This paper presents an analysis of these two types of TCS configurations in terms of handling, acceleration, stability, yaw convergence and other performance parameters. The systems are compared with and without a limited-slip differential (LSD) under various road conditions, based on experimental data and computer simulations. As a result of this work, certain Nissan models are now equipped with a new Nissan Traction Control System with a rear viscous LSD (Nissan V-TCS), which provides both the advantages of a rear viscous LSD in a small slip region and a two-channel TCS in a large slip region.

This paper describes the method used to design the basic control algorithm of a lane-keeping support system that is intended to assist the driver's steering action. Lane-keeping control has been designed with steering torque as the control input without providing a minor loop for the steering angle. This approach was taken in order to achieve an optimum balance of lane-keeping control, ease of steering intervention by the driver and robustness. The servo control system was designed on the basis of H2 control theory. Robustness against disturbances, vehicle nonlinearity and parameter variation was confirmed by μ - analysis. The results of computer simulations and driving tests have confirmed that the control system designed with this method provides the intended performance.

The influence on vehicle dynamics of braking force distribution to four wheels has been analyzed by computer simulation and experimentation. The analytical results indicate that a suitable braking force distribution control method can improve handling and stability during braking. A new braking force distribution cintrol strategy,using a steering wheel angle feedforward function and a yaw velocity feedback function,is shown to improve vehicle dynamic behavior.

Eliminating squeal noise generated during braking is an important task for the improvement of vehicle passengers' comfort. Considerable amount of research and development works have been done on the problem to date. In this study, we focused on the analyses of friction self-excited vibration and brake part resonance during high frequency brake squeal. Friction self-excited vibration is caused by the dry friction between pads and rotor, and occurs as a function of their relative sliding velocities. Its vibration frequency can be calculated in relation to the mass and stiffness of the pad sliding surface. Frequency responses of the brake assembly were measured and the vibration modes of the pad, disc and caliper during squeal were identified through modal analysis. Further study led to the development of a computer simulation method for analyzing the vibration modes of brake parts. Analytical results obtained using the method agreed well with the corresponding experimental data.

Electronic control of automatic transmission systems have become indispensable in order to satisfy driver expectations of comfort and vehicle response. The increasing complexity of such systems has resulted in a huge increase of control data volumes handled by electronic transmission control units (ETCUs). This paper describes the development, operation and evaluation by JATCO Corporation and Nissan Motor Co., Ltd of a Read Only Memory (ROM) management system for use with ETCUs. The system makes extensive use of computer aided design(CAD) techniques to create ROM data from standard format drawings, and vice-versa. The paper also presents the evaluation system developed for ETCU use. Making use of computer simulated testing, this increases the reliability of units and reduces testing time.

An automatic matching method for engine control parameters is described which can aid efficient development of new engine control systems. In a spark-ignition engine, fuel is fed to a cylinder in proportion to the air mass induced in the cylinder. Air flow meter characteristics and fuel injector characteristics govern fuel control. The control parameters in the electronic controller should be tuned to the physical characteristics of the air flow meter and the fuel injectors during driving. Conventional development of the engine control system requires a lot of experiments for control parameter matching. The new matching method utilizes the deviation of feedback coefficients for stoichiometric combustion. The feedback coefficient reflects errors in control parameters of the air flow meter and fuel injectors. The relationship between the feedback coefficients and control parameters has been derived to provide a way to tune control parameters to their physical characteristics.

In open-grille vehicle aerodynamics simulation using computational fluid dynamics, in addition to basic flow characteristics, such as turbulent flow with a Reynolds number of several million on the bluff body, it is important to accurately estimate the cooling air flow introduced from the front opening. It is therefore necessary to reproduce the detailed geometry of the entire vehicle including the engine bay as precisely as possible. However, there is a problem of generating a good-quality calculation grid with a small workload. It usually takes several days to a week for the pretreatment process to make the geometry data ‘clean’ or ‘watertight’. The authors proposed a computational method for complex geometries with a hierarchical Cartesian grid and a topology-independent immersed boundary method with dummy cells that discretize the geometry on a cell-by-cell basis and can set an imaginary point arbitrarily.

The engine cooling system is required to provide much higher performance today owing to the improved power output of engines and the trend toward a more compact engine compartment. For front engine/rear drive vehicles equipped with a fluid coupling drive fan, one of the main problems that must be dealt with is the rise in coolant temperature during idling. This paper presents a new method to simulate the engine coolant temperature under idling condition, and an improved engine cooling system that features a totally redesigned fan blade for maximum efficiency. This new system, consisting of a high performance cooling fan shroud and coupling, achieves a substantial noise reduction and contributes to fuel economy and power output improvements.

A human body model has been developed for conducting personal computer simulations to evaluate physical work loads, especially muscle loads, associated with the driving position and arm and leg motions. The validity of the model was confirmed by comparing estimated work loads with electromyographic measurements. Correlation analyses were conducted to examine the relationship between the estimated loads and subjective evaluations. The results indicated the regions of the body where loads had the largest impact on the perceived sensation of physical effort and were used to derive an index for evaluating the overall work load of the entire body. The simulation method was used to evaluate control switch positions, driving position and vehicle entry/exit motions.

An analysis was made of vibration phenomena in the steering system of a vehicle, when the front wheels have some amount of unbalance. The program included vehicle running tests and bench tests to ascertain some of the factors influencing vibration behavior. A mathematical model of the vibration system was simulated on a digital computer in as much detail as possible. The resultant understanding of the dynamics of the system as a whole led to an extensive theoretical analysis of selected key parameters.

Nissan’s new 2.8 liter in-line 6-cylinder turbocharged engine was developed for Che Datsun 280ZX in order to achieve higher performance and improved fuel economy. The Electronic Concentrated Engine Control System (ECCS), controlled by microprocessor, is provided for this 2.8 liter turbocharged engine. ECCS controls fuel injection, ignition timing, EGR rate and idling speed. It solved the problems related to power and fuel economy by optimizing the control parameters. Further, this system contains a barometric pressure compensator and a detonation controller; thus, the performance of this engine is efficient over a wide range of circumstances and fuel octane ratings. During the development of the engine, computer simulation was employed to predict engine performance and select turbocharger size, valve timing and other important factors.

A simulation system has been developed for making comprehensive predictions and assessments of the various and interrelated indices of vehicle performance. This system draws upon a data base containing information on the characteristics of the different units making up a vehicle. The system includes fuel economy and emissions calculation programs incorporating a large number of evaluation items. It also features an acceleration calculation program by which the transient characteristics of a turbocharger can be studied and a vehicle exterior noise program that makes accurate predictions of the pass-by noise level during acceleration. Equipped with a large number of calculation functions the system is an effective tool for improving total vehicle performance.

It has been reported by several researchers that the L-jetronic fuel injection system offers better idle speed stability than the D-jetronic one in port fuel injection engines. However, the volume between the throttle valve and the intake valves in the L-jetronic system acts as a first order lag element in the system and causes air-fuel ratio fluctuation which, in turn, induces idle speed hunting under certain conditions. This study employs computer simulation to determine the influence of three parameters on idle speed stability: (1) flywheel inertia, (2) intake manifold volume, and (3) air-fuel ratio calibration. It also explores means of improving idle speed stability by controlling the air-fuel ratio and ignition timing. The use of actual engine torque data to estimate the generated torque from the amount of air and fuel in each combustion cycle was the unique feature of this study.