Search Results

A strategy to actualize the dual-mode (SI mode and HCCI mode) operation of gasoline engine was investigated. The 4VVAS (4 variable valve actuating system), capable of independently controlling the intake and exhaust valve lifts and timings, was incorporated into a specially designed cylinder head for a single cylinder research engine and a 4VVAS-HCCI gasoline engine test bench was established. The experimental research was carried out to study the dynamic control strategies for transitions between HCCI and SI modes on the HCCI operating boundaries. Results show that equipped with the 4VVAS cylinder head, the engine can be operated in HCCI or SI mode to meet the demands of different operating conditions. 4VVAS enables the rapid and effective control over the in-cylinder residual gas, and therefore dynamic transitions between HCCI and SI can be stably achieved. It is easier to achieve transition from HCCI to SI than reversely due to the influence of thermo-inertia.

In this paper, HCCI combustion characteristics of three typical high octane number fuels, gasoline, ethanol and methanol, are compared in a Ricardo single cylinder port injection engine with compression ratio of 10.5. In order to trap enough high temperature residual gas to heat intake mixture charge for stable HCCI combustion, camshafts of the experimental engine are replaced by a set of special camshafts with low valve lift and short cam duration. The three fuels are injected into the intake port respectively in different mixture volume percentages, which are E0 (100% gasoline), E50 (50% gasoline, 50% ethanol), E100 (100% ethanol), M50 (50% gasoline, 50% methanol) and M100 (100% methanol). This work concentrates on the combustion and emission characteristics and the available HCCI operation range of these fuels. What's more, the detailed comparison of in-cylinder temperature, ignition timing and other parameters has been carried out.

To achieve homogeneous charge compression ignition (HCCI) combustion in the range of low speeds and loads, special camshafts with low intake/exhaust cam lift and short intake/exhaust cam duration were designed. The camshafts were mounted in a Ricardo Hydra four-stroke single cylinder port fuel injection gasoline engine. HCCI combustion was achieved by controlling the amount of trapped residuals from previous cycle through negative valve overlap. The results show that indicated mean effective pressure (IMEP) depends on valve timings, engine speeds and lambda. Early exhaust valve closing (EVC) timings result in high residual fractions in the cylinder and low air mass sucked into the cylinder. As a result, combustion duration increases, IMEP and peak pressure decrease. However, pumping losses decrease. High engine speed has the similar effect on HCCI combustion characteristics as early EVC timings do. But inlet valve opening timings have slight effect on IMEP compared to EVC timings.

One-dimensional engine simulation programmes are often used in the engine design and optimization studies. One of the key requirements of such a simulation programme is its ability to predict the heat release process during combustion. Such simulation software has built in it the heat release models for spark ignited premixed flame and compression ignited diesel combustion. The recent emergence of Controlled Auto Ignition (CAI) combustion, also known as Homogeneous Charge Compression Ignition (HCCI), has generated the need for a third type of heat release models for this new combustion process. In this paper, a heat release correlation for CAI combustion has been derived from extensive in-cylinder pressure data obtained from a Ricardo E6 single cylinder research engine and a multi-cylinder Port Fuel Injection (PFI) gasoline engine running with CAI combustion. The experimental data covered a wide range of air/fuel ratios, speed and percentage of residual gas.

With the application of valve timing strategy to inlet and exhaust valves, Homogeneous Charge Compression Ignition (HCCI) combustion was achieved by varying the amount of trapped residuals through negative valve overlap on a Ricardo Hydra four-stroke port fuel injection engine fueled with ethanol. The effect of ethanol on HCCI combustion and emission characteristics at different air-fuel ratios, speeds and valve timings was investigated. The results indicate that HCCI ethanol combustion can be achieved through changing inlet and exhaust valve timings. HCCI ethanol combustion range can be expanded to high speeds and lean burn mixture. Meanwhile, the factors influencing ignition timing and combustion duration are valve timing, lambda and speeds. Moreover, NOx emissions are extremely low under HCCI combustion. The emissions-speed and emissions-lambda relationships are obtained and analyzed.