Search Results

The goal of reducing fuel consumption and CO2-Emission is leading to turbo-charged combustion engines that deliver high torque at low speeds (down speeding). To meet NVH requirements damper technologies such as DMF (Dual Mass Flywheel) are established, leading to reduced space for the clutch system. Specific measures need to be considered if switching over from SMF (Single Mass Flywheel) to DMF [8]. Doing so has an impact on thermal behavior of the clutch system, for example due to reduced and different distribution of thermal masses and heat transfer to the surroundings. Taking these trends into account, clutch systems within vehicle powertrains are facing challenges to meet requirements e.g. clutch life, cost targets and space limitation. The clutch development process must also ensure delivery of a clutch system that meets requirements taking boundary conditions such as load cycles and driver behavior into account.

Automotive exterior lighting systems has to meet several regulatory requirements & manufacture specific internal standards to achieve desired performance. These test specifications are usually generic in nature and formulated mainly to validate the standalone product under standard laboratory conditions. Most of the time these specifications are common for entire vehicle portfolio. The rationale of these standards is to define the basic illuminance in the safe braking distance. Thus, however, using the requirements in these standards to evaluate the performance of front lighting systems is only qualitative. Research on working out method for quantitative evaluation of front lighting system is necessary [1] In practice, however, the luminance levels at road surfaces are usually very dynamic; depend largely on the variations in vehicle parameters, ambient weather conditions, road surface uniformities and effects of light intensity & color contrasts on target visibility.

With India achieving the BSVI milestone, the diesel particulate filter (DPF) has become an imperative component of a modern diesel engine. A DPF system is a device designed to trap soot from exhaust gas of the diesel engine and demands periodic regeneration events to oxidize the accumulated soot particles. The regeneration event is triggered either based on the soot mass limit of the filter or the delta pressure across it. For a Heavy Duty Diesel Engine (HDDE), pressure difference across the DPF is not usually reliable as the size of the DPF is large enough compared to the DPF used ina passenger vehicle diesel engine. Also, the pressure difference across DPF is a function of exhaust mass flow and thus it makes it difficult to make an accurate call for active regeneration. This demands for a very accurate soot estimation model and it plays a vital role in a successful regeneration event.

Fuel cells plays significant role in the automotive sector to substitute the fossil fuels and complement to electric vehicles. In the fuel cell vehicles fuel cell stack is major component. It is important to have a robust fuel cell model that can simulate the behaviour of the fuel cell stack under various operating conditions in order to study the functioning of a fuel cell and optimize its operating parameters and achieve the best efficiency in operation. The operating voltage of the fuel cell at different current densities depends upon thermodynamic parameters like temperature and pressure of the reactants as well factors like the state of humidification of the electrolyte membrane. A 1D model is developed to capture the variation in voltage at different current densities due to internal losses and changes to operating conditions like temperature and pressure.

Nowadays automotive cabin comfort has become a necessity rather than an optional feature, with customers demanding more comfort features. Thermal comfort becomes an essential part of this expectation. Since steering wheel is the first surface that the driver will touch once he enters the vehicle, maintaining thermal comfort of steering wheel becomes important, especially in tropical countries like India where a car parked in hot weather can get significantly warm inside. In this work, two design concepts for automotive steering wheel thermal control based on thermoelectric effect are depicted along with a detailed mathematical model. Thermoelectric coolers were selected for this purpose as it is solid state, compact & scalable solution to achieve rapid cooling rates. This was the desired feature expected from an integration standpoint in automotive architecture.

The public transport in India is gradually shifting towards electric mobility. Long range in electric mobility can be served with High Voltage Battery (HVB), but HVB can sustain for its designed life if it’s maintained within a specific operating temperature range. Appropriate battery thermal management through Battery Cooling System (BCS) is critical for vehicle range and battery durability This work focus on two aspects, BCS sizing and its coolant flow optimization in Electric bus. BCS modelling was done in 1D CAE software. The objective is to develop a model of BCS in virtual environment to replicate the physical testing. Electric bus contain numerous battery packs and a complex piping in its cooling system. BCS sizing simulation was performed to keep the battery packs in operating temperature range.

Brake system design is intended to reduce vehicle speed in a very short time by ensuring vehicle safety. In the event of successive braking, brake system absorbs most of vehicle’s kinetic energy in the form of heat energy, at the same time it dissipates heat energy to the surrounding. During this short span of time, brake disc surface and rotor attains the highest temperatures which may cross their material allowable temperature limit or functional requirement. High temperatures on rotor disc affects durability & thermal reliability of the brake rotor. Excessive temperature on brake rotors can induce brake fade, disc coning which may result in reduced braking efficiency. To address the complex heat transfer and highly transient phenomenon during successive braking, numerical simulations can give more advantage than physical trials which helps to analyze complex 3D flow physics and heat dissipation from rotors in the vicinity of brake system.

In previous work, AC Compressor Cycling (ACC) was modeled by incorporating evaporator thermal inertia in Mobile Air Conditioning (MAC) performance simulation. Prediction accuracy of >95% in average cabin air temperature has been achieved at moderate ambient condition, however the number of ACC events in 1D CAE simulation were higher as compared to physical test [1]. This paper documents the systematic approach followed to address the challenges in simulation model in order to bridge the gap between physical and digital. In physical phenomenon, during cabin cooldown, after meeting the set/ target cooling of a cabin, the ACC takes place. During ACC, gradual heat transfer takes place between cold evaporator surface and air flowing over it because of evaporator thermal inertia.

State of Charge (SoC) estimation of battery plays a key role in strategizing the power distribution across the vehicle in Battery Management System. In this paper, a model for SoC estimation using Extended Kalman Filter (EKF) is developed in Simulink. This model uses a 2nd order Resistance-Capacitance (2RC) Equivalent Circuit Model (ECM) of Lithium Ferrous Phosphate (LFP) cell to simulate the cell behaviour. This cell model was developed using the Simscape library in Simulink. The parameter identification experiments were performed on a new and a used LFP cell respectively, to identify two sets of parameters of ECM. The cell model parameters were identified for the range of 0% to 100% SoC at a constant temperature and it was observed that they vary as a function of SoC. Hence, variable resistance and capacitance blocks are used in the cell model so that the cell parameters can vary as a function of SoC.

Thermal Management System (TMS) is equally or more important part of Battery Electric (BEV)/Hybrid Electric vehicle (HEV) than an internal combustion engine (ICE) vehicle. In an ICE vehicle, TMS ensures performance of power train/engine, after treatment/exhaust system and HVAC (Climate control) whereas it connected with safety and Range anxiety elimination additionally for the case of Electric Vehicle. Electric powertrain is not a new technology to the world but the technology is evolving in last few decades, to overcome the cost and make it commercially viable, charging infrastructural development and elimination of Range Anxiety. In last few years, Indian automotive industry has taken some major steps towards electrification journey for both passenger car and commercial vehicle. In BEVs, Battery Cooling or Battery thermal management System (BTMS or BCS) and Traction cooling system (TCS) are couple with nearly conventional HVAC circuit used in any ICE vehicle.

The micro hybrid system, also known as the engine stop start system, has recently gained prominence world over due to its considerable fuel saving potential and relatively low costs. In spite of being a relatively non-complex function, the stop start system works hand-in-hand with a wide range of vehicle systems and components, specially the starting system and the battery. Frequent idle stop periods during city driving conditions can result in excessive battery discharge and gradually lead to loss of engine restartability. Increased number of charging and discharging cycles tend to reduce the life of the battery significantly. Hence it is very essential that the micro hybrid vehicles have a system in place that monitors and maintains the battery status within its operating limits.

This paper is related to a vehicle with rear engine which is turbo charged and inter cooled. Due to packaging constraints the intercooler was placed in front of turbocharger and was exposed to hot air radiated out from the turbo charger. This was in turn reducing the efficiency of the intercooler. In such scenario, it is essential to shield the turbo charger from the intercooler for proper hot air management. Also rear engine vehicles don't have the benefit of ram air affect. This necessitates increasing the air entering in to the core of the intercooler. Both the above mentioned issues associated with such a vehicle was resolved by ensuring that the hot air from turbo-charge is guided away from the intercooler as well as the air flow to Intercooler is increased. Guiding or throwing out the hot air away from Intercooler was done by introducing a heat shield or a baffle between the two.

Current Air Conditioning (AC) system uses hydrofluorocarbons (HFC) as refrigerant to transfer heat from cabin and cool the passengers. However, most refrigerants used today have severe environmental effects due to high global warming potential leading to global warming effects. Montreal Protocol and Kigali amendment calls for all nations to reduce refrigerant usage and transport sector being one of the main consumer of refrigerant, regulations regarding refrigerant usage and emission are becoming more stringent day by day. In this paper, a novel air-cycle refrigeration system has been designed and also tested for passenger vehicle applications. Automobile industry in developed countries has pivoted to R1234yf refrigerant for the most part, and has also rolled out R744 refrigerant for mass production to limited extent, which are in much lower Global warming potential (GWP) range than R134a.

Unfavorable climates, fatigue, safety & deprived sleep of driver’s leads to use of AC system for their quick thermal comfort during night with engine ON. This scenario is very critical from a human’s safety & vehicle functionality point of view. This also consumes an additional 10-15% of fuel requirements in AC running conditions. So, to address the social problems of driver’s sleep and pollution-free environment by reducing the use of fossil fuels, there is a need for alternative techniques for air cooling which work during engine OFF condition. Various alternative options for air cooling have been reviewed. Accordingly, the packaging flexibility of phase change material (PCM) technology makes it easy to implement, yet effective usage of large quantity stored PCM, needs optimization. This paper proposes a design of a hybrid air conditioning system for sleeper commercial vehicles using a combined conventional compression and phase change material.

This paper explains about the design & development of IHX for HCVs segment and vehicle level validation to get the actual benefits with this technology. Moreover, the data observed during vehicle testing also indicates the improvement in AC System Performance. This experiment was done on HCV platform vehicle with multiple actual test conditions with two designs of IHX. Final result shows the optimized AC system design to achieve better efficiency.

This paper summarizes the approach towards the process of computational simulation of the intake system and its experimental investigation. It is an important aspect to improve breathing of the diesel engines for performance, torque smoothening and emissions. This can be achieved by optimizing intake system parameters such as plenum volume, diameters, length of ports & runners, etc., which directly correlates the volumetric efficiency, thereby the performance of the engine. Keeping the objective of improving volumetric efficiency to achieve low-end performance, the intake system design optimization has been done on a twin cylinder, four cycle, compression ignition, In-Direct Injection (IDI) engine. For the simpler intake system, the primary pipe length & diameter can be calculated by mathematical formula applying Helmholtz Resonator principle. But, for a complex intake system, simulation software is used here.

During initial vehicle development stages thermal robustness is of prime importance. Vehicles are required to be validated for different drive cycles based on users driving patterns and also geographical road load database. Numerical simulations play key role in identifying critical thermal issues for different systems well in advance before physical validation. Hot shut down is one such case where thermal soak phenomenon plays vital role from thermal robustness point of view and there is a need to address this phenomenon using Computational Fluid Dynamics (CFD), which in turn will reduce the development time / testing efforts considerably. This condition is of utmost importance especially when vehicle is moving at higher gradients (uphill sections). In these critical conditions, hot engine compartment starves for cooling airflow despite the fact that fan is operating at maximum speed. The sudden stoppage of vehicle after this high thermal load is known as hot shut down.

Lithium-Ion batteries are popular for use in Electric vehicle (EV) applications. To improve and understand the use of Lithium-Ion batteries (LIBs) in EV application, present study focused and utilized equivalent circuit models (ECMs). Model parameters are identified using pulse charge and discharge test carried on 20Ah Lithium Iron Phosphate cell. Curve-fitting technique is utilized and detailed procedure to extract model parameters is presented. Models are validated with experimental data of pulse discharge test. Accuracy obtained using 1-RC, 2-RC, 3-RC circuit models is verified and high accuracy of 3RC circuit model can make it act as a battery emulator. Extended Kalman Filter (EKF) is utilized for estimation of State of Charge (SOC) of Lithium Iron Phosphate cell. As per our observation, a good accuracy with low computational burden can be achieved with 1RC model parameters.

Reckoning today's environmental rules, legislative regulation and market requirements- the automotive industry of late has witnessed an increased vigor and enthusiasm by auto makers towards electrification of vehicles across all platforms in a bid to improve fuel economy and performance. Hybridization of a vehicle often involves the use of expensive high performance motors and large battery packs. However due to the challenges associated with the packaging of bulky battery and motor systems in existing drive train, mild hybrid systems have been preferred over strong or full hybrids especially in current production models as they don't entail any major change in architecture and the reduced battery size, both of which provide for easier packaging of components.

A lightweight multi-material combination of steel and aluminium alloy (Al) is becoming a novel approach towards environmentally sustainable transport systems. Studies show that 10% reduction of vehicle weight results into 3-7% reduction in specific fuel consumption in IC engines and a 13.7% improvement in electric range for electric vehicles. However, dissimilar welding of Al/steel is a key challenge because of incompatible thermo-physical properties (melting point, thermal conductivity, and coefficient of thermal expansion) and low miscibility between Al and steel. The formation of brittle and hard Al-steel intermetallic compound (IMC) at the joint interface is the major concern for dissimilar welding of Al/steel. In this work, efforts are made to check the feasibility of Ni interlayer to control IMC formation at the interface of Al/steel dissimilar welded joint. Resistance spot welding is used to join low carbon steel CR01 and Al AA6061-T6 with pure Ni interlayer.