Search Results

Accident statistics shows pedestrian accident fatalities as one of the important concerns globally. In view of this, new test protocols for pedestrian safety have been drafted in regulation as well as in consumer group. Also as per new ENCAP requirements, pedestrian safety assessment is used as one of the four assessment criteria's (Adult protection, child safety, pedestrian safety, safety assist) in deciding the overall vehicle safety. Hence today importance of pedestrian safety is perceived as never before in vehicle development program. Basically pedestrian safety evaluation involves subsystem level (head form, upper leg form and lower leg form) impact tests representing human body parts, at specific region on test vehicle with injury limits to decide the severity of impact. In general these injuries are governed by vehicle styling, vehicle stiffness, hard points clearances from vehicle exterior like bonnet, bumper etc.

During cabin warm-up, effective air distribution by vehicle climate control systems plays a vital role. For adequate visibility to the driver, major portion of the air is required to be delivered through the defrost center ducts to clear the windshield. HVAC unit deliver hot air with help of cabin heater and PTC heater. When hot air interacts with cold windshield it causes thermal losses, and windshield act as sink. This process may causes in delay of cabin warming during consecutive cabin warming process. Thus it becomes essential to predict the effect of different windscreen defrost characteristics. In this paper, sensitivity analysis is carried for different windscreen defrosts characteristics like ambient conditions, modes of operation; change in material properties along with occupant thermal comfort is predicted. An integrated 1D/3D CFD approach is proposed to evaluate these conditions.

Automotive window buffeting is a source of vehicle occupant’s discomfort and annoyance. Original equipment manufacturers (OEM) are using both experimental and numerical methods to address this issue. With major advances in computational power and numerical modelling, it is now possible to model complex aero acoustic problems using numerical tools like CFD. Although the direct turbulence model LES is preferred to simulate aero-acoustic problems, it is computationally expensive for many industrial applications. Hybrid turbulence models can be used to model aero acoustic problems for industrial applications. In this paper, the numerical modelling of side window buffeting in a generic passenger car is presented. The numerical modelling is performed with the hybrid turbulence model Scale Adaptive Simulation (SAS) using a commercial CFD code.

Structural optimization has evolved vastly based on the development of computational based analysis – CAE. Structural optimization is usually a linear static response optimization because nonlinear response structural optimization is very expensive to perform. But in the real world, most of the automobile load cases are non-linear in nature. Equivalent static load structural optimization is a structural optimization method where Equivalent Static Loads (ESLs) are utilized as external loads for linear static response optimization. ESL is defined as the static load that generates the similar displacement by an analysis which is not linear static. This paper explains the development of a weight optimized BIW structure from an already existing model satisfying the NVH and Crash requirements. Basic structural crash loads are converted into ESLs with appropriate constraints.

Integrating safety features may lead to changes in vehicle interior component designs. Considering this complexity, design guidelines have to take care of aspects which may help in package feasibility studies that consider systems performance requirements. Occupant restraints systems for protection in side crashes generally comprise of Side Airbag (SAB) and Curtain Airbag (IC). These components have to be integrated considering design and styling aspects of interior trims, seat contours and body structure for performance efficient package definition. In side crashes, occupant injury risk increases due to hard contact with intruding structure. This risk could be minimized by cushioning the occupant contact through provision of SAB and Inflatable IC. This paper explains the methodology for deciding the package definitions using Knowlwdge Based Engineering (KBE) tools.

New noise regulations, with reduced noise limits, have been proposed by UN-ECE. A new method which aims at representing urban driving of the vehicles more closely on roads is proposed and is considerably different from the existing one (IS 3028:1998). It is more complex; we also found that some of the low powered vehicles can not be tested as per this method. The paper proposes ways of improvement in the test method. The new noise reduction policy options will have a considerable impact on compliance of many categories of vehicles. Technological challenges, before the manufacturers, to meet all performance needs of the vehicle along with the cost of development will be critical to meet the new noise limits in the proposed time frame.

The performance of door assembly is very significant for the vehicle design and door sag/set is one of the important attribute for design of door assembly. This paper provides an overview of conventional approach for door sag/set study based on door-hinge-BIW assembly (system level approach) and its limitation over new approach based on subassembly (subsystem level approach). The door sag/set simulation at system level is the most common approach adopted across auto industry. This approach evaluates only structural adequacy of door assembly system for sag load. To find key contributor for door sagging is always been time consuming task with conventional approach thus there is a delay in providing design enablers to meet the design target. New approach of door sag/set at “subsystem level” evaluates the structural stiffness contribution of individual subsystem. It support for setting up the target at subsystem level, which integrate and regulate the system level performance.

Engine cooling systems for vehicles are used for cooling the engine fluids. The cooling system normally consists of following components: radiator, expansion tank, cooling fan, fan drive and shroud. The mounting structure for this system must be designed to withstand the loads that will be imposed by the vehicle operation which consists of stresses such as those caused by linear static and dynamic loading. Automotive industries perform various tests on vehicles in the end-user environment to reduce failures; these investigations are carried out on the design using finite element method (FEM). Finite element methods are being used routinely to analyze for structural behavior. Modeling is done with CATIA software, meshing is carried out with HYPERMESH software and solution is acquired using NASTRAN solver.

The purpose of Federal Motor Vehicle Safety Standard 216 is to reduce fatalities and serious injuries when vehicle roof crushes into occupant compartment during rollover crash. Upgraded roof crush resistance standard (571.216a Standard No. 216a) requires vehicle to achieve maximum applied force of 3.0 times unloaded vehicle weight (UVW) on both driver and passenger sides of the roof. (For vehicles with gross vehicle weight rating ≤ 6,000 lb.) This paper provides an overview of current approach for dual side roof strength Finite Element Analysis (FEA) and its limitations. It also proposes a new approach based on powerful features available in virtual tools. In the current approach, passenger side loading follows driver side loading and requires two separate analyses before arriving at final assessment. In the proposed approach only one analysis suffices as driver and passenger side loadings are combined in a single analysis.

Increasing demands on engine power to meet increased load carrying capacity and adherence to emission norms have necessitated the need to improve thermal management system of the vehicle. The efficiency of the vehicle cooling system strongly depends on the fan and fan-shroud design and, designing an optimum fan and fan-shroud has been a challenge for the designer. Computational Fluid Dynamics (CFD) techniques are being increasingly used to perform virtual tests to predict and optimize the performance of fan and fan-shroud assembly. However, these CFD based optimization are mostly based on a single performance parameter. In addition, the sequential choice of input parameters in such optimization exercise leads to a large number of CFD simulations that are required to optimize the performance over the complete range of design and operating envelope. As a result, the optimization is carried out over a limited range of design and operating envelope only.

Conventionally, the automotive outer panels, giving vehicle its shape, have been manufactured from steel sheets. The outer panels are subjected to loads due to wind loading, palm-prints, person leaning on the vehicle, cart hits, and hail stones for example. Consumer awareness about these two panel characteristics: Oilcanning and Dent resistance is increased, which has been observed in recent marketing studies. Apart from perceptive quality, another factor depending on the dent performance is insurance and respective cost implications. Dents can occur due to several reasons such as object hits, parking misjudgement, hail stones etc. Phenomenon can be divided into two types, static and dynamic denting. Static dent case covers scenario wherein interaction with outer panel is mostly quasi-static. Hail stones present dynamic case where object hits a panel with certain kinetic energy. Automotive companies usually perform static dent assessment to cover all the cases.