Search Results

Accident statistics shows pedestrian accident fatalities as one of the important concerns globally. In view of this, new test protocols for pedestrian safety have been drafted in regulation as well as in consumer group. Also as per new ENCAP requirements, pedestrian safety assessment is used as one of the four assessment criteria's (Adult protection, child safety, pedestrian safety, safety assist) in deciding the overall vehicle safety. Hence today importance of pedestrian safety is perceived as never before in vehicle development program. Basically pedestrian safety evaluation involves subsystem level (head form, upper leg form and lower leg form) impact tests representing human body parts, at specific region on test vehicle with injury limits to decide the severity of impact. In general these injuries are governed by vehicle styling, vehicle stiffness, hard points clearances from vehicle exterior like bonnet, bumper etc.

Vehicle incab booming perception, a low frequency response of the structure to the various excitations presents a challenging task for the NVH engineers. The excitation to the structure causing boom can either be power train induced, depending upon the number of cylinders or the road inputs, while transfer paths for the excitation is mainly through the power train mounts or the suspension attachments to the body. The body responds to those input excitations by virtue of the dynamic behavior mainly governed by its modal characteristics. This paper explains in detail an integrated approach, of both experimental and numerical techniques devised to investigate the mechanism for boom noise generation. It is therefore important, to understand the modal behavior of the structure. The modal characteristics from the structural modal test enable to locate the natural frequencies and mode shapes of the body, which are likely to get excited due to the operating excitations.

In this work, Calculations and design of connecting rod of IC engine is performed in innovative way. Calculation point of view, Con rod is the utmost critical component of IC Engine as it is the part which translates reciprocating forces into rotary forces and thus creates unbalance in engine. From the functionality point of view, connecting rod must have the higher inertia at the lowest weight. Different forces acting on con rod are: - Peak combustion pressure, inertia force of reciprocating masses, Weight of Reciprocating parts and frictional forces due to cylinder wall thrust. It experiences complex forces of compression and tensile in cyclic manner, which repeats after each 720 (in case of 4 stroke) or 360 (in case of 2 stroke) phase of degree. Hence, the design calculations are analyzed for the axial compressive as well as axial tensile loads considering the fatigue strength of con rod. This literature computes the required size and strength in the critical areas of failure.

Battery Thermal management is a major challenge for occupant safety in an electric vehicle. Predicting the battery electrical losses and thermal behaviour is another challenge for the battery management system. Different virtual models are developed for cell level and pack level thermal evaluation. All these models have a varying degree of accuracy and limitation. The latest developed model is more accurate and can predict the battery cell & pack level temperatures. The battery can be modeled in different ways, ECM (Electrochemical model), EIS (Electrochemical Impedance Spectroscopy) [1]. Newman model is a well-known electrochemical model. [2]. EIS uses a combination of DC and small AC signal [3,4]. ECM model also used for estimating SOC and in BMS [5]. The cell temperature in the battery pack not only depends upon the cell inside physics but also depends upon cell outside cooling physics. Cell outside physics is simulated by 3D CFD software during the design process [6].

During cabin warm-up, effective air distribution by vehicle climate control systems plays a vital role. For adequate visibility to the driver, major portion of the air is required to be delivered through the defrost center ducts to clear the windshield. HVAC unit deliver hot air with help of cabin heater and PTC heater. When hot air interacts with cold windshield it causes thermal losses, and windshield act as sink. This process may causes in delay of cabin warming during consecutive cabin warming process. Thus it becomes essential to predict the effect of different windscreen defrost characteristics. In this paper, sensitivity analysis is carried for different windscreen defrosts characteristics like ambient conditions, modes of operation; change in material properties along with occupant thermal comfort is predicted. An integrated 1D/3D CFD approach is proposed to evaluate these conditions.

The jet lubrication method is extensively used in the constant mesh high performance transmission system operating at range of speeds though it affects mechanical efficiency through spin power loss. The lubrication jet has a key role to maintain the meshing gears at non-fatal thermal equilibrium by effectively dissipating the heat generated to the surrounding. Heat transfer coefficient (HTC) is the indicator of the thermal behavior of the system, which provides great insight of efficient lubrication system that needs to be employed for prescribed type of transmission. In this study, a segment of the transmission unit which constitutes a gear pair is used for the simulation. Parametric study is carried out by considering the critical parameters affecting the thermal performance such as lubrication jet flow rate and rotational motions of the gears with speeds and temperatures.

The brake system is one of the most critical systems in the automotive vehicle. Its design is a challenging task since stringent performance and packaging requirements are to be fully met - optimizing the brake performance and weight of the brake system. The brake disc is an important component in the braking system which is expected to withstand and dissipate the heat generated during the braking event. Validation of brake disc design through CAE/FEA is presented in this paper. The procedure for prediction of thermal performance was developed in-house, tuned and verified by correlating with Test data available for existing-design and then applied to the new-design brake disc. The correlation achieved for the existing-design brake disc (both solid and ventilated), procedure for prediction of thermo-mechanical performance (heat transfer coefficient estimation, temperature distribution etc.) are also included.

Anthropomorphic Test Devices (ATD) are the backbone of any crash research lab, their performance during the crash tests being of paramount importance to assess the vehicle performance. The Hybrid III 50th percentile dummy (H350) is one of the most recognized and accepted ATD for research in this field. However several unusual results of the dummy injuries in a vehicle crash test indicate some discrepancies exists in the dummy design. This prompted researchers to investigate such things and this paper is based on a project conducted to study the chest deflection of the hybrid 350 dummy. The project deals with assessing the dummy's chest deflection response sensitivity to load location as well as ambient operating conditions. The scope involved testing of the dummy chest by loading it quasi-statically on a UTM as well as dynamically impacting it on the dummy calibration rig. The chest deflection or thorax displacement data and loading data was gathered and analyzed further.

The modern trend of engine downsizing for CO₂ reduction coupled with stringent emission norms compel the engine air inlet system to outperform the conventional designs. Modern turbo diesel engine air inlet system handles higher & higher air flow, boost pressure and temperature. Air inlet system ducting designs have become complex due to oil particles (received through PCV system), engine movement and isolation for NVH. Air inlet ducting failures; like oil mist leakage through joints and seepage through hose wall cause high engine oil consumption and most predominantly environment damage. Also to some extent boost leakage in certain operating conditions. These failures reduce the reliability and performance of engine in certain conditions. This paper discusses design and development of cost-effective non-permeable and leak-proof hose-piping system for turbocharged diesel engine where PCV system was connected to air inlet system.

Computer Aided Engineering (CAE) plays an important role in the product development. Now a days major decisions like concept selection and design sign off are taken based on CAE. All the Original Equipment Manufacturers (OEMs) are putting consistent efforts to improve accuracy of the CAE results. In recent years confidence on CAE prediction has been increased mainly because of good correlation of CAE predictions with the test results. Defining proper correlation criteria and using a systematic approach helps significantly in building the overall confidence level for predictions given by CAE simulations. Representation of manufacturing effects on material properties and material failure in the simulation is still a big challenge for achieving a good CAE correlation. This paper describes side impact test vs CAE correlation. The important parameters affecting the CAE correlation were discussed.

Pedestrian impact test procedures allow tolerances on test conditions of impact such as mass of the impactor, impactor position, impact speed etc. The variation in these parameters affects the injury measurements in a test. This paper focuses on sensitivity study of variations in these parameters, within specified tolerances, on head form impact and lower leg impact injury measurements. The aim of this sensitivity study is to find out the most influencing test parameter for the injuries. The exercise was carried out using Computer Aided Engineering (CAE) simulations.

Engine Stop/Start System (ESS) promises to reduce greenhouse emissions and improve fuel economy of vehicles. Previous work of the Authors was concentrated on bridging the gap of improvement in fuel economy promised by ESS under standard laboratory conditions and actual driving conditions. Findings from the practical studies lead to a conclusion that ESS is not so popular among the customers, due to the complexities of the system operation and poor integration of the system design with the driver behavior. In addition, due to various functional safety requirements, and traffic conditions, actual benefits of ESS are reduced. A modified control algorithm was proposed and proven for the local driving conditions in India. The ways in which a given driver behaves on the controls of the vehicles like Clutch and Brake Pedals, Gear Shift Lever were not uniform across the demography of study and varied significantly.

Engine cooling systems for vehicles are used for cooling the engine fluids. The cooling system normally consists of following components: radiator, expansion tank, cooling fan, fan drive and shroud. The mounting structure for this system must be designed to withstand the loads that will be imposed by the vehicle operation which consists of stresses such as those caused by linear static and dynamic loading. Automotive industries perform various tests on vehicles in the end-user environment to reduce failures; these investigations are carried out on the design using finite element method (FEM). Finite element methods are being used routinely to analyze for structural behavior. Modeling is done with CATIA software, meshing is carried out with HYPERMESH software and solution is acquired using NASTRAN solver.

Increasing demands on engine power to meet increased load carrying capacity and adherence to emission norms have necessitated the need to improve thermal management system of the vehicle. The efficiency of the vehicle cooling system strongly depends on the fan and fan-shroud design and, designing an optimum fan and fan-shroud has been a challenge for the designer. Computational Fluid Dynamics (CFD) techniques are being increasingly used to perform virtual tests to predict and optimize the performance of fan and fan-shroud assembly. However, these CFD based optimization are mostly based on a single performance parameter. In addition, the sequential choice of input parameters in such optimization exercise leads to a large number of CFD simulations that are required to optimize the performance over the complete range of design and operating envelope. As a result, the optimization is carried out over a limited range of design and operating envelope only.