Search Results

Passenger cars in the top segment have seen fast growth over the last few decades with an increasing focus on luxury, convenience, safety and the quality of driver experience. The headliner is a decorative and functional trim system covering the underside of the roof panel. It enhances the aesthetics and elegance of the car interiors. In premium vehicles, the headliner system has to suffice interior quietness and integrity apart from the performance and regulatory requirements. The Design Validation Plan requirements cover its contribution to the vehicle interior noise control, occupant safety, and perception of build quality. Contributions can be very significant and primarily be determined by design and material parameters. Also, headliner interactions with an adjacent body in white structure are crucial from performance point of view. Various foam options are available with different functions such as structural, acoustic, and energy-absorption.

Battery Thermal management is a major challenge for occupant safety in an electric vehicle. Predicting the battery electrical losses and thermal behaviour is another challenge for the battery management system. Different virtual models are developed for cell level and pack level thermal evaluation. All these models have a varying degree of accuracy and limitation. The latest developed model is more accurate and can predict the battery cell & pack level temperatures. The battery can be modeled in different ways, ECM (Electrochemical model), EIS (Electrochemical Impedance Spectroscopy) [1]. Newman model is a well-known electrochemical model. [2]. EIS uses a combination of DC and small AC signal [3,4]. ECM model also used for estimating SOC and in BMS [5]. The cell temperature in the battery pack not only depends upon the cell inside physics but also depends upon cell outside cooling physics. Cell outside physics is simulated by 3D CFD software during the design process [6].

During cabin warm-up, effective air distribution by vehicle climate control systems plays a vital role. For adequate visibility to the driver, major portion of the air is required to be delivered through the defrost center ducts to clear the windshield. HVAC unit deliver hot air with help of cabin heater and PTC heater. When hot air interacts with cold windshield it causes thermal losses, and windshield act as sink. This process may causes in delay of cabin warming during consecutive cabin warming process. Thus it becomes essential to predict the effect of different windscreen defrost characteristics. In this paper, sensitivity analysis is carried for different windscreen defrosts characteristics like ambient conditions, modes of operation; change in material properties along with occupant thermal comfort is predicted. An integrated 1D/3D CFD approach is proposed to evaluate these conditions.

The jet lubrication method is extensively used in the constant mesh high performance transmission system operating at range of speeds though it affects mechanical efficiency through spin power loss. The lubrication jet has a key role to maintain the meshing gears at non-fatal thermal equilibrium by effectively dissipating the heat generated to the surrounding. Heat transfer coefficient (HTC) is the indicator of the thermal behavior of the system, which provides great insight of efficient lubrication system that needs to be employed for prescribed type of transmission. In this study, a segment of the transmission unit which constitutes a gear pair is used for the simulation. Parametric study is carried out by considering the critical parameters affecting the thermal performance such as lubrication jet flow rate and rotational motions of the gears with speeds and temperatures.

The brake system is one of the most critical systems in the automotive vehicle. Its design is a challenging task since stringent performance and packaging requirements are to be fully met - optimizing the brake performance and weight of the brake system. The brake disc is an important component in the braking system which is expected to withstand and dissipate the heat generated during the braking event. Validation of brake disc design through CAE/FEA is presented in this paper. The procedure for prediction of thermal performance was developed in-house, tuned and verified by correlating with Test data available for existing-design and then applied to the new-design brake disc. The correlation achieved for the existing-design brake disc (both solid and ventilated), procedure for prediction of thermo-mechanical performance (heat transfer coefficient estimation, temperature distribution etc.) are also included.

Ashcan contributes to the aesthetics and elegance of the vehicle interiors. It is used to store the ash. Generally the ashcan is fitted on the console of the car. The operational requirement of ashcan is to open with minimum force but not at very low accelerations experienced during the vehicle bump event. Also closing force should be comparatively higher. The closing of the ashcan lid should ensure positive locking, which may be achieved by using cam and follower locking mechanism. The other requirement is that it should be structurally durable enough to sustain the repetitive loading during its operation. Ashcan may undergo severe abusive loading during its operation. To simulate these operations and understand the physics of the problem, a multi-step non-linear analysis involving a complex contact situation is carried out. The scope of this paper is to explain the procedure of calculating the force required for closing and opening of the ashcan lid.

Engine cooling systems for vehicles are used for cooling the engine fluids. The cooling system normally consists of following components: radiator, expansion tank, cooling fan, fan drive and shroud. The mounting structure for this system must be designed to withstand the loads that will be imposed by the vehicle operation which consists of stresses such as those caused by linear static and dynamic loading. Automotive industries perform various tests on vehicles in the end-user environment to reduce failures; these investigations are carried out on the design using finite element method (FEM). Finite element methods are being used routinely to analyze for structural behavior. Modeling is done with CATIA software, meshing is carried out with HYPERMESH software and solution is acquired using NASTRAN solver.

The purpose of Federal Motor Vehicle Safety Standard 216 is to reduce fatalities and serious injuries when vehicle roof crushes into occupant compartment during rollover crash. Upgraded roof crush resistance standard (571.216a Standard No. 216a) requires vehicle to achieve maximum applied force of 3.0 times unloaded vehicle weight (UVW) on both driver and passenger sides of the roof. (For vehicles with gross vehicle weight rating ≤ 6,000 lb.) This paper provides an overview of current approach for dual side roof strength Finite Element Analysis (FEA) and its limitations. It also proposes a new approach based on powerful features available in virtual tools. In the current approach, passenger side loading follows driver side loading and requires two separate analyses before arriving at final assessment. In the proposed approach only one analysis suffices as driver and passenger side loadings are combined in a single analysis.

Increasing demands on engine power to meet increased load carrying capacity and adherence to emission norms have necessitated the need to improve thermal management system of the vehicle. The efficiency of the vehicle cooling system strongly depends on the fan and fan-shroud design and, designing an optimum fan and fan-shroud has been a challenge for the designer. Computational Fluid Dynamics (CFD) techniques are being increasingly used to perform virtual tests to predict and optimize the performance of fan and fan-shroud assembly. However, these CFD based optimization are mostly based on a single performance parameter. In addition, the sequential choice of input parameters in such optimization exercise leads to a large number of CFD simulations that are required to optimize the performance over the complete range of design and operating envelope. As a result, the optimization is carried out over a limited range of design and operating envelope only.

Conventionally, the automotive outer panels, giving vehicle its shape, have been manufactured from steel sheets. The outer panels are subjected to loads due to wind loading, palm-prints, person leaning on the vehicle, cart hits, and hail stones for example. Consumer awareness about these two panel characteristics: Oilcanning and Dent resistance is increased, which has been observed in recent marketing studies. Apart from perceptive quality, another factor depending on the dent performance is insurance and respective cost implications. Dents can occur due to several reasons such as object hits, parking misjudgement, hail stones etc. Phenomenon can be divided into two types, static and dynamic denting. Static dent case covers scenario wherein interaction with outer panel is mostly quasi-static. Hail stones present dynamic case where object hits a panel with certain kinetic energy. Automotive companies usually perform static dent assessment to cover all the cases.

Underrun Protection devices (UPDs) are specially designed barriers fitted to the front, side, or rear of heavy trucks. In case of accidents, these devices prevent small vehicles such as bikes and passenger cars going underneath and thus minimizing the severity of such accident. Design and strength of UPD is such that it absorbs the impact energy and offers impact resistance to avoid the vehicle under run. Compliance to UPD safety regulations provides stringent requirements in terms of device design, dimensions, and its behavior under impact loading. Since accuracy of Computer Aided Engineering (CAE) predictions have improved, numerical tools like Finite element method (FEM) are extensively used for design, development, optimization, and performance verification with respect to target regulatory performance requirements. For improved accuracy of performance prediction through FEA, correct FE representation of sub-systems is very important.