Search Results

This paper describes the development and experimental validation of a Plug-in Hybrid Electric Vehicle (PHEV) dynamic simulator that enables development, testing, and calibration of a traction control strategy. EcoCAR 2 is a three-year competition between fifteen North American universities, sponsored by the Department of Energy and General Motors that challenges students to redesign a Chevrolet Malibu to have increased fuel economy and decreased emissions while maintaining safety, performance, and consumer acceptability. The dynamic model is developed specifically for the Ohio State University EcoCAR 2 Team vehicle with a series-parallel PHEV architecture. This architecture features, in the front of the vehicle, an ICE separated from an automated manual transmission with a clutch as well as an electric machine coupled via a belt directly to the input of the transmission. The rear powertrain features another electric machine coupled to a fixed ratio gearbox connected to the wheels.

Objectives. Examination of head injuries in the Pedestrian Crash Data Study (PCDS) indicates that many pedestrian head injuries are induced by a combination of head translation and rotation. The Simulated Injury Monitor (SIMon) is a computer algorithm that calculates both translational and rotational motion parameters relatable head injury. The objective of this study is to examine how effectively HIC and three SIMon correlates predict the presence of either their associated head injury or any serious head injury in pedestrian collisions. Methods. Ten reconstructions of actual pedestrian crashes documented by the PCDS were conducted using a combination of MADYMO simulations and experimental headform impacts. Linear accelerations of the head corresponding to a nine-accelerometer array were calculated within the MADYMO model's head simulation.

There have been a number of papers written about the dynamic effects of low speed front to rear impacts between motor vehicles during the last several years. This has been an important issue in the field of accident analysis and reconstruction because of the frequency with which the accidents occur and the costs of injuries allegedly associated with them. Several of these papers have discussed the importance of the coefficient of restitution in the accelerations and speed changes that the vehicles undergo in such impacts. These discussions often include data showing the measured restitution for impacts involving various bumper types and closing speeds. However, in most of these studies, the impacts are controlled so that direct bumper to bumper impacts occur. This paper will present the results of several rear impact tests with non-standard impact configurations.

The advent of the Hybrid III crash test dummy marked the beginning of biofidelic anthropomorphic test devices. During the development of its critical components, notably the head, neck, knee, and thorax, biomechanical cadaver test results were incorporated into the design. The result was a dummy that represented the 50th percentile male during idealized impacts. In order to achieve a more biofidelic response from the components, many exotic materials and unique designs were utilized. The thorax, for instance, incorporates a spring steel rib design laminated with a viscoelastic polymeric composite material to damp the response. This combination results in the proper hysteretic losses necessary to model the human thorax under impact loading conditions. The disadvantage of this design is that the damping material properties are highly sensitive to temperature. A variation of more than 5 degrees Fahrenheit dramatically affects the response of the thorax.

In many manual transmissions, conditions for the onset of vibro-impacts from an unloaded gear pair are more likely than from an engaged set. Although some of the general characteristics of neutral gear rattle are known, no specific analytical models are available in the literature that can explain interactions between unloaded and loaded gear pairs in the drive rattle mode. For the sake of illustration, a particular problem for a light duty truck is studied in this paper and dynamic interactions are investigated. Some experimental measurements are first presented to define the unloaded gear rattle problem. Linear and non-linear mathematical models of the driveline are developed to understand, quantify and control the rattle problem. Trends predicted by simulations are compared with those observed in experiments. The effects of various gear run-ups and vibratory drag torques are investigated.

Current emission control systems utilize a catalytic converter employing a three-way catalyst (TWC), composed of a mixture of noble metals to minimize the three main pollutant classes of NOx, CO, and HC. The TWC is most efficient when the air-to-fuel ratio (A/F) is at stoichiometry (i.e. A/F ≈ 14.7). The stoichiometric set-point region is maintained by the use of oxygen sensors composed of the solid-electrolyte yttria stabilized zirconia (YSZ) in an electronic feedback loop. As combustion gets leaner a different exhaust sensor can be utilized to give a measure of the level of pollutants. A NOx sensor is an alternative for an oxygen sensor that can be used for feedback control of engine combustion or exhaust NOx traps. A solid electrolyte disk composed of YSZ having two Pt electrodes with one being covered by a microporous zeolite material was tested as a sensor for combustion produced gases such as NO and NO2 in the presence of O2.

This study involves two areas of research. The first is the finalization of the Pedestrian Crash Data Study (PCDS) in order to provide detailed information regarding the vehicle/pedestrian accident environment and how it has changed from the interim PCDS information. The pedestrian kinematics, injury contact sources, and injuries were analyzed relative to vehicle geometry. The second area presented is full-scale attempts at reconstruction of two selected PCDS cases using the Polar II pedestrian dummy to determine if the pre-crash motion of the pedestrian and vehicle could somehow be linked to the injuries and vehicle damage documented in the case.

Predominant failure modes in the forming of sheet metal parts are wrinkling and tearing. Wrinkling may occur at the flange as well as in other areas of the drawn part and is generated by excessive compressive stresses that cause the sheet to buckle locally. Fracture occurs in a drawn material which is under excessive tensile stresses. For a given part and blank geometries, the major factors affecting the occurrence of defects in sheet metal parts are the blank holder force (BHF) and the blank holder pressure (BHP). These variables can be controlled to delay or completely eliminate wrinkling and fracture. Modern mechanical presses are equipped with hydraulic cushions and various advanced multi-point pressure control systems. Thus, the BHP can be adjusted over the periphery of the blank holder as a function of location and time (or press stroke).

Plane strain bending (e.g. bending about a straight line) is a major sheet forming operation and it is practiced as brake bending (air bending, U-die, V-die and wiping-die bending). Precise prediction of springback is the key to the design of the bending dies and to the control of the process and press brake to obtain close tolerances in bent parts. In this paper, reliable mathematical models for press brake bending are presented. These models can predict springback, bendability, strain and stress distributions, and the maximum loads on the punch and die. The elasto-plastic bending model incorporates the true (nonlinear) strain distribution across the sheet thickness, Swift's strain hardening law, Hill's 1979 nonquadratic yield criterion for normal anisotropic materials, and plane strain deformation mode.

A newly developed process allows the near-net shape fabrication of alumina/aluminum composite bodies via the immersion of a sacrificial oxide preform into a molten aluminum alloy bath. The resulting composite possesses an attractive range of properties for application in several automotive components. These properties include: high strength and stiffness, appreciable thermal and electrical conductivity, high strength at elevated temperatures, coefficient of thermal expansion of 10 X 10-6 C-1 and relative ease of machinability. Low cost fabrication renders this material/process ideal for components such as brake rotors and calipers, cylinder bore liners, piston components.

Postcrash fires are a frequent cause of death in otherwise survivable automobile and aircraft accidents. The idea of the ICED (Internal Circuit Emergency Disconnect) battery [1] is to eliminate electrically ignited postcrash fires by means of an inertial interrupt device that will disconnect the active circuit at the battery if an accident should happen. The design of the prototypes that were tested and the analysis of the disengagement performance will be discussed. A ballistic pendulum impact test rig was designed and used to test the prototypes. The test results and analytical values were shown to be satisfactorily close to each other.

A new technique for measuring the friction coefficient between the punch and workpiece during sheet forming operations has been developed at the Ohio State University. Various materials, such as interstitial-free (IF) steel, high strength (HS) steel, an aluminum alloy (2008T4) and 70/30 brass, were tested under dry and oil lubrication conditions at different punch rates and process conditions. The results show that punch friction depends on the angle of wrap, which varies with punch stroke, and on the strain rate, which depends on punch velocity. The O.S.U. Friction Test is described and typical results are presented which verify the usefulness of the new procedure.

Heat exchanger design correlations are usually obtained from experiments performed on prototype heat exchangers. The data consist of total or overall thermal resistances which are usually separated into individual thermal resistances by appropriate manipulation. This paper presents an experimental investigation of the factors that affect the accuracy of the individual thermal resistances obtained from overall heat exchanger measurements. All experiments were performed such that one thermal resistance was varied while the other thermal resistances were kept nearly constant. The analysis that followed consisted of determining both the fixed and variable thermal resistances, together with their uncertainties.

A distributed parameter mathematical model of a complete power steering hydraulic transmission circuit has been developed and implemented on a personal computer to analyze the effect of tuning cables on the attenuation of pressure waves generated by the pump. Tuning cables, flexible tubes positioned coaxially inside a length of hose placed at a convenient location in the circuit, reduce fluidborne noise primarily by destructive interference and viscous damping. The model uses a transfer matrix approach that includes two-dimensional viscous flow and three-dimensional fluid-structure interaction. It can be used for sizing and positioning tuning cable devices in power steering as well as other hydraulic systems prior to verification testing of the circuit.

The process of producing co-continuous ceramic composite material has been investigated in order to provide a greater understanding of the formation mechanism and hence evaluate the viability of commercial applications for these exciting new materials. The ease of manufacture for components combined with the low production cost hold great promise for the production of brake rotors, brake calipers, piston crowns, cylinder liners, gears and turbine compressors. Practical issues such as bonding to this material, together with the machinability have been addressed, our findings are presented in this paper.

Ensuring the reliable operation of the emissions control system is a critical factor in complying with increasingly stringent exhaust emissions standards. In spite of significant advances, the performance of available diagnostic and test equipment is still amenable to further improvement, especially as it pertains to the diagnosis of incipient and intermittent faults. This paper presents experimental results pertaining to the diagnosis of complete, partial and intermittent faults in various components of the engine emissions control system. The instrumentation used in the study permitted simultaneous and essentially continuous analysis of the exhaust gases and of engine variables. Tests were conducted using a section of the EPA urban driving cycle (I/M 240), simulated by means of a throttle/dynamometer controller.

Shrink flanging is a major sheet forming operation to produce convex flanges in structural sheet metal components. Flanges are used for appearance, rigidity, hidden joints, and strengthening of the edge of sheet parts such as automobile front fender and complex panels formed by stretch/draw forming. Wrinkling around the flange edge is the major defect in shrink flanging operation. There has been a lack of reliable mathematical modeling to predict the strains and wrinkles in shrink flanging operations. A trial-and-error approach has been usually practiced in tooling and process designs. In this paper, a wrinkling criterion in shrink flange is proposed based on a simplification from a general criterion for a doubly curved anisotropic shell. The mathematical model for strain analysis in shrink flanging is established based on Wang and Wenner's strain model for stretch flange. Shrink flanging experiments were conducted to validate the theories.

In sheet metal forming, drawbeads are often used to control uneven material flow which may cause defects such as wrinkles, fractures, surface distortion and springback. Appropriate setting and adjusting the drawbead force is one of the most important parameters in sheet forming process control. However, drawbead design and drawbead force adjustment still rely on trial-and-error procedures. This paper summarizes the guidelines in drawbead design, evaluates a number of mathematical models in estimating drawbead forces, and investigates the effects of sheet thickness, material properties, drawbead geometry and penetration on the drawbead force.

Legislation pertaining to automobile emissions has caused an increased focus on the cold-start performance of internal combustion engines. Of particular concern is the period of time before all available sensors become active. Present engine control strategies must rely on methods other than feedback control while these sensors are not active. Without feedback control during this critical period, engine emissions performance is not optimized. These conditions cause difficulty in performing comprehensive cold-start experiments. For these reasons, we have developed several methods for feedback control during cold-start to aid in laboratory investigations of engine emissions phenomena.

We consider a vehicle-roadway system where the control of vehicle movement is based on the instrumentation located both in the vehicle and the roadway. In addition to the sensors which are used for obtaining the information on the vehicle, a radar based sensor system is used for providing information on the position of the car relative to a vehicle ahead, and with respect to a reflective strip placed on the road. The roadway traffic includes standard vehicles with no automatic control as well as the vehicles with automatic control units. Communication between the vehicles is not considered. For longitudinal control, we consider an Radar Based Cruise Control problem where the main goal is to maintain a desired speed set by the driver. At the same time, the controller will decelerate the vehicle if the distance and/or the relative speed between the controlled vehicle and the vehicles traveling in front are below certain limits.