Search Results

A 2 DOF nonlinear dynamic model of the automotive wiper system is established. Complex eigenvalues are calculated based on the complex modal theory, and the system stability as well as its dependence on wiping velocity is analyzed. Bifurcation characteristics of frictional self-excited vibration and stick-slip vibration relative to wiping velocity are studied through numerical analysis. Research of nonlinear vibration characteristics under various wiping velocities is conducted by means of phase trajectories, Poincaré map and frequency spectrum. The pervasive stick-slip vibration during wiping is confirmed, and its temporal and spatial distributions are analyzed by way of time history and contour map. Duty ratio of stick vibration and statistics of scraping residual are introduced as quantitative indexes for wiping effect evaluation. Results indicate that the negative slop of frictional-velocity characteristic is the root cause of system instability.

Startup from subzero temperature is one of the major challenges for polymer electrolyte membrane fuel cell (PEMFC) to realize commercialization. Below the freezing point (0°C), water will freeze easily, which blocks the reactant gases into the reaction sites, thus leading to the start failure and material degradation. Therefore, for PEMFC in vehicle application, finding suitable ways to reach successful startup from subfreezing environment is a prerequisite. As it’s difficult and complex for experimental studies to measure the internal quantities, mathematical models are the effective ways to study the detailed transport process and physical phenomenon, which make it possible to achieve detailed prediction of the inner life of the cell. However, review papers only on cold start numerical models are not available. In this study, an extensive review on cold start models is summarized featuring the states and phase changes of water, heat and mass transfer.

A new range-extension hybrid powertrain concept, namely the Tongji Extended-range Hybrid Technology (TJEHT) was developed and demonstrated in this study. This hybrid system is composed of a direct-injection gasoline engine, a traction motor, an Integrated Starter-Generator (ISG) motor, and a transmission. In addition, an electronically controlled clutch between the ISG motor and engine, and an electronically controlled synchronizer between the ISG motor and transmission are also employed in the transmission case. Hence, this system can provide six basic operating modes including the single-motor driving, dual-motor driving, serial driving, parallel driving, engine-only driving and regeneration mode depending on the engagement status of the clutch and synchronizer. Importantly, the unique dual-motor operation mode can improve vehicle acceleration performance and the overall operating efficiency.

Millions of configurations of power-split hybrid powertrain can be generated due to variation in number of planetary-gear sets (PG), difference in number, type and installation location of shift actuators (clutches or brakes), and difference in connection positions of power components. Considering the large number of configurations, complex structures and control modes, it is vital to construct an appropriate multi-index system evaluation method, which directly affects the requirement fulfillment, the time and cost of 2-PG system configuration design. Considering one-sidedness (dynamics and economic performance), simplicity (linear combination of indicators) and subjectivity (relying on expert experience) of previous system evaluation method of 2-PG system design, a more systematic evaluation method is proposed in this paper. The proposed evaluation system consists of five aspects, involving dynamic, economy, comfort, reliability and cost, and more than 20 indexes.

Engine start while driving is one of the most typical and frequent work conditions for hybrid vehicles. Engine start has very significant impact on the driving comfort. Engine start, especially a dynamical engine start, have high control requirements regarding control time, torque output and riding comfort. In some hybrid transmissions such as P2, engine is cranked and synchronized through wet clutch slipping. Because clutch pressure control has time-varying delay and estimation precision of engine torque by ECU (Engine Control Unit) is poor, conventional PID controller is unable to meet the high requirements of control quality. A new control algorithm is proposed in this paper to cope with all these challenges. The new control algorithm is based on LADRC (Linear Active Disturbance Rejection Controller) and is improved through combination with Smith predictor and Adaline network. LADRC is adopted to reduce negative effects of poor precision of engine torque.

With increasing pressure from environment problem for reduction in CO2 emissions and stricter fuel targets from road vehicles, new transmission technologies are gaining more attention in different main market. To get suitable road load data for transmission durability development is becoming increasingly important and can shorten the development time of new transmission. This paper presents the procedure and methods of road load data development for durability design of transmission product and optimization based on the real road data measurement, statistical characteristics evaluation and fatigue damage equivalency. Apply this road load data method procedure on 3 type of vehicle which represent conventional vehicle, BEV and HEV.

“Soichiro Honda Cup, Honda Econo-Power Competition”, is an annual international energy-saving competition which is hosted by Honda Motor Co., Ltd. Till now it has been held 27 sessions. The aims of the EP project are: promoting the development of environmental protection, making full use of limit earth resources, challenging the fuel consumption limitation of vehicle. Tongji University's students' team has participated in the competition for seven consecutive times. In order to minimize the fuel consumption of the EP energy-saving vehicle, this paper focuses on the technical methods of improving the fuel economy of the engine. Firstly, the optimization of the carburetor. Secondly, for the purpose of improving combustion efficiency, researches on dual spark plug and compression ratio are done.

The frame of a low-speed electric vehicle was treated as the research object in the paper. The fatigue load of the frame was analyzed with multi-body dynamics method and the fatigue life of frame was analyzed with the nominal stress method. Firstly, the multi-body dynamics model of the vehicle was established and the multi-body dynamics simulation was carried out to simulate the condition where the vehicle used to travel. The fatigue load history of the frame was obtained from the simulation. Secondly, the amplitude-frequency characteristic of the fatigue load was analyzed. The frequency of the fatigue load mainly focused on 0~20HZ from the analysis. Thirdly, the modal of frame was analyzed. As the frequency of the fatigue load was less than the natural frequency of the frame, the quasi-static method was selected to calculate the stress history of the frame. Next, the fatigue life of the frame was analyzed based on S-N curve.

Boosting and downsizing is the trend of future gasoline engine technology. For the turbocharged engines, the actuation of intake boosting pressure is very important to the performance output. In this paper, a GT-Power simulation model is built based on a 1.5 L turbocharged gasoline engine as the research object. The accuracy of model has been verified through the bench test data. Then it is conducted with numerical simulation to analyze the effect of wastegate diameter on the engine performance, including power output and fuel economy. Mainly the wastegate diameter is optimized under full engine operating conditions. Finally an optimal MAP of wastegate diameter is drawn out through interpolation method. By the transmission relationship between wastegate and actuator, a wastegate control MAP for electric actuated wastegate can be obtained.

X-in-the-loop (XiL) framework is a validation concept for vehicle product development, which integrates different virtual and physical components to improve the development efficiency. In order to develop and validate an extended validation method based on XiL, Tongji University in Shanghai, China and the Karlsruhe Institute of Technology (KIT) in Karlsruhe, Germany co- performed a feasibility study about an X-in-the-distance-loop demonstration platform. The X-in-the-distance-loop demonstration platform includes a MATLAB/Simulink software platform and geographically distributed equipment (driver simulator, driving electric motor and dynamometer test stand), which are used to conduct bidirectional experiments to test communication of powertrain data between China and Germany.

Jet-wake flow and secondary flows are undesirable in torque converters as they are responsible for flow losses and flow nonuniformity; that is, jet-wake flow and secondary flows negatively affect the torque converter performance. Therefore, it is very important to investigate and minimize the undesirable flows to decrease flow losses in torque converter. However, the existing studies are limited to employ geometry design parameter modifications rather than focusing on the actual causes and intrinsic physical mechanism that generate the flows to reduce the flow losses. In this paper, Calculation model of a torque converter is presented first and a three dimensional CFD code was used to simulate the internal flow field of a torque converter. The simulation results coincide with experimental measurements, which verifies the validity of the method. Based on flow field calculation results, the internal flow field of impeller, turbine and stator were analyzed, respectively.

Parallel-connected modules have been widely used in battery packs for electric vehicles nowadays. Unlike series-connected modules, the direct state inconsistency caused by parameter inconsistency in parallel modules is current and temperature non-uniformity, thus resulting in the inconsistency in the speed of aging among cells. Consequently, the evolution pattern of parameter inconsistency is different from that of series-connected modules. Since it’s practically impossible to monitor each cell’s current and temperature information in battery packs, considering cost and energy efficiency, it’s necessary to study how the parameter inconsistency evolves in parallel modules considering the initial parameter distribution, topology design and working condition. In this study, we assigned cells of 18650 format into several groups regarding the degree of capacity and resistance inconsistency. Then all groups are cycled under different environmental temperature and current profile.

Vehicle sideslip angle estimation is of great importance to the vehicle stability control as it could not be measured directly by ordinary vehicle-mounted sensors. As a result, researchers worldwide have carried out comprehensive research in estimating the vehicle sideslip angle. First, as the attitude would affect the acceleration information measured by the IMU directly, different kinds of vehicle attitude estimation methods with multi-sensor fusion are presented. Then, the estimation algorithms of the vehicle sideslip angle are classified into the following three aspects: kinematic model based method, dynamic model based method, and fusion method. The characteristics of different estimation algorithms are also discussed. Finally, the conclusion and development trend of the sideslip angle estimation are prospected.

For a practical pad design, a magnetic shielding layer is imperative which is made of ferrite, aluminum or some other metallic material. However, once the magnetic shielding layer is added, not only the mutual inductance but also the self-inductance of the coupling coils vary with the lateral misalignment which is inevitable for a human driver. The change of self-inductance will also result in the mistuning problem in the resonant circuit, which can significantly reduce the transmission efficiency of the whole wireless power transfer (WPT) system. This paper proposed a method of parameter identification of self-inductance based on the least square in order to solve the mistuning problem. In order to verify the proposed method, both the simulation model and the experiment set-up are built.

In order to research the vibration and noise reduction in pure electric vehicle power-train, a comprehensive work is to simulate the power-train incentive of a high-speed pure electric vehicle, and indicates significant impact of gear mesh system on the power-train NVH performance. Therefore, it is necessary to further study the impact of meshing gear system on electric vehicle power-train vibration and noise performance and seek reasonable methods to reduce the vibration and noise. In this paper, a typical pure electric vehicle's powertrain was used to conduct vibration and noise dynamic simulation. Firstly, the power train model was established considering the gear meshing stiffness, transmission errors, bearing factors and shell flexible, then the vibration and sound radiation dynamic response of power-train was simulated. Based on the accuracy of prediction model, a gear tooth modification was carried out for vibration and noise optimization.

Aerodynamic noise transmits through automotive window, causing great adverse influence on comfortability and noise-vibration-harshness (NVH) performance. However, the complicated external turbulent air flow, as well as the internal metal-rubber nonlinear sealing constraint, makes the mechanism of aerodynamic noise generation and transmission very difficult. Regarding the complex exterior aerodynamics-induced load and nonlinear metal-rubber interaction and constraint, an efficient two-step numerical prediction method is presented in order to study the mechanism of its generation and transmission. The first step uses the commercial ANSYS-Fluent computational fluid dynamics (CFD) analysis based on the shear stress transport (SST) - turbulence kinetic energy (k) - the rate of dissipation of turbulence kinetic energy ε (epsilon) model and Lighthill’s noise source theory.

Shift quality is an important indicator to measure the performance of dual-clutch transmissions (DCT). To obtain optimal driving comfort and reduce the vehicle jerk as much as possible, this paper proposes an integrated gearshift controller to control the engine and the on-coming clutch in inertia phase. First of all, a dynamic model of DCT during gearshift is established. Key factors determining shift quality are analyzed. In order to reduce the vehicle jerk, a reference trajectory of the engine speed and the derivative of the desired torque transferred by the on-coming clutch in inertia phase are programmed respectively. A back-stepping sliding mode controller (BPSMC) is designed to make the actual engine speed track the reference trajectory and an incremental proportional-integrative (PI) controller is designed to make the actual clutch torque to track the desired clutch torque.

Vehicle launch shudder is the terminology used in automotive industry to describe severe longitudinal oscillation during clutch engagement under start-up condition. This paper presents and implements detailed investigation for dry-clutch engagement and disengagement process, in order to deeply analyze vehicle launch shudder phenomenon which seriously deteriorates ride comfort. Firstly, diaphragm spring and cushion spring and link strip, which are three elastic components related to dry-clutch engagement and disengagement process in axial direction, are studied for their elastic properties, respectively, to obtain relationship between load and deflection. The elastic properties of these three elastic components are taken into considerations to establish nonlinear relationship between release bearing travel and clutch clamp force.

The rapid development of automotive technology has promoted the application of higher efficiency engines, while also putting higher requirements on the control of crankshaft torsional vibration. The traditional clutch driven disc torsional vibration damper can no longer meet the current new vibration and noise reduction requirements. Under these circumstances adopting dual mass flywheel (DMF) could be an efficient measure to reduce powertrain torsional fluctuations. For the sake of studying the torsional characteristics of DMF, a dual mass flywheel with circumstance arc spring (DMF-CS) is taken as the research subject. Firstly, According to lumped mass model, a multi-degree of freedom torsional vibration model of DMF-CS is established, which takes the mutual conversion of dry friction and viscous friction into consideration. Then, the overall and partial torsion characteristics of dual mass flywheel are obtained through numerical analysis.

The power-split transmission is considered as one of the major technologies for hybrid electric vehicles. It utilizes two electric motors/generators (MGs) and a power-split device (planetary gear sets) to make the speed of internal combustion engine (ICE) independent from the vehicle speed, and in that way enables the ICE to operate in a high-efficiency region under all driving cycles. In this study, a compound power-split hybrid system integrated with a two-planetary gear train is proposed. To suppress the vehicle jerk intensity and improve the driving comfort during the transition from EV (Electric Vehicle) mode to HEV (Hybrid Electric Vehicle) mode, a torque coordinated control strategy is derived. Based on the analysis of mode transition in different sections, mathematical models of each section are deduced, respectively. Then a model-based torque coordinated control method is used to solve out the target output torques of ICE, MGs and brakes in each mode transition phase.