Refine Your Search

Search Results

Viewing 1 to 9 of 9
Technical Paper

Material Compatibilities of Biodiesels with Elastomers, Metals and Plastics in a Diesel Engine

The effects of biodiesel on the swelling of the elastomers and plastics and the corrosion of metals are studied by the immersion tests. The results indicate that biodiesels make little corrosion effect on aluminum, steel and little swelling impact on plastics, but a significant corrosion may be taken place on cooper and brass for some sourced biodiesels. For nitrile-butadiene rubber, the variation of swelling properties in biodiesels is slightly higher than that in diesel. For the non-diesel-resistant elatomers, the variation of swelling properties is lower than those in diesel. The production process and biodiesel source have an influence on the result of elastomer swelling and corrosion. The relationship between the impact of biodiesel on materials and biodiesels properties are also discussed.
Technical Paper

An Experimental Study of the Yielding Locus of a TRIP780 Steel Sheet Using a Biaxial Tensile Test

The yield locus of a cold-rolled transformation-induced plasticity (TRIP780) steel sheet was investigated using a biaxial tensile test on a cruciform specimen. The effect of the key dimensions of the cruciform specimen on the calculation error and stress inhomogeneity was analyzed in detail using an orthogonal test combined with a finite element analysis. Scanning electron metallography (SEM) observations of the TRIP780 steel were performed. The yield curve of the TRIP780 steel was also calculated using the Von Mises, Hill '48, Hill '93, Barlat '89, Gotoh and Hosford yield criteria. The experimental results indicate that none of the selected yield criteria completely agree with the experimental curve. The Hill '48 and Hosford yield criteria have the largest error while the Hill '93 and Gotoh yield criteria have the smallest error.
Technical Paper

Energy Absorption Behavior and Application of Thin-walled Box Structure with Higher Strength in Ridgelines

To overcome some drawbacks of using AHSS (Advanced High Strength Steel) in vehicle weight reduction, like brittleness, spot weld HAZ (Heat Affected Zone) softening and high cost, a new ridgeline strengthening technology was introduced and applied to the thin-walled structure in this paper. The energy absorption mechanism of thin-walled box structure with selective strengthened ridgelines under axial compressing load was discussed in first section. After this, the formulas of mean crushing force and corresponding energy absorption for square tube were theoretically discussed. To demonstrate prediction capabilities of formulas, a set of FE simulations of square tubes were conducted. Simulation results show that energy absorption capacity of square tube under quasi-static axial crushing load is dramatically improved by selectively strengthening their ridgelines.
Technical Paper

Numerical Simulation of CFRP Thin-Walled Tubes Subjected to Quasi-Static Axial Crushing

Carbon Fiber Reinforced Plastic (CFRP) tube is an important material for the lightweight design of automotive structures. Simulation method of CFRP thin-walled tubes subjected to axial compression using MAT54 in LS-DYNA was investigated. Based on the two-layer shell model combined with MAT54, failure strategy and the parameters sensitivity of the model were discussed in detail. Then the simulation model was verified by using duplicate specimens comprised of carbon fiber/epoxy unidirectional prepreg tape. Furthermore, the modeling methods of crush trigger and different types of loading speed were analyzed. In addition, based on the method of equal energy absorption, energy absorption performance of thin-walled circular and square tubes made from four materials including mild steel, high strength steel, aluminum alloy and CFRP were also compared.
Technical Paper

Impact Mechanism of Multiple Major Welding Parameters on Mechanical Properties of Laser Brazing Lap Joint of Galvanized Steel for Vehicle

In order to research the effect of process parameters (laser power, welding speed, wire-feed speed, spot diameter) on mechanical properties of Zn-coated Steel Laser Brazing Lap Joint for vehicle, the influence of welding parameters on energy input of brazing seam cross section was theoretically analyzed, and then a great number of laser brazing experiments of 0.7mm galvanized steel was carried out. After that, the tensile strength and micro-hardness tests were also done for well-formed joints of galvanized steel formed in the laser brazing. The results show that joints with good mechanical properties and surface morphology can be formed when laser power is in the range of 2500-3200W and the other parameters keep in a specified range. Joint performance significantly reduces when the value of wire-feed speed exceeds 3.0m/min for that a wider brazing seam cross section can’t be formed.
Journal Article

Experimental Study of the Plasticity Responses of TRIP780 Steel Subjected to Strain-Path Changes

The work-hardening response of TRIP780 steel subjected to strain-path changes was investigated using two-stage tension experiments. Large specimens were prestrained and then sub-sized samples were subjected to tension along various directions. The influence of strain-path changes on flow stress and work hardening performance was discussed in detail. The specific plastic work was calculated to compare the kinematic hardening behaviour after strain-path changes. The results showed that transient hardening was observed for TRIP780 sheets subjected to orthogonal strain-path change. The strain-hardening exponent (n-value) was influenced by prestraining levels and the strain path. The n-value exhibited a greater decrease under an orthogonal strain-path change. Prestraining can delay the onset of high work hardenability of TRIP steels. It is meaningful for the safety design of vehicles.
Journal Article

Uncertainty Optimization of Thin-walled Beam Crashworthiness Based on Approximate Model with Step Encryption Technology

Crashworthiness is one of the most important performances of vehicles, and the front rails are the main crash energy absorption parts during the frontal crashing process. In this paper, the front rail was simplified to a thin-walled beam with a cross section of single-hat which was made of steel and aluminum. And the two boards of it were connected by riveting without rivets. In order to optimize its crashworthiness, the thickness (t), radius (R) and the rivet spacing (d) were selected as three design variables, and its specific energy absorption was the objective while the average impact force was the constraint. Considering the error of manufacturing and measurements, the parameters σs and Et of the steel were selected as the uncertainty variables to improve the design reliability. The algorithm IP-GA and the approximate model-RBF (Radial Basis Function) were applied in this nonlinear uncertainty optimization.
Journal Article

Investigation on Dynamic Recovery Behavior of Boron Steel 22MnB5 under Austenite State at Elevated Temperatures

Hot forming process of ultrahigh strength boron steel 22MnB5 is widely applied in vehicle industry. It is one of the most effective approaches for vehicle light weighting. Dynamic recovery is the major softening mechanism of the boron steel under austenite state at elevated temperatures. Deformation mechanism of the boron steel can be revealed by investigation on the behavior of dynamic recovery, which could also improve the accuracy of forming simulations for hot stamping. Uniaxial tensile experiments of the boron steel are carried out on the thermo-mechanical simulator Gleeble3800 at elevated temperatures. The true stress-strain curves and the relations between the work hardening rate and flow stress are obtained in different deformation conditions. The work hardening rate decreases linearly with increasing the flow stress.
Technical Paper

Lumped Parameter Transient Thermal Model of Motor Considering Temperature and Flow Rate of Cooling Water

The influence of heat flow and cooling water characteristics on motor temperature cannot be accurately reflected by the traditional motor temperature analysis method. In order to study the motor and its key components’ temperature characteristics under different temperatures and flow rates of cooling water, this paper establishes the lumped parameter transient thermal model which includes cooling water module, based on a 50kW permanent magnet synchronous motor. The transient and steady temperature is calculated through this model together with the motor loss calculation module in the electric drive system model. The influence of different temperature and flow rate of cooling water on motor and its key components’ temperature characteristics is compared. During the modeling process, the motor body is divided into 14 parts, based on the internal heat flow path of the motor. The thermal resistance of each key component and cooling water is calculated.