Search Results

A new experimental method, that enables to estimate the body and driveline sensitivity to unit transmitting error of a hypoid gear for automotive rear axle gear noise, has been developed. Measurements were made by exciting the tooth of the drive-pinion gear and that of the ring gear separately using the special devices designed with regard to simulation of acceleration and deceleration. The characteristic of this method is to estimate the forces at the contact point of the gears. Estimation of these forces is carried out under the condition that the higher stiffness is provided by the tooth of the drive-pinion gear and that of the ring gear, compared with the stiffness of the driveshafts and that of the propeller shaft etc., and relative angular displacement of the torsional vibration between the teeth of the drive-pinion gear and those of the ring gear is constant.

The synchronous belt employed in the valve train of automotive engines is operated under fluctuating load. Two types of the belt vibration are observed. One is the well-known lateral vibration. The other is the vibration in the belt running direction which may cause the resonant vibration of the camshaft rotation and may affect the belt life. The purpose of this paper is to describe an analysis of the latter vibration. This vibration was analyzed using the model composed of the inertia moment of the camshaft system and the nonlinear elasticity of the belt in the running direction. The predicted resonant frequency and amplitude were in good agreement with the measured ones. The influence of each factor of the model on the vibration was also investigated. The stiffness in the belt running direction that is determined by the tooth distortion When the belt engages with the pUlley should be increased to reduce the amplitudes of the resonant Vibration.

The finite element method (FEM) is effective for analyzing brake squeal phenomena. Although FEM analysis can be used to easily obtain squeal frequencies and complex vibration modes, it is difficult to identify how to modify brake structure design or contact conditions between components. Therefore, this study deals with a practical design method using sensitivity analysis to reduce brake squeal, which is capable of optimizing both the structure of components and contact conditions. A series of analysis processes that consist of modal reduction, complex eigenvalue analysis, sensitivity analysis and optimization analysis is shown and some application results are described using disk brake systems.

The design of the newly developed Toyota AZ series 4 cylinder engine has been optimized through both simulations and experiments to improve heat transfer, cooling water flow, vibration noise and other characteristics. The AZ engine was developed to achieve good power performance and significantly reduced vibration noise. The new engine meets the LEV regulations due to the improved combustion and optimized exhaust gas flow. A major reduction in friction has resulted in a significant improvement in fuel economy compared with conventional models. It also pioneered a newly developed resin gear drive balance shaft.

In the present social environment, automobile demands further reduction of fuel consumption and light weight. Now that the reduction of vehicle weight is being pursued, even a slight looseness in each element of an automobile may become a source of vibration and noise due to the lowered rigidity of such an automobile. The quietness of vehicles is urged, spline backlash in the spline mechanism exhibits a problem in some cases. A propeller shaft, a part of the automobile driving system, also has a sliding spline mechanism as shown in Fig. 1. Such a propeller shaft is required to have functions of transmitting high torque driving forces, and absorbing the variation of the vehicle driveline overall length at the same time. Vibration and noise are apt to occur if when torque is applied, there is a significant balance fluctuation or great sliding resistance due to spline backlash.

A description is made of new control methods to improve response of wheel slip regulation. These methods enabled a new Traction Control (TRC) system based on throttle control rather than brake pressure to be developed. Major points are as follows: (1) Use of fuel injection cut-off to minimize delay (2) Additional adaptive throttle control logic By these means, a response nearly equal to that with brake pressure control is achieved at lower cost and with a considerable weight saving. Furthermore, the system, by suppressing noise and vibration, enhances the driver's control ability.

The SEA model of wind noise requires the quantification of both the acoustic as well as the turbulent flow contributions to the exterior pressure. The acoustic pressure is difficult to measure because it is usually much lower in amplitude than the turbulent pressure. However, the coupling of the acoustic pressure to the surface vibration is usually much stronger than the turbulent pressure, especially in the acoustic coincidence frequency range. The coupling is determined by the spatial matching between the pressure and the vibration which can be described by the wavenumber spectra. This paper uses measured vibration modes of a vehicle window to determine the coupling to both acoustic and turbulent pressure fields and compares these to the results from an SEA model. The interior acoustic intensity radiating from the window during road tests is also used to validate the results.

Ongoing research on active stabilizers involves not only control of the roll angle of the vehicle based on steering input but also improving ride comfort by reducing roll vibration caused by the antiphase road surface input. In that context, roll skyhook control, which applies skyhook theory to provide feedback on the vehicle roll and drive the actuators, has already been presented. Although vibration in all frequency bands can be reduced if there is no control delay, time lags or phase delays in control elements such as the communication, computation, low-pass filter, or actuators can amplify vibration. Consequently, a sufficient effect of controlling cannot be obtained. This paper will address wheelbase filtering, which produces a frequency that minimizes roll oscillation, and is used to suppress the influence of the undesirable vibration.

The vehicle requires high brake performance and mass reduction of disc brake for vehicle fuel economy. Then disc brake will be designed by downsizing of disc and high friction coefficient pad materials. It is well known that disc brake squeal is frequently caused by high friction coefficient pad materials. Disc brake squeal is caused by dynamic unstable system under disturbance of friction force variation. Today, disc brake squeal comes to be simulated by FEA, but it is very difficult to put so many dynamic unstable solutions into stable solutions. Therefore it is very important to make it clear the influence of friction force variation. This paper describes the development of experimental set up for disc brake squeal basic research. First, the equation of motion in low-frequency disc brake squeal around 2 kHz is derived.

This paper investigates a new approach to the quantification technique for road induced vehicle interior noise and vibration within the frequency range up to 40 Hz. By employing the least squares method, both vertical and fore-aft load to each wheel were quantified using transfer function and actual vibration response of the vehicle driven on a road. The coupled structural-acoustic vehicle model using the finite element method, which is also detailed in this paper, is combined with the quantified input load to simulate road induced interior noise and vibration response. Experimental verification, which indicates reasonable accuracy of the simulation, and an application for the prototype development are also presented.

These days, a variety of navigation systems have been developed to provide the driver with necessary information such as vehicle location, direction and destination. An electronic compass is being widely used as a component for such navigation systems (1), (2) and (3). Compared with a conventional magnetic compass, an electronic compass has the following advantages: 1. High vibration durability and quick response. 2. Easy to calibrate and reliable. 3. Sensor and display units can be separated. The electronic compass, however, is accompanied by two serious subjects: the development of a sensitive geomagnetic sensor, and calibration of direction error due to an unexpectedly magnetized vehicle body. First, we developed a new geomagnetic sensor utilizing magnetoresistive elements (MRE) and magnetic lenses. Next, we clarified the magnetic disturbances and defined the mechanism of vehicle magnetization, thereby establishing a simple calibration technique for such magnetization.

Finite element aodels have been developed to analyze drive line and suspension vibration. For the analysis of booming noise, we have addressed the optimization of the differential gear carrier mounting system by using a virtual system and realization of it considering many constraints. To reduce the differential whine noise, a simulation method considering the transmitting error of the differential gear was applied. And we have approached for the subtle arrangements of many structural resonances with detail research of the drive line and suspension. For the reduction of road noise, we adopted the approach of shifting the node of the rear suspension member mode.

Engine running tests and excitation tests were performed to reveal the vibration behavior in a turbocharger-exhaust system related to the turbocharger's operating sound. The operating sound was caused by the resonant vibration excited by the unbalanced inertia force of the rotor. The turbocharger-exhaust system had six resonant frequencies in the operating speed range of the rotor. At resonant speeds, the whole turbocharger was translating or rotating due to bending and torsional deflection of the exhaust manifold. Based on the test results, the vibration behavior could be well simulated by a rigid body-spring model with six degree of freedom. Furthermore, the model was used to analyze the relation between the stiffness of the exhaust manifold and the vibration level. Increasing the stiffness of the exhaust manifold was effective in sufficiently reducing the vibration and sound.

This paper presents a new method of predicting judder occurrence. In this method, the friction characteristics of the clutch, that is, the relationship between the slip speed and the friction coefficient, and torsional vibration characteristics of the drive line are both considered. Judder occurrence is judged by calculating complex eigen values of a torsional vibration model of the drive line considering the clutch friction characteristics. This method is applied to judder phenomena of automatic transmissions. Comparisons between calculations and experiments are shown. Studies of the influence of viscous damping coefficients of drive line units are also described.

An active engine mount using a piezo actuator for a large vibrational amplitude is discussed. As a piezo actuator has a small displacement, the active mount requires a mechanism to increase the displacement of the piezo actuator to sufficiently counteract vibration. This paper describes in detail the construction of the prototype and the background theory from which the increase in displacement was achieved. Secondary, it describes a proving test performed on an experimental device that simulates the transfer of vibration from the engine to the chassis through the piezo active mounts. Finally it reports the decrease in floor vibration achieved when a piezo active mount was installed on an experimental vehicle.

In order to reduce the interior noise of a vehicle with a four-cylinder engine, investigations were made using finite element and vector methods, acoustic intensity testing and holography technique. The investigation resulted in inclination of the engine mounting, design changes to the front suspension member, a shock absorber engine mounting, structural modifications to reduce body panel vibration and a new engine mounting to insulate high frequency engine vibration.

An analysis system for vehicle noise and vibration has been developed. It consists of minicomputer based analog processing system connected with a large main-frame computer. This system features multi-modes for data analysis, fast data processing, data compatibility with conventional analog systems and feasibility. Fast data processing was achieved by newly developed FFT processor and minicomputer software. A new remote control box makes it simple to operate. Data processed by the minicomputer can be transferred to a large mainframe computer for further analysis.

On diesel vehicles, we frequently experience the phenomenon that low frequency fore and aft vibration of a vehicle, occurs at acceleration, does not decline in amplitude easily and rather increases finally. The phenomenon has recently attracted great concern in driveability problems on diesel vehicles. This phenomenon can not be explained well by the simple torsional vibration model of the powertrain with one node, which has been used so far successfully to analyze low frequency fore and aft vibration of a vehicle. So, we have assumed that the undamped vibration occurs through the interaction of the engine and the powertrain. Taking this interaction into consideration, we have constructed a simulation model, with which the undamped vibration can be simulated accurately. By this simulation model, we have estimated the order of magnitude of the effects of various design parameters affecting the undamped vibration.

Recently engine sound quality is becoming more noticeable as noise level in a vehicle passenger compartment has been decreasing. It is necessary to reduce such discomforting noise as rumbling noise in order to improve engine sound quality. This paper describes the experimental study to find out causes of rumbling noise in an engine structure and several investigations to reduce rumbling noise. Some new approaches have been introduced to evaluate the influence of an combustion impact, the movement of a crankshaft, timing of rumbling noise and so on. The result shows that the primary cause of rumbling noise is the movement of a crankshaft due to the impact of combustion and next is the vibration characteristics of the engine-transmission assembly (power plant). Finally superior engine sound quality is achieved by increasing counterweights and stiffness of a crankshaft and also by optimizing the spark advance and improving vibration characteristics of various engine parts.

Eliminating brake squeal generated during brake application is an important task for the improvement of comfort in the vehicle. There has been a lot of research made on the problem of brake squeal in the past. And most of the papers presented elaborate on low frequency brake squeal (2-3kHz). However, brake squeal has often the high-frequency vibration. For this reason, we have made research into the high-frequency brake squeal (5-10kHz). Double-Pulsed Laser Holography is a useful method for visualizing small vibration of brake components during brake squeal generation. The results obtained using Holographic Interferometry show the rotaing disc vibrates in the bending mode with diametral nodes. Consequently, we think that the modification of brake disc can eliminate brake squeal, which is caused by self-excited vibration. Then we have calculated natural frequency and its vibration mode of a circular-plate added mass.