Search Results

A kinematic analysis of the head-neck unit has been conducted in 37 simulated traffic accidents in order to investigate correlations between neck response and injuries. Belted fresh human cadavers in the age range 18 to 74 years have been used as front and rear-seat passengers. The analysed data included 23 frontal collisions, impact velocity 30 km/h, 50 km/h and 60 km/h, barrier impact and 14 90°-car to car lateral collisions with near-side passengers (6 cases) as well as far-side rear-seat passengers with an in-board upper anchoring point for the shoulder belt (8 cases). The head bending angle depended on the type of the collision. At the frontal collision, the mean head bending maxima amounted 79°, the evaluated mean angular velocity maxima and angular acceleration maxima corresponded to 41 rad/s and 2208 rad/s2, the mean maximum velocity in trajectory of the head was 10 m/s, the mean maximum acceleration along the path amounted 23 g.

The number of passenger cars equipped with side air bags is steadily increasing. With the aim of investigating the mechanical responses and the injuries of the arm under the influence of a side air bag, tests in probably higher injury risk configurations with dummies and cadavers were performed. The air bag was installed at the outer side of the seat back, with the subject seated in the driver or front passenger seat of a passenger car. During the inflation of the air bag, the left or right forearm of the subject was positioned on the arm rest while the upper arm made contact with the seat back edge. The volume of the thorax air bag was 15 litres and for the thorax-head air bag 28 litres. The dummy was instrumented at the thorax c.g. shoulder, elbow and wrist with triaxial accelerometers. In the cadaver, triaxial accelerations in three orthogonal directions were measured at the upper and the lower humerus, the upper radius and the lower radius and the first thoracic vertebrae.

The prevention of lower extremity injuries to front seat car occupants is a priority because of their potential to cause long-term impairment and disability. To determine the types and mechanisms of lower extremity injuries in frontal collisions, studies under controlled test conditions are needed. Sled tests using belt-restrained cadavers and dummies were conducted, in which footwell intrusion was simulated via a plane surface or simulated brake pedal. Human cadavers in the age range from 30 to 62 years and Hybrid III dummies were used. The footwell intrusion had both translational (135 mm) and rotational (30 degrees) components. Maximum footwell intrusion forces and accelerations were measured. The lower legs were instrumented with accelerometers and a ""six axis'' force-moment transducer was mounted in the mid shaft of the left tibia.

21 low velocity direct occipital and lateral head impacts were performed on 17 cadavers. Both damped and undamped impacts were performed at impact velocities of between 2.8 and 6.1 m/s. Head responses were measured using a 9-accelerometer array, and in 8 cases epidural pressure was measured at the contre-coup site. Base of skull and temporal fractures of AIS severity 3 or 4 were produced with undamped impacts at velocities greater than 4.0 m/s. Brain injuries were also observed; these were subdural and sub-arachnoid haematomas of AIS severity 3 or 4. Only minor cervical spine injuries were observed. Head responses were calculated from the 9-accelerometer array data. Linear centre of gravity head acceleration, HIC and angular accelerations are presented. Angular acceleration time-histories calculated with this method appear to be sensitive to local skull deformations and shock wave transmission.

The number of passenger vehicles with combined 3-point belt/driver air bag restraint systems is steadily increasing. To investigate the effectiveness of this restraint combination, 48 kph frontal collisions were performed with human cadavers. Each cadaver's thorax was instrumented with a 12-accelerometer array and two chest bands. The results show, that by using a combined standard 3-point belt (6% elongation)/driver air bag, the thoracic injury pattern remained located under the shoulder belt. The same observation was found when belts with 16% elongation were used in combination with the driver air bag. Chest contours derived from the chest bands showed high local compression and deformation of the chest along the shoulder belt path, and suggest the mechanism for the thoracic injuries.

A test series of 12 fresh cadavers and 5 Part 572 dummies is reported. The test configuration is frontal impact sled simulation at 30 mph and aims to simulate the restraint environment of a Volvo 240 car. The test occupants are restrained in a 3-point safety belt. The instrumentation of the surrogates involves mainly 12-accelerometers in chest, 9-accelerometers in head and 3-accelerometers in pelvis. Measured values are given and discussed together with the medical findings from the cadaver tests. The occurence of submarining with cadavers and dummies is reported. A comparison is also made with earlier work where both field accidents and sled simulatations of similar violence have been reported. It is concluded that there exist differences in kinematics between the dummy and the cadaver, although peak chest acceleration is similar in both conditions. The lap belt slides over the iliac crest more frequently in the cadaver tests than in the dummy tests.

The paper presents a report about car pedestrian impact simulations. The front of a production car, which was mounted on a platform moving on rails was used as impact vehicle. The test subjects were eleven unembalmed post mortem human subjects (PMHS) in the age range of 19 to 78 years, and the Hybrid II-P dummy. The test speeds ranged from 23 to 41 km/h. Accelerations of head, thorax and abdomen were measured on the test subject as well as at the inside of both the knee and the ankle of the impacted leg. High speed films were taken from the side view. In eight cases we noticed open tibia and fibula fractures of the impacted leg; usually associated with higher impact velocity or the age of the test subject; in one additional case a scapular fracture occurred at a collision velocity of 41 km/h. In 6 cases we observed vertebral column injuries of AIS 1, in two cases of AIS 2, and in one case of AIS 3. In no case did pelvic-, thoracic (skeletal) and skull fractures occur.

This paper documents seven car/car lateral collisions with belted farside rear seat occupants. The test subjects - cadavers and US SIDs - were restrained with a 3-point belt which had an inboard upper anchoring point for the shoulder belt. The collision velocity was 50 km/h. In the cadaver tests, the maximum resultant acceleration, an average of 18 G, was located at the clivus. In the US SID a maximum of 22 G occurred at the C.G. Average shoulder belt forces in the cadavers of 1,6 KN were measured compared to 2,5 KN in the US SID. Through an analysis of the high speed films, lateral head-neck bending angles of 40 to 65 degrees for the cadavers were investigated. The calculated angular velocities were between 13 and 38 rad/s and angular accelerations between 350 and 644 rad/s2. No head, thorax or pelvic injuries were observed. Belt-induced minor injuries at the skin on the neck, neck muscles and cervical spine were observed with a MAIS 1.

Six European laboratories have evaluated the biomechanical response of the new advanced frontal impact dummy THOR-alpha with respect to the European impact response requirements. The results indicated that for many of the body regions (e.g., shoulder, spine, thorax, femur/knee) the THOR-alpha response was close to the human response. In addition, the durability, repeatability and sensitivity for some dummy regions have been evaluated. Based on the tests performed, it was found that the THOR-alpha is not durable enough. The lack in robustness of the THOR-alpha caused a problem in completing the full test program and in evaluating the repeatability of the dummy. The results have demonstrated that the assessment of frontal impact protection can be greatly improved with a more advanced frontal impact dummy. Regarding biofidelity and injury assessment capabilities, the THOR-alpha is a good candidate however it needs to be brought up to standard in other areas.

The ultimate goal in the numerical simulation of automotive catalytic converters is the prediction of exhaust gas emissions as function of time for varying inlet conditions, i.e. the simulation of a driving cycle. Such a simulation must include the calculation of the transient three-dimensional temperature-field of the monolithic solid structure of the converter, which results from a complex interaction between a variety of physical and chemical processes such as the gaseous flow field through the monolith channels, the catalytic reactions, gaseous and solid heat transport, and heat transfer to the ambience. This paper will discuss the application of the newly developed CFD-code DETCHEMMONOLITH for the numerical simulation of the transient behavior of three-way catalytic converters that have a monolithic structure.