Refine Your Search

Search Results

Viewing 1 to 8 of 8
Technical Paper

Thermo-Mechanical Reliability of Nano-Silver Sintered Joints versus Lead-Free Solder Joints for Attaching Large-Area Silicon Devices

2010-11-02
2010-01-1728
Nano-silver sintered bonding was carried out at 275°C and under 3MPa pressures, and soldering in a vacuum reflowing oven to reduce voiding. Both joints are subject to large shear stresses due to the mismatch in coefficients of thermal expansion (CTE) between the chip and the substrate. In this study, residual stresses in the chip-on-substrate assemblies were determined by measuring the bending curvatures of the bonded structures. An in-house optical setup measured the bending curvatures using a thin-film stress measurement technique. From the measured bending curvatures and the mechanical properties of the constituent materials, residual stresses were calculated. The thermo-mechanical reliabilities of both joining techniques were tested by thermal cycling. The chip assemblies were cycled between -40°C and 125°C (100 minutes of cycle time, 10 minutes of dwell time) and the changes in their bending curvatures were measured.
Journal Article

Road Profile Estimation for Active Suspension Applications

2015-04-14
2015-01-0651
The road profile has been shown to have significant effects on various vehicle conditions including ride, handling, fatigue or even energy efficiency; as a result it has become a variable of interest in the design and control of numerous vehicle parts. In this study, an integrated state estimation algorithm is proposed that can provide continuous information on road elevation and profile variations, primarily to be used in active suspension controls. A novel tire instrumentation technology (smart tire) is adopted together with a sensor couple of wheel attached accelerometer and suspension deflection sensor as observer inputs. The algorithm utilizes an adaptive Kalman filter (AKF) structure that provides the sprung and unsprung mass displacements to a sliding-mode differentiator, which then yields to the estimation of road elevations and the corresponding road profile along with the quarter car states.
Technical Paper

Reliability Analysis of an Automotive Wheel Assembly

1993-03-01
930406
The incorporation of reliability theory into a fatigue analysis algorithm is studied. This probabilistic approach gives designers the ability to quantify “real world” variations existing in the material properties, geometry, and loading of engineering components. Such information would serve to enhance the speed and accuracy of current design techniques. An automobile wheel assembly is then introduced as an example of the applications of this durability/reliability design package.
Technical Paper

Probability-Based Methods for Fatigue Analysis

1992-02-01
920661
Modern fatigue analysis techniques, that can provide reliable estimates of the service performance of components and structures, are finding increasing use in vehicle development programs. A major objective of such efforts is the prediction of the field performance of a fleet of vehicles as influenced by the host of design, manufacturing, and performance variables. An approach to this complex problem, based on the incorporation of probability theory in established life prediction methods, is presented. In this way, quantitative estimates of the lifetime distribution of a population are obtained based on anticipated, or specified, variations in component geometry, material processing sequences, and service loading. The application of this approach is demonstrated through a case study of an automotive transmission component.
Technical Paper

Low Cycle Fatigue Properties of Al-Si Eutectic Alloys

1997-02-24
970704
The effect of Si-phase on the axial, low-cycle fatigue behavior of Al-Si eutectic alloys was investigated using test specimens prepared from alloys processed either by continuous casting or extrusion. Results indicate that, for continuous casting, all fatigue fractures resulted from shear-type crack initiation and propagation with an attendant shortening of fatigue life. For extruded material, fatigue cracks originated in the Si phase. In both instances, initiation and growth mechanisms were essentially identical to those observed in high-cycle fatigue. Cyclic properties obtained from phenomenological models are presented and discussed.
Technical Paper

Enhanced Low-Order Model with Radiation for Total Temperature Probe Analysis and Design

2017-09-19
2017-01-2047
Analysis and design of total temperature probes for accurate measurements in hot, high-speed flows remains a topic of great interest in aerospace propulsion and a number of other engineering areas. Despite an extensive prior literature on the subject, prediction of error sources from convection, conduction and radiation is still an area of great concern. For hot-flow conditions, the probe is normally mounted in a cooled support, leading to substantial axial conduction along the length of the probe. Also, radiation plays a very important role in most hot, high-speed conditions. One can apply detailed computational methods for simultaneous convection, conduction and radiation heat transfer, but such approaches are not suitable for rapid, routine analysis and design studies. So, there is still a place for low-order approximate methods, and that is the subject of this paper.
Technical Paper

Fuel Permeation Study on Various Seal Materials

2000-03-06
2000-01-1099
The advent of low emission regulations on fuel systems has made conventional sealing materials such as acry-lonitrile butadiene rubber (NBR) unfit for sealing most fuel systems. Therefore, it is imperative to look beyond conventional rubbers and towards more exotic materials to seal such applications. In this study, the permeation characteristics and the change in physical properties of several elastomeric materials (NBR, hydrogenated NBR (HNBR), and fluorocarbon elastomers (FKM)) as well as various poly(tetrafluoroethylene) (PTFE) composites were evaluated with four different fuel mixtures. The sealing materials were tested using vaporimeter cups. The results are discussed as a function of the materials' nature, composition, and filler content.
Technical Paper

Study on the Effects of Rubber Compounds on Tire Performance on Ice

2020-04-14
2020-01-1228
Mechanical and thermal properties of the rubber compounds of a tire play an important role in the overall performance of the tire when it is in contact with the terrain. Although there are many studies conducted on the properties of the rubber compounds of the tire to improve some of the tire characteristics such as the wear of the tread, there is a limited number of studies that focused on the performance of the tire when it is in contact with ice. This study is a part of a more comprehensive project looking into tire-ice performance and modeling. A significant part of this study is the experimental investigation of the effect of rubber compounds on tire performance in contact with ice. For this, four tires have been selected for testing. Three of them are completely identical in all tire parameters (such as tire dimensions), except for the rubber compounds. Several tests were conducted for the chosen tires in three modes: free rolling, braking, and traction.
X