Standard
TOLERANCES, METRIC Aluminum Alloy Drawn Tubing
1994-09-01
MAM2203B
Search Results
Standard
Spring 2022 Reaffirmation Ballot
2022-05-05
WIP
S2022DReaffirm
The documents listed in this ballot are being proposed for reaffirmation
Standard
Aluminum Alloy Bars, Rolled or Cold Finished 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T451) Solution Heat Treated and Stress Relieved by Stretching
2013-09-26
HISTORICAL
AMS4128D
This specification covers an aluminum alloy in the form of bars and rods 0.500 inch (12.50 mm) and over in nominal diameter or least difference between parallel sides.
Standard
Aluminum Alloy Bars, Rolled or Cold Finished 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T451) Solution Heat Treated and Stress Relieved by Stretching
2001-11-15
HISTORICAL
AMS4128C
This specification covers an aluminum alloy in the form of bars and rods 0.500 inch (12.50 mm) and over in nominal diameter or least difference between parallel sides.
Standard
ALUMINUM ALLOY BARS, ROLLED OR COLD FINISHED 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T451) Solution Heat Treated and Stress Relieved by Stretching
1995-05-01
HISTORICAL
AMS4128B
This specification covers an aluminum alloy in the form of bars and rods 0.500 in. (12.50 mm) and over in nominal diameter or least distance between parallel sides.
Standard
ALUMINUM ALLOY BARS, ROLLED, DRAWN, OR COLD FINISHED 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T451) Stress Relief Stretched
1979-01-01
HISTORICAL
AMS4128A
This specification covers an aluminum alloy in the form of bars and rods 0.500 in. (12.70 mm) and over in nominal diameter or least distance between parallel sides.
Standard
Aluminum Alloy Bars, Rolled or Cold Finished 1.0Mg - 0.60Si - 0.30Cu - 0.20Cr (6061-T451) Solution Heat Treated and Stress Relieved by Stretching
2021-06-28
CURRENT
AMS4128E
This specification covers an aluminum alloy in the form of bars and rods 0.500 inch (12.7 mm) to 8.000 inches (203.2 mm) in nominal diameter or least difference between parallel sides and up to 50 square inches (322.6 square centimeters) in cross-sectional area (see 8.7).
Standard
Aluminum Bronze Rods, Bars, and Forgings 90.5Cu - 7.5Al - 1.95: Stress Relieved
2011-11-03
HISTORICAL
AMS4631E
This specification covers one type of aluminum bronze in the form of rods, bars, forgings, and forging stock.
Standard
TOLERANCES Aluminum and Aluminum Alloy Bars, Rods and Shapes Extruded
1996-08-01
HISTORICAL
AMS2205
Standard
TOLERANCES Aluminum and Magnesium Alloy Extrusions
1965-02-15
HISTORICAL
AMS2205G
Standard
TOLERANCES Aluminum and Magnesium Alloy Extrusions
1964-01-31
HISTORICAL
AMS2205F
Standard
TOLERANCES Aluminum and Magnesium Alloy Extrusions
1966-03-15
HISTORICAL
AMS2205J
Standard
TOLERANCES Aluminum and Magnesium Alloy Extrusions
1965-09-01
HISTORICAL
AMS2205H
Standard
TOLERANCES Aluminum and Aluminum Alloy Extrusions and Magnesium Alloy Extrusions
1951-06-01
HISTORICAL
AMS2205B
Standard
TOLERANCES Aluminum and Magnesium Alloy Extrusions
1963-01-15
HISTORICAL
AMS2205E
Standard
TOLERANCES Aluminum and Magnesium Alloy Extrusions
1960-06-30
HISTORICAL
AMS2205D
Standard
TOLERANCES Aluminum Alloy and Magnesium Alloy Extrusions
1991-10-01
HISTORICAL
AMS2205M
This specification covers established manufacturing tolerances applicable to aluminum alloy and magnesium alloy extruded bar, rod, wire, shapes, and tubing ordered to inch/pound dimensions. Tolerances greater than standard may be necessary for some shapes; tolerances closer than standard may be possible for others. Tolerances shown herein, however, apply unless otherwise agreed upon by purchaser and vendor and apply to all tempers, unless otherwise noted. The term "excl" is used to apply only to the higher figure of the specified range. The general temper designations "-TX510" and "-TX511" are used for brevity and denote the full temper designations -T3510, -T4510, -T6510, -T8510, -T73510, -T76510, -T3511, -T4511, -T6511, -T8511, -T73511, and -T76511, the "X" representing one or more digits preceding the "510" or "511".
Standard
TOLERANCES Aluminum and Magnesium Alloy Extrusions
1967-11-01
HISTORICAL
AMS2205K
Standard
TOLERANCES Aluminum-Base and Magnesium-Base Alloy Extrusions
1973-05-15
HISTORICAL
AMS2205L
This specification covers established manufacturing tolerances applicable to aluminum-base and magnesium-base alloy extruded bar, rod, wire, shapes, and tubing. Tolerances greater than standard may be necessary for some shapes; tolerances closer than standard may be possible for others. Tolerances shown herein, however, apply unless otherwise agreed upon by purchaser and vendor and apply to all tempers, unless otherwise noted. The term "excl" is used to apply only to the higher figure of the specified range. The general temper designations "-TX510" and "-TX511" are used for brevity and denote the full temper designations -T3510, -T4510, -T6510, -T8510, -T73510, -T76510, -T3511, -T4511, -T6511, -T8511, -T73511, and -T76511, the "X" representing one or more digits preceding the "510" or "511".
Standard
ALUMINUM SHEET, LAMINATED Edge Bonded
1969-11-01
HISTORICAL
AMS4012B
