Search Results

Direct injection (DI) and jet ignition (JI), plus assisted turbocharging, have been demonstrated to deliver high efficiency, high power density positive ignition (PI) internal combustion engines (ICEs) with gasoline. Peak efficiency above 50% and power density of 340 kW/liter at the 15,000 rpm revolution limiter working overall λ=1.45 have been report-ed. Here we explore the further improvement in power density that may be obtained by replacing gasoline with ethanol or methanol, thanks to the higher octane number and the larger latent heat of vaporization, which translates in an increased resistance to knock, and permits to have larger compression ratios. Results of simulations are proposed for a numerical engine that uses rotary valves rather than poppet valves, while also using mechanical, rather than electric, assisted turbocharging. While with gasoline, the power density is 410-420 kW/liter, the use of oxygenates permits to achieve up to 475 kW/liter working with methanol.

Cold start driving cycles exhibit an increase in friction losses due to the low temperatures of metal and media compared to normal operating engine conditions. These friction losses are responsible for up to 10% penalty in fuel economy over the official drive cycles like the New European Drive Cycle (NEDC), where the temperature of the oil even at the end of the 1180 s of the drive cycle is below the fully warmed up values of between 100°C and 120°C. At engine oil temperatures below 100°C the water from the blowby condensates and dilutes the engine oil in the oil pan which negatively affects engine wear. Therefore engine oil temperatures above 100°C are desirable to minimize engine wear through blowby condensate. The paper presents a new technique to warm up the engine oil that significantly reduces the friction losses and therefore also reduces the fuel economy penalty during a 22°C cold start NEDC.

Improvements of vehicle fuel economy may be achieved by the introduction of advanced internal combustion engines (ICE) improving the fuel conversion efficiency of the engine and of advanced power trains (PWT) reducing the amount of fuel energy needed to power the vehicle. The paper presents a novel design of a variable compression ratio advanced spark ignition engine that also permits an expansion ratio that may differ from the compression ratio hence generating an Atkinson cycle effect. The stroke ratio and the ratio of maximum to minimum in-cylinder volumes may change with load and speed to provide the best fuel conversion efficiency. The variable ratio of maximum to minimum in-cylinder volumes also improves the full load torque output of the engine.

Recovery of kinetic energy during driving cycles is the most effective option to improve fuel economy and reduce green house gas (GHG) emissions. Flywheel kinetic energy recovery systems (KERS) may boost this efficiency up to values of about 70%. An engine and vehicle model is developed to simulate the fuel economy of a compact car equipped with a TDI diesel engine and a KERS. Introduction of KERS reduces the fuel used by the 1.6L TDI engine to 3.16 liters per 100 km, corresponding to 82.4 g of CO₂ per km. Downsizing the engine to 1.2 liters as permitted by the torque assistance by KERS, further reduces the fuel consumption to 3.04 liters per 100 km, corresponding to 79.2 g of CO₂ per km. These CO₂ values are 11% better than those of today's most fuel efficient hybrid electric vehicle.

Downsizing and Turbo Charging (TC) and Direct Injection (DI) may be combined with Variable Valve Actuation (VVA) to better deal with the challenges of fuel economy enhancement. VVA may control the load without throttle; control the valve directly and quickly; optimize combustion, produce large volumetric efficiency. Benefits lower fuel consumption, lower emissions and better performance and fun to drive. The paper presents an engine model of a 1.6 litre TDI VVA engine specifically designed to run pure ethanol, with computed engine maps for brake specific fuel consumption and efficiency. The paper also presents driving cycle results obtained with a vehicle model for a passenger car powered by this engine and a traditional naturally aspirated gasoline engine. Preliminary results of the VVA system coupled with downsizing, turbo charging and Direct Injection permits significant driving cycle fuel economies.

Recovery of braking energy during driving cycles is the most effective option to improve fuel economy and reduce green house gas (GHG) emissions. Hybrid electric vehicles suffer the disadvantages of the four efficiency-reducing transformations in each regenerative braking cycle. Flywheel kinetic energy recovery systems (KERS) may boost this efficiency up to almost double values of about 70% avoiding all four of the efficiency-reducing transformations from one form of energy to another and keeping the vehicle's energy in the same form as when the vehicle starts braking when the vehicle is back up to speed. With reference to the baseline configuration with a 1.6 liters engine and no recovery of kinetic energy, introduction of KERS reduces the fuel usage to 3.16 liters per 100 km, corresponding to 82.4 g of CO₂ per km. The 1.6 liters Turbo Direct Injection (TDI) diesel engine without KERS uses 1.37 MJ per km of fuel energy, reducing with KERS to 1.13 MJ per km.

Cylinder deactivation has been proposed so far for improved part load operation of large gasoline engines. In all this application, the cylinder deactivation has been achieved keeping the intake and exhaust valves closed for a particular cylinder, with pistons still following their strokes. The paper presents a new mechanism between the piston and the crankshaft to enable selective deactivation of pistons, therefore decoupling the motion of the piston from the rotation of the crankshaft. The reduced friction mean effective pressure of the new technology enables the use of piston deactivation in large engines not necessarily throttle controlled but also controlled by quantity of fuel injected. Results of performance simulations are proposed for a HSDI V8 engine, producing significant savings during light operation.

Prior papers have shown the potentials of gasoline-like internal combustion engines fitted with waste heat recovery systems (WHR) to deliver Diesel-like steady state fuel conversion efficiencies recovering the exhaust and the coolant waste heat with off-the-shelf components. In addition to the pros of the technology significantly increasing steady state efficiencies - up to 5 % in absolute values and much more in relative values - these papers also mentioned the cons of the technology, increased back pressures, increased weight, more complex packaging, more complex control, troublesome transient operation, and finally the cold start issues that prevent the uptake of the technology. This paper further explores the option to use Rankine cycle systems to improve the fuel economy of vehicles under normal driving conditions. A single Rankine cycle system is integrated here with the engine design.

The turbocharged direct injection stoichiometric spark ignition gasoline engine has less than Diesel full load brake engine thermal efficiencies and much larger than Diesel penalties in brake engine thermal efficiencies reducing the load by throttling. This engine has however a much better power density, and therefore may operate at much higher BMEP values over driving cycles reducing the fuel economy penalty of the vehicle. This engine also has the advantage of the very well developed three way catalytic converter after treatment to meet future emission regulations. In these engines the efficiency may be improved recovering the waste heat, but this recovery may have ultimately impacts on both the in cylinder fuel conversion efficiency and the efficiency of the after treatment.

Advanced Vehicle Technologies (AVT), a Ballarat Australia based company, has developed the World's first diesel to 100% LPG conversion for heavy haul trucks. There is no diesel required or utilized on the trucks. The engine is converted with minimal changes into a spark ignition engine with equivalent power and torque of the diesel. The patented technology is now deployed in 2 Mercedes Actros trucks. The power output in engine dynamometer testing exceeds that of the diesel (in excess of 370 kW power and 2700 Nm torque). In on-road application the power curve is matched to the diesel specifications to avoid potential downstream power-train stress. Testing at the Department of Transport Energy & Infrastructure, Regency Park, SA have shown the Euro 3 truck converted to LPG is between Euro 4 and Euro 5 NOx levels, CO2 levels 10% better than diesel on DT80 test and about even with diesel on CUEDC tests.

Real driving cycles are characterized by a sequence of accelerations, cruises, decelerations and engine idling. Recovering the braking energy is the most effective way to reduce the propulsive energy supply by the thermal engine. The fuel energy saving may be much larger than the propulsive energy saving because the ICE energy supply may be cut where the engine operates less efficiently and because the ICE can be made smaller. The present paper discusses the state of the art of hydro-pneumatic drivelines now becoming popular also for passenger cars and light duty vehicle applications permitting series and parallel hybrid operation. The papers presents the thermal engine operation when a passenger car fitted with the hydro-pneumatic hybrid driveline covers the hot new European driving cycle. From a reference fuel consumption of 4.71 liters/100 km with a traditional driveline, the fuel consumption reduces to 2.91 liters/100 km.

Direct injection and jet ignition is becoming popular in electrically assisted, turbocharged, F1 engines because of the pressure to reduce fuel consumption. Operation from homogeneous stoichiometric up to lean of stoichiometry stratified about λ = 1.5, occurs with fast combustion of reduced cyclic variability thanks to the enhanced ignition by multiple jets of hot, partially reacting products travelling through the combustion chamber. The fuel consumption has thus been drastically reduced in an engine that is, however, still mostly throttle controlled. The aim of the present paper is to show the advantages of direct injection and jet ignition based on model simulations of the operation of a high-performance throttle-controlled engine featuring rotary valves.

The World Championship Grand Prix (WCGP) is the premier championship event of motorcycle road racing. The WCGP was established in 1949 by the sport's governing body, the Fédération Internationale de Motocyclisme (FIM), and is the oldest world championship event in the motorsports arena. This book, developed especially for racing enthusiasts by motorsports engineering expert Dr. Alberto Boretti, provides a broad view of WCGP motorcycle racing and vehicles, but is primarily focused on the design of four-stroke engines for the MotoGP class. The book opens with general background on MotoGP governing bodies and a history of the event’s classes since the competition began in 1949. It then presents some of the key engines that have been developed and used for the competition through the years. Technologies that are used in today’s MotoGP engines are discussed.