Search Results

Better understanding of flow phenomena inside the combustion chamber of a diesel engine and accurate measurement of flow parameters is necessary for engine optimization i.e. enhancing power output, fuel economy improvement and emissions control. Airflow structures developed inside the engine combustion chamber significantly influence the air-fuel mixing. In this study, in-cylinder air flow characteristics of a motored, four-valve diesel engine were investigated using time-resolved high-speed Tomographic Particle Imaging Velocimetry (PIV). Single cylinder optical engine provides full optical access of combustion chamber through a transparent cylinder and flat transparent piston top. Experiments were performed in different vertical planes at different engine speeds during the intake and compression stroke under motoring condition. For visualization of air flow pattern, graphite particles were used for flow seeding.

Biodiesel is mono alkyl ester derived from vegetable oils through transesterification reaction and can be used as an alternative to mineral diesel. In the present research, methyl ester of rice-bran oil (ROME) is produced through transesterification of rice-bran oil using methanol in presence of sodium hydroxide (NaOH) catalyst. Various properties like viscosity, density, flash point, calorific value of the biodiesel thus prepared are characterized and found comparable to diesel. On the basis of previous research for performance, emission and combustion characteristics, a 20% blend of ROME (B20) was selected as optimum biodiesel blend for endurance test. Endurance test of 100 hours was conducted on a medium duty direct injection transportation diesel engine. Tests were conducted under predetermined loading cycles in two phases: engine operating on mineral diesel and engine fuelled with 20% biodiesel blend.

Homogeneous charge compression ignition (HCCI) engines are attracting attention as next-generation internal combustion engines mainly because of very low NOx and PM emission potential and excellent thermal efficiency. Particulate emissions from HCCI engines have been usually considered negligible however recent studies suggest that PM number emissions from HCCI engines cannot be neglected. This study is therefore conducted on a modified four cylinder diesel engine to investigate this aspect of HCCI technology. One cylinder of the engine is modified to operate in HCCI mode for the experiments and port fuel injection technique is used for preparing homogenous charge in this cylinder. Experiments are conducted at 1200 and 2400 rpm engine speeds using gasoline, ethanol, methanol and butanol fuels. A partial flow dilution tunnel was employed to measure the mass of the particulates emitted on a pre-conditioned filter paper.

The development of more efficient and powerful internal combustion engines requires the use of new and advanced engine technologies. These advanced engine technologies and emission requirements for meeting stringent global emission norms have increased the power densities of engine leading to downsizing. In all these engines, cylinder head and liner are normally cooled but the piston is not cooled, making it susceptible to disintegration/ thermal damage. Material constraints restrict the increase in thermal loading of piston. High piston temperature rise may lead to engine seizure because of piston warping. So pistons are additionally cooled by oil jet impingement from the underside of the piston in heavy duty diesel engines. However, if the temperature at the underside of the piston, where the oil jet strikes the piston, is above the boiling point of the oil, it may contribute to the mist generation.

Vegetable oils are produced from numerous oil seed crops. While all vegetable oils have high energy content, most require some processing to assure safe use in internal combustion engines. Some of these oils already have been evaluated as substitutes for diesel fuels. However, several operational and durability problems of using straight vegetable oils in diesel engines are reported in the literature, caused by of their higher viscosity and low volatility compared to mineral diesel. In the present research, experiments were designed to study the effect of reducing Jatropha oil's viscosity by blending it with mineral diesel and thereby eliminating the effect of high viscosity and poor volatility on combustion characteristics of the engine. Experimental investigations have been carried out to examine the combustion characteristics of an indirect injection transportation diesel engine running with diesel, and jatropha oil blends with diesel.

The interface between the piston rings and cylinder liner play an important role in total frictional losses and mechanical wear of internal combustion engine and is increasingly coming under scrutiny as legislated particulate emission standards are getting more and more stringent. The capacitance method is used for measurement of minimum oil film thickness between piston ring and liner interface. Measurement of capacitance formed between the piston ring and a probe mounted flush in the liner provides an accurate means of determining the oil film thickness provided that the region between the probe and liner is flooded with oil and dielectric constant of the oil is known. This paper presents detailed design and measurement of lubricating oil film thickness using capacitive micro sensor in a non-firing engine simulator. Lubricating oil film thickness was found to vary between 0.2μm to 8μm in the non firing engine simulator.

Biodiesel is being explored as a sustainable renewable fuel for vehicles in India due to mounting foreign exchange expenditure to import crude petroleum. Significant amount of research and development work is being undertaken in India to investigate various aspects of biodiesel utilisation in different types of engines. This study is an effort to jointly investigate the use of biodiesel (B100) in an unmodified BS-III compliant sports utility vehicle (SUV) by a consortium of academia (IIT Kanpur) and Industry (M&M) to realistically assess whether biodiesel is compatible with modern engine technology vehicles. Two identical vehicles were operated in tandem using biodiesel (B100) and mineral diesel (B00) respectively for 30,000 kilometers in field conditions. The lubricating oil samples were collected and detailed analysis for assessing the comparative effect of new fuel (B100) vis-à-vis mineral diesel was carried out.

Increased environmental awareness and depletion of resources are driving industry to develop alternative fuels that are environmentally more acceptable. Fatty acids esters (biodiesel) are known to be good alternative fuels. Due to economic reasons, the use of cheap raw materials for biodiesel production is preferred. In this case, ricebran oil, non-edible grade is used. Base catalyzed transesterification of ricebran oil is investigated and process parameters for ricebran biodiesel production are optimized. Various properties like viscosity, density, flash point, calorific value of biodiesel thus prepared are characterized as per ASTM D6751 and found comparable to mineral diesel. Steady state engine dynamometer test at 1800 rpm has been carried out to evaluate the performance and emission characteristics of a medium duty transportation DI diesel engine. Emission tests with all the fuel blends have also been carried out using European 13 MODE test (ECE R49).

Due to the demands of the market to increase efficiency and power density of large MW size gas engines, existing ignition schemes are gradually reaching their limits. These limitations initially triggered the development of laser ignition as an effective alternative, first only for gas engines and now for a much wider range of internal combustion engines revealing a number of immediate advantages like no electrode erosion or flame kernel quenching. Within this broad range investigation, laser plasmas were generated by ns Nd-YAG laser pulses and characterized by emission and Schlieren diagnostic methods. High-pressure chamber experiments with lean hydrogen- air mixtures were successfully performed and allowed the determination of essential parameters like minimum pulse energies at different ignition pressures and temperatures as well as at variable fuel air compositions. In this way, relevant parameters were acquired allowing estimation/ development of future laser ignition systems.

The scarce and rapidly depleting conventional petroleum resources have promoted research for alternative fuels for internal combustion engines. Among various possible options, fuels derived from vegetable oils present promising “greener” substitutes for fossil fuels. Vegetable oils due to their agricultural origin are able to reduce net CO2 emissions to the atmosphere along with import substitution of petroleum products. However, several operational and durability problems of using straight vegetable oils in diesel engines reported, which are because of their higher viscosity and low volatility compared to mineral diesel. In the present research, experiments were designed to study the effect of reducing Jatropha oil's viscosity by blending with mineral diesel, thereby eliminating its effect on combustion characteristics of the engine. In the present experimental research, vegetable oil (Jatropha Curcus) was used as substitute fuel.

The development of vehicles continues to be determined by increasingly stringent emissions standards including CO2 emissions and fuel consumption. To fulfill the simultaneous emission requirements for near zero pollutant and low CO2 levels, which are the challenges of future powertrains, many research studies are currently being carried out world over on new engine combustion process, such as Controlled Auto Ignition (CAI) for gasoline engines and Homogeneous Charge Compression Ignition (HCCI) for diesel engines. In HCCI combustion engine, ignition timing and combustion rates are dominated by physical and chemical properties of fuel/air/residual gas mixtures, boundary conditions including ambient temperature, pressure, and humidity and engine operating conditions such as load, speed etc.

Vegetable oils have energy content suitable to be used as compression ignition (CI) engine fuel. However, several operational and durability problems of using straight vegetable oils in CI engines are reported in the literature, which are primarily caused by their higher viscosity and low volatility compared to mineral diesel. The viscosity can be brought in acceptable range by (i) chemical process of transesterification, (ii) blending of oil with mineral diesel or (iii) by heating the vegetable oil using exhaust gas waste heat. Reduction of viscosity by blending or exhaust gas heating saves the chemical processing cost of transesterification. Present experimental investigations were carried out for evaluating combustion, performance and emission behavior of Jatropha oil blends in unheated conditions in a direct injection CI engine at different load and constant engine speed (1500 rpm).

Several experimental studies have been conducted for evaluating coefficient of friction and wear in simulated engine conditions using a piston ring segment and a liner piece rubbing against each other in reciprocating mode under load and lubricated conditions. In the present experimental investigation, a non-firing engine simulator has been developed in order to simulate engine conditions to a much closer extent. This machine can operate at similar linear speed, stroke, and load and can simulate almost similar engine operating conditions except firing pressures. This machine can also be used for comparing liners with different surface properties and the effects of surface texture on wear and oil consumption. One cylinder liner has been used for experimentation and the wear and surface properties behaviour were evaluated at several locations in the liner. Surface profile, roughness parameters are evaluated at several locations in the liner and at the top compression ring.

Thermal loading of diesel engine pistons has increased dramatically in recent years due to applications of various technologies to meet low emission and high power requirements. Control of piston temperatures by cooling of these pistons has become one of the determining factors in a successful engine design. The pistons are cooled by oil jets fired at the underside from the crankcase. Any undesirable piston temperature rise may lead to engine seizure due to piston warping. However, if the temperature at the underside of the piston, where the oil jet strikes the piston, is above the boiling point of the oil being used, it may contribute to the mist generation. This mist may significantly contribute to the non-tail pipe emissions in the form of unburnt hydrocarbons (UBHC). The problem of non-tail pipe emissions has unfortunately not been looked into so seriously, as the current stress of all the automobile manufacturers is on meeting the tail -pipe emission legislative limits.

In this study, 3D air-flow-field evolution in a single cylinder optical research engine was determined using tomographic particle imaging velocimetry (TPIV) at different engine speeds. Two directional projections of captured flow-field were pre-processed to reconstruct the 3D flow-field by using the MART (multiplicative algebraic reconstruction technique) algorithm. Ensemble average flow pattern was used to investigate the air-flow behavior inside the combustion chamber during the intake and compression strokes of an engine cycle. In-cylinder air-flow characteristics were significantly affected by the engine speed. Experimental results showed that high velocities generated during the first half of the intake stroke dissipated in later stages of the intake stroke. In-cylinder flow visualization indicated that large part of flow energy dissipated during the intake stroke and energy dissipation was the maximum near the end of the intake stroke.

Due to the increasingly stricter emission legislations and growing demand for lower fuel consumption, there have been significant efforts to improve combustion efficiency, while satisfying the emission requirements. Homogenous Charge Compression Ignition (HCCI) combustion offers significant efficiency improvements compared to conventional gasoline engines. However, due to the nature of HCCI, fully homogeneous charge HCCI combustion can be realized only in a limited operating range. Control of HCCI engines to obtain the desirable operation requires understanding of how different charge variables influence the cyclic variations in HCCI combustion. Under certain operating conditions, HCCI engines exhibit large cyclic variations in ignition timing. Cyclic variability ranging from stochastic to deterministic patterns can be observed. One important design goal for engine development is to minimize cyclic variability.

Homogeneous charge compression ignition (HCCI) is an advanced combustion concept that is developed as an alternative to diesel engines with higher thermal efficiency along with ultralow NOx and PM emissions. To study the performance of this novel technique, experiments were performed in a two cylinder engine, in which one cylinder is modified to operate in HCCI mode while other cylinder operates in conventional CI mode. The quality of homogeneous mixture of air and fuel is the key feature of HCCI combustion. Low volatility of diesel is a major hurdle in achieving HCCI combustion because it is difficult to make a homogeneous mixture of air and fuel. This problem is resolved by external mixture preparation technique in uses a dedicated diesel vaporizer with an electronic control system. All the injection parameters such as fuel quantity, fuel injection timing, injection delay etc., are controlled by the injection driver circuit.

Diesel engines are very efficient prime movers in their power range. Fuel is directly injected into the combustion chamber. Performance and emission characteristics of diesel engines are highly influenced by the fuel spray parameters and atomization of the injected fuel. As the emission regulations become stringent, it is very important to optimize the combustion in internal combustion engines for different fuels including alternative fuels. Spray visualization using optical techniques play a very important role to analyze macroscopic spray parameters and fuel atomization behavior. In the present experimental study, an important alternative CI engine fuel, Karanja oil and its blends with diesel have been investigated for their spray parameters and fuel atomization relative to mineral diesel. These parameters are different for the two fuels because of difference in the viscosity and density of the fuels.

The homogeneous charge compression ignition (HCCI) combustion process is capable of providing both high ‘diesel-like’ efficiencies and very low NOx and particulate emissions. However, among several technical challenges, controlling the combustion phasing, particularly during transients is a major issue, which must be resolved to exploit its commercial applications. This study is focused on the experimental investigations of behavior of combustion timing and other combustion parameters during startup and load transients. The study is conducted on a gasoline fuelled HCCI engine by varying intake air temperature and air-fuel ratio at different engine speeds. Port fuel injection technique is used for preparing homogeneous mixture of gasoline and air. For fueling startup transient test, fuel injection was turned off, and the engine was motored for several minutes until the fire-deck, intake and exhaust temperatures stabilized.

Laser is emerging as a strong contender as an alternative ignition source for internal combustion (IC) engines. Short laser pulses of few nanoseconds duration delivered by a Q-switched laser are focused by a lens inside the engine cylinder containing combustible fuel-air mixture. If the peak intensity at the focal point exceeds threshold intensity level, breakdown of combustible gases occurs, which leads to plasma formation. If the energy of the spark generated by plasma is high enough, the mixture ignites. In this investigation, laser ignition (LI) was performed in a single cylinder engine at constant speed and wide open throttle conditions using CNG as fuel. Combustion behavior was recorded using a high speed data acquisition system. For laser ignition of the engine, a laser spark plug was designed and manufactured. Laser spark plug consists of combination of lenses and optical windows.