Refine Your Search

Search Results

Viewing 1 to 10 of 10
Standard

Test Procedures for Shear Strength of Automotive Brake Pads and Brake Lining Assemblies

2007-08-21
HISTORICAL
J840_200708
This SAE Recommended Practice covers equipment capabilities and the test procedure to quantify and qualify the shear strength between the friction material and backing plate or brake shoe for automotive applications. This SAE Recommended Practice is applicable to: bonded drum brake linings; integrally molded disc brake pads; disc brake pads and backing plate assemblies using mechanical retention systems (MRS); coupons from drum brake shoes or disc brake pad assemblies. The test and its results are also useful for short, semi-quantitative verification of the bonding and molding process. This Recommended Practice is applicable during product and process development, product verification and quality control. This Recommended Practice does not replicate or predict actual vehicle performance or part durability.
Standard

Test Procedures for Shear Strength of Automotive Brake Pads and Brake Lining Assemblies

2017-11-15
CURRENT
J840_201711
This SAE Recommended Practice covers equipment capabilities and the test procedure to quantify and qualify the shear strength between the friction material and backing plate or brake shoe for automotive applications. This SAE Recommended Practice is applicable to: bonded drum brake linings; integrally molded disc brake pads; disc brake pads and backing plate assemblies using mechanical retention systems (MRS); coupons from drum brake shoes or disc brake pad assemblies. The test and its results are also useful for short, semi-quantitative verification of the bonding and molding process. This Recommended Practice is applicable during product and process development, product verification and quality control. This Recommended Practice does not replicate or predict actual vehicle performance or part durability.
Standard

Anti-Noise Brake Pads Shims: T-pull Test

2009-09-30
CURRENT
J2694_200909
This recommended practice covers the attachment of bonded anti-noise brake pad shims only. Mechanically attached shims (those without bonding) are not covered by this procedure.
Standard

Hardness of Brake Lining

2015-08-27
CURRENT
J2654_201508
Hardness measurements are used as a quality control check of the consistency of formulation and processing of brake linings. This hardness method is nondestructive. NOTE—This method is not a measure of friction level. The hardness and the range of hardness are characteristic of each formulation; therefore, the acceptable values and ranges must be established for each formulation and may be affected by processing. NOTE—The hardness of sintered powder metal lining is usually determined with Rockwell superficial hardness equipment. (See ASTM B 347)
Standard

Brake Lining Quality Test Procedure

2012-11-01
CURRENT
J661_201211
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
Standard

Swell, Growth, and Dimensional Stability of Friction Materials and Noise Insulators when Exposed to Elevated Temperatures

2013-02-13
CURRENT
J160_201302
This performance standard specifies a universal method of measuring the dimensional change of friction materials to determine the effects of temperature. The test applies to both, disc and drum type linings commonly used in hydraulic and air brake systems for automotive or commercial vehicle applications. This standard describes two main test procedures. Method A, where the friction material is in contact with a heated surface to simulate the heat input to the pad that occurs during actual usage. Method B uses an oven to heat the freestanding material and is an approximate procedure requiring less instrumentation. Method A is recommended for disc brake pad assemblies, noise insulators, or flat coupons; while Method B is recommended for curved drum brake linings.
Standard

Specific Gravity of Friction Material

2009-08-26
HISTORICAL
J380_200908
Specific gravity is a nondestructive test used as a quality control check of the consistency of formulation and processing of brake lining. The specific gravity and the range of specific gravity are peculiar to each formulation and, therefore, the acceptable values or range must be established for each formulation by the manufacturer. Specific gravity alone shows nothing about a materials in use performance. The specific gravity of sintered metal powder friction materials, particularly those which have steel backing members, is usually determined somewhat differently. Reference ASTM B 376.
Standard

Specific Gravity of Friction Material

2017-02-02
CURRENT
J380_201702
Specific gravity is a nondestructive test used as a quality control check of the consistency of formulation and processing of brake lining. The specific gravity and the range of specific gravity are peculiar to each formulation and, therefore, the acceptable values or range must be established for each formulation by the manufacturer. Specific gravity alone shows nothing about a materials in use performance. The specific gravity of sintered metal powder friction materials, particularly those which have steel backing members, is usually determined somewhat differently. Reference ASTM B 376.
Standard

Road Vehicles—Brake Linings—Compressibility Test Procedure

2006-12-18
HISTORICAL
J2468_200612
This SAE Standard specifies a method for testing and measuring the compressibility of friction materials and disc brake pad assemblies to be used in road vehicles. This SAE test method is consistent in intent with ISO 6310.
X