Refine Your Search

Search Results

Technical Paper

Application of a FIE Computer Model to an In-Line Pump-Based Injection System for Diesel Engines

1997-02-24
970348
A computer model simulating the flow in fuel injection systems has been used in order to investigate the fuel injection processes in an in-line pump-based fuel injection system for direct-injection diesel engines. The model is one-dimensional and it is based on the mass and momentum conservation equations for the simulation of the fuel flow and on the equilibrium of forces for the simulation of the mechanical movements of the valves present in the system. The fuel injection system tested comprised an in-line pump whose characteristics were examined by using as input the measured line pressure signal and by modeling the pump operation itself as well as the fuel flow through single- and two-stage injectors. For the validation of the model, extensive comparison with experimental data has been performed for a wide range of pump operating conditions.
Technical Paper

Analysis of the Flow in the Nozzle of a Vertical Multi-Hole Diesel Engine Injector

1998-02-23
980811
An enlarged transparent model of a six-hole vertical diesel injector has been manufactured in order to allow flow measurements inside the sac volume and the injection holes to be obtained using a combination of laser Doppler velocimetry (LDV) and the refractive index matching technique under steady state conditions. The measurement points were concentrated in the sac volume close to the entrance of the injection holes as well as inside them on a vertical plane passing through the axis of two injection holes for two different needle lifts. The velocity flow field was characterized in terms of the mean velocity and the turbulent intensity. The results revealed that, under certain conditions, cavitation may occur in the recirculation zone formed at the entrance to the hole since the pressure in this region can reach the value of the vapor pressure of the flowing liquid; this was found to strongly depend on the needle lift and eccentricity.
Technical Paper

Evaluation of Pump Design Parameters in Diesel Fuel Injection Systems

1995-02-01
950078
A computer model solving the 1-D flow in a typical fuel injection system for direct-injection diesel engines is presented. A Bosch distributor - type VE pump connected to four Stanadyne pencil - type nozzles has been used to validate the computer model over a wide range of operating conditions. Validation of the developed computer code has been performed for eight representative test cases. The predicted values which were compared with the experimental ones include the pumping chamber pressure, the line pressure, the needle lift and the injection rate. Results using as input the measured pumping chamber pressure are also presented in order to identify the error in the injection rate signal attributed to the difference between the simulated and the experimental pumping chamber pressure. In addition, the total fuel injection quantity for pump speeds between 500 and 2000 rpm and lever positions between 20% to 100% was calculated and compared with measurements.
Technical Paper

Transient Characteristics of Multi-Hole Diesel Sprays

1990-02-01
900480
The spatial and temporal characteristics of a diesel spray injected into the atmosphere through a multi-hole nozzle used in small DI Diesel engines have been investigated by laser techniques as a function of pump speed and load. The results showed that spray tip penetration and velocity depend on injection frequency rather than injected volume and the spray is asymmetric during the early and main part of the injection period. In the time/space domain different structures have been identified within the injection period, with the early injection period characterized by a well atomized cloud of droplets, the main period by the spray head and a dense core and the late injection period by the disintegrating dense core and the spray tail. IN DIRECT-INJECTION DIESEL ENGINES for passenger cars, fuel is injected through multi-hole nozzles at high pressure to promote mixing with the rapidly swirling air inside the combustion chamber.
Technical Paper

Transient Characteristics of Single-Hole Diesel Sprays

1989-02-01
890314
Diesel fuel was injected through a pintle nozzle into quiescent ambient air and the transient characteristics of the spray were examined as a function of injection pump speed. The laser-based techniques characterised the spray in terms of its transient structure, tip penetration, droplet axial mean and rms velocities and average droplet size. The results, when correlated with the fuel line pressure and nozzle exit conditions, revealed the presence of four regimes in the transient spray development: an early injection period representing the first stage of droplet formation, the main injection period associated with the formation and break up of a dense core and representing the second stage of droplet formation, a late injection period corresponding to the collapse of the dense core and a post injection period where, depending on the injection conditions, liquid ligaments and/or large droplets are present near the nozzle and may give rise to a third stage of droplet formation.
Technical Paper

Computer Simulation of Fuel Injection Systems for DI Diesel Engines

1992-10-01
922223
The continuity and momentum equations for a pump-pipe-nozzle fuel injection system have been solved by a computer simulation program employing both the Runge-Kutta method and the more widely used method of characteristics. This allows the prediction of fluid phenomena and the dynamics of the mechanical components based on the geometry of the FIE system. The simulation includes the effects of possible cavitation, system leakage as well as variations in fuel density and bulk modulus. The computer model has been made as flexible as possible by using a modular format and inputting the system parameters from external files or dialog boxes. Experimentation was done on a Bosch VE type distributor pump supplying a multi-hole type nozzle which allowed preliminary evaluation of the model by comparing the predicted and measured injection rates and line pressures over a range of pump speeds and loads.
Technical Paper

Analysis of Consecutive Fuel Injection Rate Signals Obtained by the Zeuch and Bosch Methods

1993-03-01
930921
The injection rate signals from a commercial diesel fuel injection system, based on a distributor pump driven by a DC motor, were characterised independently and consecutively by two injection rate meters based on the Zeuch and Bosch methods. The signals were first analysed in terms of their shot-to-shot variations over 64 consecutive injections and the correlations between needle lift and injection rate over a range of pump speeds and loads quantified by Fast Fourier Transform. A direct comparison of the injection rate signals on a cycle-resolved basis was achieved by connecting two consecutive injectors from the pump-line-nozzle injection system to a Bosch- and a Zeuch-based injection rate meters. The signals were acquired over a large number of injections in terms of mean and rms of the injected quantity, mean injection rate, maximum injection rate, average cumulative fuel injected and average injection duration.
Technical Paper

Spray Characteristics of Single- and Two-Spring Diesel Fuel Injectors

1993-03-01
930922
The spatial and temporal characteristics of the non-evaporating diesel sprays injected into the atmosphere through two pump-pipe-nozzle systems used in small DI diesel engines have been investigated by laser-single-beam deflection and phase-Doppler anemometry (PDA). The injectors used for these tests comprised a single-spring and a prototype two-spring multihole-type nozzle. The results provided quantitative information about the effect that the second spring exerts on injection duration and spray characteristics, i.e. it increases injection duration and, at the same time, improves fuel atomisation during the main injection period.
Technical Paper

Swirl Generation by Helical Ports

1989-02-01
890790
The effect of inlet port design on swirl generation has been investigated for four helical ports from production, prototype and research Dl diesel engines by analyzing experimentally measured steady flow velocity distributions at the inlet valve curtain area and comparing their swirl characteristics in terms of the calculated in-cylinder angular momentum components and swirl ratio under operating conditions.
Technical Paper

Effect of Inlet Parameters on the Flow Characteristics in a Four-Stroke Model Engine

1982-02-01
820750
The flow structure in a four-stroke model engine motored at 200 rpm with a compression ratio of 3.5 has been investigated. Ensemble-averaged axial and swirl mean and rms velocities have been obtained by laser-Doppler anemometry downstream of an axisymmetrically located single valve with 30 and 60 degree seat angles and various lifts, with and without induction swirl. In all cases, the intake-generated flow structure in the axial plane disappears by the time the inlet valve closes and results in nearly homogeneous turbulence during compression with levels of 0.5–0.7 times the mean piston speed. The swirling flow, however, which is induced by means of vanes, persists through the compression stroke, evolving from a spiralling motion early during intake into solid body type of rotation near TDC of compression, with associated swirl ratios increasing with valve lift.
Technical Paper

Three-Dimensional Flow Field in Four-Stroke Model Engines

1984-10-01
841360
Ensemble-averaged and in-cycle axial and swirl velocities have been measured by laser Doppler anemometry in the three-dimensional flow field of a four-stroke model engine motored at 200 rpm with a compression ratio of 6.7 and various cylinder head and piston geometries. The inlet configurations comprised an axisymmetric port with a shrouded valve and an off-centre port with two valve and swirl generating vane geometries. The piston configurations comprised flat, cylindrical and re-entrant axisymmetric piston-bowls. The results indicate that with the off-centre port a complex vortical flow pattern is generated during induction, which later either collapses in the absence of induction swirl or is transformed into a single rotating vortex in the transverse plane when swirl is present. The axisymmetric port with the shrouded valve gives rise to a double vortex structure and higher turbulence levels at TDC of compression compared to the off-centre port.
Technical Paper

Evaluation of the Predictive Capability of Diesel Nozzle Cavitation Models

2007-04-16
2007-01-0245
The predictive capability of Lagrangian and Eulerian multi-dimensional computational fluid dynamics models accounting for the onset and development of cavitation inside Diesel nozzle holes is assessed against experimental data. These include cavitation images available from a real-size six-hole mini-sac nozzle incorporating a transparent window as well as high-speed/CCD images and LDV measurements of the liquid velocity inside an identical large-scale fully transparent nozzle replica. Results are available for different cavitation numbers, which correspond to different cavitation regimes forming inside the injection hole. Discharge coefficient measurements for various real-size nozzles operating under realistic injection pressures are also compared and match well with models' predictions.
Technical Paper

Modeling of Pressure-Swirl Atomizers for GDI Engines

1999-03-01
1999-01-0500
A new simulation approach to the modeling of the whole fuel injection process within a common-rail fuel injection system for direct-injection gasoline engines, including the pressure-swirl atomizer and the conical hollow-cone spray formed at the nozzle exit, is presented. The flow development in the common-rail fuel injection system is simulated using an 1-D model which accounts for the wave dynamics within the system and predicts the actual injection pressure and injection rate throughout the nozzle. The details of the flow inside its various flow passages and the discharge hole of the pressure-swirl atomizer are investigated using a two-phase CFD model which calculates the location of the liquid-gas interface using the VOF method and estimates the transient formation of the liquid film developing on the walls of the discharge hole due to the centrifugal forces acting on the swirling fluid.
Technical Paper

Investigation of Cavitation in a Vertical Multi-Hole Injector

1999-03-01
1999-01-0524
An enlarged transparent model of a six-hole vertical diesel injector has been used to allow visualization of the flow at Reynolds and cavitation numbers matching those of real size injectors operating under normal Diesel engine conditions. The visualization system comprised a CCD camera, high-magnification lenses and a spark light source which allowed high-resolution images to be obtained. The flow conditions examined in terms of flow rates and pressures covered the range from low to full load of the real size injector while the needle lift position corresponded to that of full lift of the first- and second- stage in two-stage injectors. In addition, different values of needle eccentricity were tested in order to examine its effect on the cavitation structures within the injection holes.
Technical Paper

Modeling of Advanced High-Pressure Fuel Injection Systems for Passenger Car Diesel Engines

1999-03-01
1999-01-0910
A one-dimensional, transient and compressible flow model was used in order to simulate the flow and pressure distribution in advanced high-pressure fuel injection systems; these include electronic distributor-type pumps with either axial or radial plungers and a common-rail system. Experimental data for the line pressure, needle lift, injection rate and total fuel injection quantity obtained over a wide range of operating conditions (from idle to high speed/full load) were used to validate the model. The FIE system used for validation comprised an electronic high-pressure pump connected to two-stage injectors of different type including 6-hole vertical and 5-hole inclined conical-sac and VCO nozzles.
Technical Paper

Pressure-Swirl Atomizers for DISI Engines: Further Modeling and Experiments

2000-03-06
2000-01-1044
A combined two-phase CFD nozzle model and 1-D fuel injection system model is used to predict the flow development inside the discharge hole of a pressure-swirl atomizer connected to a common-rail based fuel injection system for DISI engines. The fuel injection model accounts for the transient pressure pulses developing inside the common-rail and the injector upstream of the nozzle tip and predicts the fuel injection rate through the nozzle. This is then used as input to a 3-D single-phase CFD model estimating the transient development of the swirl velocity inside the pressure-swirl atomizer, as a function of the geometric characteristics of nozzle.
Technical Paper

Spray Structure Generated by Multi-Hole Injectors for Gasoline Direct-Injection Engines

2007-04-16
2007-01-1417
The performance of multi-hole injectors designed for use in second-generation direct-injection gasoline engines has been characterised in a constant-volume chamber. Two types of multi-hole injector have been used: the first has 11 holes, with one hole on the axis of the injector and the rest around the axis at 30 degrees apart, and the second has 6 asymmetric holes located around the nozzle axis. Measurements of droplet axial and radial velocity components and their diameter were obtained using a 2-D phase Doppler anemometer (PDA) at injection pressures up to 120 bar, chamber pressures from atmospheric to 8 bar, and ambient temperatures. Complementary spray visualisation made use of a pulsed light and a CCD camera synchronised with the injection process.
Technical Paper

Cavitation in Real-Size Multi-Hole Diesel Injector Nozzles

2000-03-06
2000-01-1249
A production six-hole conical sac-type nozzle incorporating a quartz window in one of the injection holes has been used in order to visualize the flow under cavitating flow conditions. Simultaneous variation of both the injection and the back chamber pressures allowed images to be obtained at various cavitation and Reynolds numbers for two different fixed needle lifts corresponding to the first- and the second-stage lift of two-stage injectors. The flow visualization system was based on a fast and high resolution CCD camera equipped with high magnification lenses which allowed details of the various flow regimes formed inside the injection hole to be identified. From the obtained images both hole cavitation initiated at the top inlet corner of the hole as well as string cavitation formed inside the sac volume and entering into the hole from the bottom corner, were identified to occur at different cavitation and Reynolds numbers.
Technical Paper

Prediction of Liquid and Vapor Penetration of High Pressure Diesel Sprays

2006-04-03
2006-01-0242
A dense-particle Eulerian-Lagrangian stochastic methodology, able to resolve the dense spray formed at the nozzle exit has been applied to the simulation of evaporating diesel sprays. Local grid refinement at the area where the spray evolves allows use of cells having sizes from 0.6 down to 0.075mm. Mass, momentum and energy source terms between the two phases are spatially distributed to cells found within a distance from the droplet centre; this has allowed for grid-independent interaction between the Eulerian and the Lagrangian phases to be reached. Additionally, various models simulating the physical processes taking place during the development of sprays are considered. The cavitating nozzle flow is used to estimate the injection velocity of the liquid while its effect on the spray formation is considered through an atomisation model predicting the initial droplet size.
Technical Paper

Internal Flow and Cavitation in a Multi-Hole Injector for Gasoline Direct-Injection Engines

2007-04-16
2007-01-1405
A transparent enlarged model of a six-hole injector used in the development of emerging gasoline direct-injection engines was manufactured with full optical access. The working fluid was water circulating through the injector nozzle under steady-state flow conditions at different flow rates, pressures and needle positions. Simultaneous matching of the Reynolds and cavitation numbers has allowed direct comparison between the cavitation regimes present in real-size and enlarged nozzles. The experimental results from the model injector, as part of a research programme into second-generation direct-injection spark-ignition engines, are presented and discussed. The main objective of this investigation was to characterise the cavitation process in the sac volume and nozzle holes under different operating conditions. This has been achieved by visualizing the nozzle cavitation structures in two planes simultaneously using two synchronised high-speed cameras.
X