Search Results

The cruise control as one of promising vehicle active control has been receiving a considerable attention in recent years, so the related problems are discussed in this paper. Mathematical model of the engine under the steady state and general dynamics equation of the Continuously Variable Transmission(CVT) are given, the regulating principle of the operating state of the engine is analyzed, and the conjugate gradient method employed to solve the optimal control problem of the vehicle in the cruise control is described, so the operating state of the engine could be controlled. At end of paper, some results are provided to verify the approach based on the vehicular powertrain with a hydromechanical CVT.

Although Hydrostatic Transmission System (HTS) had been used in many places, such as machine tools, agriculture machinery, construction machinery, and vehicles, it had not been used in good performance. Twenty years ago many people began to design new hydrostatic transmission with higher efficiency. Hydrostatic Energy Storage Transmission System (HESTS) is one of new hydrostatic transmission system with higher efficiency. HESTS is more fit for being used in vehicle that is always running in undulating ground or starting and braking frequently. Construction of vehicular HESTS was analyzed, mathematical model of vehicular HESTS was established. The needed control strategies of vehicular HESTS were analyzed because there are many variables would be controlled in the new transmission system.

In this paper,the flywheel is considered to be linear elastic composition in accordance with its operating characteristic, mechanical and mathematical model are presented,the finite element method is employed to carry out the numerical analysis of steady and unsteady stresses within the high speed flywheel in the regenerative braking system of a city bus,and these provide the basis foŕ its structural modification and further rational design.

In this paper, the system identification theory and method using dynamic neural networks are presented, the multilayer feedforward networks employed, the backpropagation with adaptive learning rate algorithms proposed. Finally the comparision of network output with that of the hydrostatic drive system of secondary regulation is given, and output error, sum-squared error et al, or the results that embody the effect of system identification given sine input to it are provided.

In this paper, the intelligent control theory and method using neural networks are presented, the multilayer feedforward networks employed, the back propagation learning algorithm proposed. Finally the angular velocity control result of the hydrostatic drive system of secondary regulation with such type of control is provided. Relative studies revealed that the intelligent control for the system using neural networks can be effective.

For high levels autonomous driving functions, the Decision Layer often takes on more responsibility due to the requirement of facing more diverse and even rare conditions. It is very difficult to accurately find a safe and efficient lane change timing when autonomous vehicles encounter complex traffic flow and need to change lanes. The traditional method based on rules and experiences has the limitation that it is difficult to be taken into account all possible conditions. Therefore, this paper designs a lane-changing decision algorithm based on data-driven and machine learning, and uses the DQN (Deep Q Network) algorithm in Reinforcement Learning to determine the appropriate lane-changing timing and target lane. Firstly, the scene characteristics of the highway are analyzed, the input and output of the decision-making model are designated and the data from the Perception Layer are processed.

Centrifugal Pendulum Vibration Absorber (CPVA for short) is used to absorb torsional vibrations caused by the shifting motion of the engine. It is increasingly used in modern powertrains. In the research of the dynamic characteristics of the CPVA, it is necessary to obtain the real motion of the pendulum to compensate the fitting performance of mathematical model. The usual method is to install an angle sensor to measure the movement of the pendulum. On the one hand, the installation of the sensor will affect its movement to a certain extent, so that the measurement results do not match the actual motion. On the other hand, the motion of the pendulum is not only the rotational motion around the rotational axis of the CPVA rotor, but also has translation relative to it. As a result, it is difficult to obtain accurate motion only by the angle sensor. We proposed a non-contact centrifugal pendulum motion measurement method.

Subframe is an important part of automobile chassis, which is connected with body, suspension control arm, powertrain mount, etc. The dynamic stiffness value of the connection point is an important performance index of the subframe, which affects the vibration of the vehicle body. This paper introduces the basic concept and related theory of dynamic stiffness, derives the theoretical formula of dynamic stiffness, and analyzes the frequency response of the key points of the subframe. In view of the fact that the dynamic stiffness of the subframe of a certain vehicle model is not up to the standard at some connection points, the dynamic stiffness CAE simulation analysis is carried out to determine the frequency range of insufficient dynamic stiffness and the connection points that need to be optimized.

For the DCC (Dynamic Chassis Control) system, in addition to the requirement of ride and comfort, it is also necessary to consider the requirement of handling and stability, and these two requirements are often not met at the same time. This poses a great challenge to the design of the controller, especially in the face of complex working conditions. In order to solve this problem, this paper proposes a comprehensive DCC controller that considers road roughness class recognition. Firstly, a quarter vehicle model is established, the road surface roughness is calculated from the vertical acceleration of the wheels measured by the sensors. Then we calculate the autocorrelation function and the Fourier transform to estimate the PSD (Power Spectral Density) to get the road roughness class. Then control algorithms are designed for the vertical motion control, roll control and pitch control.

The traditional automotive torque converter (TC) is equipped with a single-blade stator, at the suction side of which there is an apparent boundary layer separation at stalling condition because of its large impending angle. The separation flow behind the suction side of stator blade is found to create large area of low-energy flow which blocks effective flow passage area, produces more energy losses, decreases impeller torque capacity and transmission efficiency. It is found effective to suppress the boundary layer separation by separating the original single-blade stator into a primary and a secondary part. The gap between them guides high-energy flow at the pressurized side of the primary blade to the suction side of the secondary one, which helps to make boundary layer flow stable. As a result, the impeller torque capacity and torque ratio at low-speed ratio increase tremendously at the cost of little drop of maximum efficiency.

As a newly designed hybrid transmission, DHT (Dedicated Hybrid Transmission) owns the advantages of compact structure, multi-modes and excellent comprehensive performance. Compared with the traditional add-on hybrid transmission with one single motor, DHT uses one independent generator for engine starting and speed adjusting which can be largely improve the driving performance in the mode changing process. Based on the series-parallel DHT with wet clutch for power coupling, this paper firstly analyses the power coupling clutch device functionalities from the power flow viewpoint under normal and limp home condition. And for the changing process from series to parallel mode, a clutch coordination control strategy is designed by combining generator fast speed adjusting with clutch accurately pressure controlling to fulfill the fast driver intension response and clutch protection.