Search Results

Standard

Materials for Plastic Pistons for Hydraulic Disc Brake Cylinders

2001-05-14

HISTORICAL

J1568_200105

The materials defined by this SAE Standard are glass-fiber-reinforced, mineral-filled phenolic molding compounds suitable for compression molding. Preforms may be radio frequency preheated or screw preheated slugs. Compound for use in hydraulic disc brake caliper pistons.

Standard

Shelf Storage of Hydraulic Brake Components

1998-01-01

HISTORICAL

J1825_199801

This SAE Information Report is the listing of recommendations for shelf storage for hydraulic brake components. Included in brake components are wheel cylinders, master cylinders, combination valves, and disc brake caliper assemblies. This document is not a specification. This document embodies the analyses and experiences of many users and manufacturers. Where specific manufacturers' recommendations are made, those recommendations shall supersede the recommendations of this document. This document lists the successful procedures and practices associated with brake components based on long experience of a wide cross section of manufacturers and users. The practices are expected to be applied to all brake components where SAE standards are applicable.

Standard

Shelf Storage of Hydraulic Brake Components

2005-01-05

HISTORICAL

J1825_200501

This SAE Information Report is the listing of recommendations for shelf storage for hydraulic brake components. Included in brake components are wheel cylinders, master cylinders, combination valves, and disc brake caliper assemblies. This document is not a specification. This document embodies the analyses and experiences of many users and manufacturers. Where specific manufacturers' recommendations are made, those recommendations shall supersede the recommendations of this document. This document lists the successful procedures and practices associated with brake components based on long experience of a wide cross section of manufacturers and users. The practices are expected to be applied to all brake components where SAE standards are applicable.

Standard

RUBBER CUPS FOR HYDRAULIC ACTUATING CYLINDERS

1997-07-01

HISTORICAL

J1601_199707

These specifications cover molded cups 51 mm (2 in) in diameter and under, compounded from high temperature resistant rubber for use in hydraulic actuating cylinders employing motor vehicle brake fluid conforming to the requirements specified in SAE J1703 and SAE J1705. These specifications cover the performance tests of hydraulic brake cups under specified conditions and do not include requirements relating to chemical composition, tensile strength, and elongation of the rubber compound. Disc brake seals are not covered by this document.

Standard

RUBBER CUPS FOR HYDRAULIC ACTUATING CYLINDERS

1990-11-26

HISTORICAL

J1601_199011

These specifications cover molded cups 51 mm (2 in) in diameter and under, compounded from high temperature resistant rubber for use in hydraulic actuating cylinders employing motor vehicle brake fluid conforming to the requirements specified in SAE J1703 and SAE J1705. These specifications cover the performance tests of hydraulic brake cups under specified conditions and do not include requirements relating to chemical composition, tensile strength, and elongation of the rubber compound. Disc brake seals are not covered by this document.

Standard

RUBBER BOOTS FOR DRUM-TYPE HYDRAULIC BRAKE WHEEL CYLINDERS

1989-10-01

HISTORICAL

J1604_198910

This document covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of -40 to + 120 ± 2°C (-40 to +248 ± 3.6°F).

Standard

RUBBER BOOTS FOR DRUM-TYPE HYDRAULIC BRAKE WHEEL CYLINDERS

1995-01-01

HISTORICAL

J1604_199501

This SAE Standard covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of -40 to +120 °C ± 2 °C (-40 to + 248 °F ± 3.6 °F).

Standard

Rubber Boots for Drum-Type Hydraulic Brake Wheel Cylinders

2015-12-17

CURRENT

J1604_201512

This SAE Standard covers molded rubber boots used as end closures on drum-type wheel brake actuating cylinders to prevent the entrance of dirt and moisture, which could cause corrosion and otherwise impair wheel brake operation. The document includes performance tests of brake cylinder boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition, tensile strength, or elongation of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operation in a temperature range of −40 to +120 °C ± 2 °C (−40 to + 248 °F ± 3.6 °F).

Standard

RUBBER SEALS FOR HYDRAULIC DISC BRAKE CYLINDERS

1990-06-01

HISTORICAL

J1603_199006

This SAE Standard describes the performance and part requirements for elastomeric seals used in highway vehicle disc brake calipers. Seals covered by this specification may be the solid section type (square, rectangular, O-ring, etc.) mounted stationary in the cylinder bore or on the movable piston.

Standard

AUTOMOTIVE HYDRAULIC BRAKE SYSTEM - METRIC TUBE CONNECTIONS

1989-05-01

HISTORICAL

J1290_198905

This standard documents dimensional metric specifications for hydraulic brake system tubing with flared ends, threaded ports, and male tube nuts for the interconnection of major components in automotive hydraulic brake systems. The purpose of this document is to recommend preferred metrically dimensioned components (including alternative choices), that are intended to be functionally compatible with International Organization for Standardization Specification, ISO 4038-1977 (E). Some applications may require sizes of forms other than those shown herein, and this document does not preclude such other details when they are required.

Standard

Hydraulic Wheel Cylinders for Automotive Drum Brakes

2006-08-16

HISTORICAL

J101_200608

This document specifies minimum performance and durability requirements for satisfactory vehicle usage, and it is applicable to wheel cylinder assemblies from commercial production, after production shipment, shelf storage, and remanufacture (factory rebuild).

Standard

HYDRAULIC WHEEL CYLINDERS FOR AUTOMOTIVE DRUM BRAKES

1973-03-01

HISTORICAL

J101A_197303

The standard specifies minimum performance and durability requirements for satisfactory vehicle usage, and it is applicable to wheel cylinder assemblies from commercial production, after production shipment, shelf storage, and remanufacture (factory rebuild).

Standard

HYDRAULIC WHEEL CYLINDERS FOR AUTOMOTIVE DRUM BRAKES

1989-12-01

HISTORICAL

J101_198912

This document specifies minimum performance and durability requirements for satisfactory vehicle usage, and it is applicable to wheel cylinder assemblies from commercial production, after production shipment, shelf storage, and remanufacture (factory rebuild).

Standard

HYDRAULIC VALVES FOR MOTOR VEHICLE BRAKE SYSTEMS TEST PROCEDURE

1977-05-01

HISTORICAL

J1118_197705

The Recommended Practice specifies the test procedure to assure valve assemblies which are satisfactory for vehicle usage, and it is applicable to new valve assemblies from commercial production, and remanfacture (factory rebuild). The minimum performance and durability requirements are specified in SAE J1137, Hydraulic Valves for Motor Vehicle Brake Systems-Performance Requirements.

Standard

Rubber Dust Boots for the Hydraulic Disk Brake Piston

2012-04-30

CURRENT

J1570_201204

This SAE Standard covers molded rubber boots used on disc brake pistons to prevent the entrance of dirt and moisture which could cause corrosion and otherwise impair caliper operation. The specification includes performance tests of brake piston boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition or physical properties of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operating in a temperature range of -40 to + 120 °C ± 2 °C (-40 to + 248 °F ± 3.6 °F).

Standard

Rubber Dust Boots for the Hydraulic Disk Brake Piston

2008-05-13

HISTORICAL

J1570_200805

This SAE Standard covers molded rubber boots used on disc brake pistons to prevent the entrance of dirt and moisture which could cause corrosion and otherwise impair caliper operation. The specification includes performance tests of brake piston boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition or physical properties of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operating in a temperature range of −40 to + 120 °C ± 2 °C (−40 to + 248 °F ± 3.6 °F).

Standard

RUBBER DUST BOOTS FOR THE HYDRAULIC DISC BRAKE PISTON

1988-10-01

HISTORICAL

J1570_198810

This specification covers molded rubber boots used on disc brake pistons to prevent the entrance of dirt and moisture which could cause corrosion and otherwise impair caliper operation. The specification includes performance tests of brake piston boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition or physical properties of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operating in a temperature range of -40 to +120 ±2°C (-40 to +248 ±3.6°F).