Search Results

Standard

Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers

2006-03-27

HISTORICAL

J2631_200603

This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.

Standard

Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers

2011-10-25

CURRENT

J2631_201110

This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.

Standard

Test Procedures for Non-SAE Hydraulic Hoses

2001-03-14

HISTORICAL

J2545_200103

This SAE Recommended Practice identifies test procedures and parameters which may be used to evaluate, qualify and inspect non-SAE hydraulic hoses or other hose constructions which do not conform to any established ISO or national standards defining hydraulic hoses. (Non-SAE hydraulic hoses are defined as those which do not conform to the categories listed in SAE J517.) It is not intended for evaluating fluoropolymer lined hose constructions or hose constructions with working pressures above 86 MPa.

Standard

Test Procedures for Non-SAE Hydraulic Hoses

2009-03-31

HISTORICAL

J2545_200903

This SAE Recommended Practice identifies test procedures and parameters which may be used to evaluate, qualify and inspect non-SAE hydraulic hoses or other hose constructions which do not conform to any established ISO or national standards defining hydraulic hoses. (Non-SAE hydraulic hoses are defined as those which do not conform to the categories listed in SAE J517.) It is not intended for evaluating fluoropolymer lined hose constructions or hose constructions with working pressures above 86 MPa.

Standard

Test Procedures for Non-SAE Hydraulic Hoses

2014-06-04

HISTORICAL

J2545_201406

This SAE Recommended Practice identifies test procedures and parameters which may be used to evaluate, qualify and inspect non-SAE hydraulic hoses or other hose constructions which do not conform to any established ISO or national standards defining hydraulic hoses. (Non-SAE hydraulic hoses are defined as those which do not conform to the categories listed in SAE J517.) It is not intended for evaluating fluoropolymer lined hose constructions or hose constructions with working pressures above 86 MPa.

Standard

Test Procedures for Non-SAE Hydraulic Hoses

2021-04-14

CURRENT

J2545_202104

This SAE Recommended Practice identifies test procedures and parameters which may be used to evaluate, qualify and inspect non-SAE hydraulic hoses or other hose constructions which do not conform to any established ISO or national standards defining hydraulic hoses. (Non-SAE hydraulic hoses are defined as those which do not conform to the categories listed in SAE J517.) It is not intended for evaluating fluoropolymer lined hose constructions or hose constructions with working pressures above 86 MPa.

Standard

Hydraulic Hose Fitting for Marine Applications

2014-06-05

CURRENT

J1475_201406

This SAE Standard covers general and performance specifications for hydraulic hose fittings of the styles, types, and classes defined in Section 3 and used in conjunction with nonmetallic flexible hoses for marine applications. This document does not ensure compatibility between manufacturers of hydraulic hose and hydraulic hose fittings. Compatibility is the responsibility of the hydraulic hose assembly manufacturer.

Standard

HYDRAULIC HOSE FITTINGS FOR MARINE APPLICATIONS

1993-07-01

HISTORICAL

J1475_199307

This SAE Standard covers general and performance specifications for hydraulic hose fittings of the styles, types, and classes defined in 2.2 and used in conjunction with nonmetallic flexible hose used in marine applications. In addition to the requirements of this document, the hose fittings shall meet the general and dimensional requirements of SAE J516. Other styles, types, and classes of fittings may be used provided they meet the general requirements of Sections 3 through 9. Four-bolt split flange type clamp halves are not within the scope of this document and are covered under SAE J518. This document does not insure compatibility between manufacturers of hydraulic hose and hydraulic hose fittings. Compatibility is the responsibility of the hydraulic hose assembly manufacturer.

Standard

CUMULATIVE DAMAGE ANALYSIS FOR HYDRAULIC HOSE ASSEMBLIES

1988-10-01

HISTORICAL

J1927_198810

Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

2009-03-27

HISTORICAL

J1927_200903

This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.

Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

2001-03-14

HISTORICAL

J1927_200103

This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.

Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

2014-06-04

CURRENT

J1927_201406

This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.

Standard

TESTS AND PROCEDURES FOR HIGH TEMPERATURE TRANSMISSION OIL HOSE, ENGINE LUBRICATING OIL HOSE, AND HOSE ASSEMBLIES

1990-06-01

HISTORICAL

J1019_199006

This SAE Standard is intended to establish uniform methods for testing and evaluation of hose and hose assemblies for use in high temperature transmission oil systems and high temperature lubricating oil systems using petroleum base oils within a temperature range of −40 ° to 150 °C (−40 ° to 302 °F) and a maximum working pressure of 1.5 MPa (217 psi). Hose construction, dimensions, identification, and hose fitting configurations shall be agreed upon by the supplier and user.

Standard

Tests and Procedures for High Temperature Transmission Oil Hose, Engine Lubricating Oil Hose, and Hose Assemblies

2007-09-17

CURRENT

J1019_200709

This SAE Standard is intended to establish uniform methods for testing and evaluation of hose and hose assemblies for use in high temperature transmission oil systems and high temperature lubricating oil systems using petroleum base oils within a temperature range of -40 to 150 degrees C (-40 to 302 degrees F) and a maximum working pressure of 1.5 MPa (217 psi). Hose construction, dimensions, identification, and hose fitting configurations shall be agreed upon by the supplier and user.

Standard

TESTS AND PROCEDURES FOR HIGH-TEMPERATURE TRANSMISSION OIL HOSE, LUBRICATING OIL HOSE AND HOSE ASSEMBLIES

1986-05-01

HISTORICAL

J1019_198605

This standard is intended to establish uniform methods for testing and evaluation of hose and hose assemblies for use in: high-temperature transmission oil systems and high-temperature lubricating oil systems.

Standard

Recommended Practices for Hydraulic Hose Assemblies

2009-02-17

HISTORICAL

J1273_200902

SAE J1273 provides guidelines for selection, routing, fabrication, installation, replacement, maintenance, and storage of hose and hose assemblies for hydraulic fluid-power systems. Many of these SAE Recommended Practices also may be suitable for other hoses and systems.

Standard

Recommended Practices for Hydraulic Hose Assemblies

2014-09-17

HISTORICAL

J1273_201409

SAE J1273 provides guidelines for selection, routing, fabrication, installation, replacement, maintenance, and storage of hose and hose assemblies for hydraulic fluid-power systems. Many of these SAE Recommended Practices also may be suitable for other hoses and systems.

Standard

Recommended Practices for Hydraulic Hose Assemblies

2021-10-28

CURRENT

J1273_202110

SAE J1273 provides guidelines for selection, routing, fabrication, installation, replacement, maintenance, and storage of hose and hose assemblies for hydraulic fluid-power systems. Many of these SAE Recommended Practices also may be suitable for other hoses and systems.

Standard

Recommended Practices for Hydraulic Hose Assemblies

2019-10-31

HISTORICAL

J1273_201910

SAE J1273 provides guidelines for selection, routing, fabrication, installation, replacement, maintenance, and storage of hose and hose assemblies for hydraulic fluid-power systems. Many of these SAE Recommended Practices also may be suitable for other hoses and systems.

Standard

Recommended Practices for Hydraulic Hose Assemblies

2020-09-01

HISTORICAL

J1273_202009

SAE J1273 provides guidelines for selection, routing, fabrication, installation, replacement, maintenance, and storage of hose and hose assemblies for hydraulic fluid-power systems. Many of these SAE Recommended Practices also may be suitable for other hoses and systems.