Refine Your Search

Search Results

Standard

Tests and Procedures for High Temperature Transmission Oil Hose, Engine Lubricating Oil Hose, and Hose Assemblies

1986-05-01
HISTORICAL
J1019_198605
This SAE Standard is intended to establish uniform methods for testing and evaluation of hose and hose assemblies for use in high temperature transmission oil systems and high temperature lubricating oil systems using petroleum base oils within a temperature range of -40 to 150 degrees C (-40 to 302 degrees F) and a maximum working pressure of 1.5 MPa (217 psi). Hose construction, dimensions, identification, and hose fitting configurations shall be agreed upon by the supplier and user.
Standard

Tests and Procedures for High Temperature Transmission Oil Hose, Engine Lubricating Oil Hose, and Hose Assemblies

1990-06-01
HISTORICAL
J1019_199006
This SAE Standard is intended to establish uniform methods for testing and evaluation of hose and hose assemblies for use in high temperature transmission oil systems and high temperature lubricating oil systems using petroleum base oils within a temperature range of -40 to 150 degrees C (-40 to 302 degrees F) and a maximum working pressure of 1.5 MPa (217 psi). Hose construction, dimensions, identification, and hose fitting configurations shall be agreed upon by the supplier and user.
Standard

Tests and Procedures for High Temperature Transmission Oil Hose, Engine Lubricating Oil Hose, and Hose Assemblies

2007-09-17
CURRENT
J1019_200709
This SAE Standard is intended to establish uniform methods for testing and evaluation of hose and hose assemblies for use in high temperature transmission oil systems and high temperature lubricating oil systems using petroleum base oils within a temperature range of -40 to 150 degrees C (-40 to 302 degrees F) and a maximum working pressure of 1.5 MPa (217 psi). Hose construction, dimensions, identification, and hose fitting configurations shall be agreed upon by the supplier and user.
Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

1988-10-01
HISTORICAL
J1927_198810
This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.
Standard

Cumulative Damage Analysis for Hydraulic Hose Assemblies

2014-06-04
CURRENT
J1927_201406
This SAE Information Report is intended to provide the hydraulic system analyst with a procedure which will assist in the selection and use of high-pressure wire reinforced hydraulic hose assemblies. Many construction, agricultural, industrial, or commercial equipment systems utilize hydraulic hose assemblies that are subjected to irregular cyclic pressure variations (cannot be approximated by a constant amplitude pressure cycle). This document relates damage done by pressure cycles with the pressure-life performance curve for the hose assembly being evaluated, using a linear damage rule to predict fatigue life similar to that used for predicting metal fatigue life. More detailed information on the subject may be found in SAE Paper No. 880713. The accuracy of cumulative damage calculations is directly related to proper measurement of the service pressure history and pressure-life performance for the hose assembly being evaluated.
Standard

Optional Impulse Test Procedures for Hydraulic Hose Assemblies

2003-12-19
HISTORICAL
J1405_200312
The procedures contained in this SAE Recommended Practice have been developed to establish uniform methods for impulse testing of hydraulic hose assemblies under special conditions not specified in SAE J343 for SAE J517 hoses. Basic impulse test parameters are to be in accordance with SAE J343 except as modified in this document.
Standard

Optional Impulse Test Procedures for Hydraulic Hose Assemblies

1990-06-18
HISTORICAL
J1405_199006
The procedures contained in this SAE Recommended Practice have been developed to establish uniform methods for impulse testing of hydraulic hose assemblies under special conditions not specified in SAE J343 for SAE J517 hoses. Basic impulse test parameters are to be in accordance with SAE J343 except as modified in this document.
Standard

Optional Test Procedures for Hydraulic Hose Assemblies

1986-05-01
HISTORICAL
J1405_198605
The procedures contained in this SAE Recommended Practice have been developed to establish uniform methods for impulse and high temperature circulation testing of hydraulic hose assemblies under special conditions not specified in SAE J343 for SAE J517 hoses. Basic test procedures are to be in accordance with SAE J343 except as modified in this document.
Standard

Optional Test Procedures for Hydraulic Hose Assemblies

2017-01-04
CURRENT
J1405_201701
The procedures contained in this SAE Recommended Practice have been developed to establish uniform methods for impulse and high temperature circulation testing of hydraulic hose assemblies under special conditions not specified in SAE J343 for SAE J517 hoses.Basic test procedures are to be in accordance with SAE J343 except as modified in this document.
Standard

Optional Test Procedures for Hydraulic Hose Assemblies

2012-05-08
HISTORICAL
J1405_201205
The procedures contained in this SAE Recommended Practice have been developed to establish uniform methods for impulse and high temperature circulation testing of hydraulic hose assemblies under special conditions not specified in SAE J343 for SAE J517 hoses.Basic test procedures are to be in accordance with SAE J343 except as modified in this document.
Standard

Optional Test Procedures for Hydraulic Hose Assemblies

2005-11-02
HISTORICAL
J1405_200511
The procedures contained in this SAE Recommended Practice have been developed to establish uniform methods for impulse testing of hydraulic hose assemblies under special conditions not specified in SAE J343 for SAE J517 hoses. Basic impulse test parameters are to be in accordance with SAE J343 except as modified in this document.
Standard

Defining Hydraulic Oil Compatibility With Hydraulic Hose Elastomers

2006-03-27
HISTORICAL
J2631_200603
This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property-Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.
Standard

Defining Hydraulic Oil Compatibility with Hydraulic Hose Elastomers

2011-10-25
CURRENT
J2631_201110
This SAE Information Report is intended to provide the hydraulic oil manufacturer and hydraulic equipment manufacturer with information that can be used predicting the relative impact that non petroleum based hydraulic oils may have on the hose elastomers in the existing system. This document contains the information necessary to perform the tests using standard elastomer formulations, representative of material used in hydraulic hose. The test methods used are defined within ASTM D471, standard test method for Rubber Property—Effect of Liquids. The physical properties measured, are volume swell, tensile strength, percent elongation, shore A hardness and load at 100% elongation. The properties were measured, after immersion, at 72 hours, 168 hours, 336 hours, 504 hours, 672 hours, 840 hours, and 1008 hours and the percent calculated as change from the unaged properties. The detail of the testing process is described in the following report.
Standard

Optional Test Procedures for Hydraulic Hose Assemblies

1979-01-01
HISTORICAL
J1405_197901
The procedures contained in this SAE Recommended Practice have been developed to establish uniform methods for impulse and high temperature circulation testing of hydraulic hose assemblies under special conditions not specified in SAE J343 for SAE J517 hoses. Basic test procedures are to be in accordance with SAE J343 except as modified in this document.
Standard

Test Procedures for Non-SAE Hydraulic Hoses

2014-06-04
CURRENT
J2545_201406
This SAE Recommended Practice identifies test procedures and parameters which may be used to evaluate, qualify and inspect non-SAE hydraulic hoses or other hose constructions which do not conform to any established ISO or national standards defining hydraulic hoses. (Non-SAE hydraulic hoses are defined as those which do not conform to the categories listed in SAE J517.) It is not intended for evaluating fluoropolymer lined hose constructions or hose constructions with working pressures above 86 MPa.
Standard

Push-On Hose and Mating Hose Fittings

2014-06-06
CURRENT
J2552_201406
SAE J2552 provides limited, dimensional and general performance requirements for low pressure, field attachable, push-on hose and their mating hose fittings. The intended application is for fluid and pneumatic power used with petroleum base hydraulic fluids, lube oils, water glycols and air, within the temperature ranges listed in Table 1. The maximum working pressure is 1.7 MPa (see Table 2). For air applications the maximum working pressure is at 0.7 MPa. Hose and hose fittings are manufactured within certain dimensions with tolerance ranges in order to provide the proper gripping and sealing. SAE J2552 hose from one manufacturer may not be compatible with SAE J2552 hose fittings supplied by another manufacturer. It is the responsibility of the fabricator to always follow the manufacturers’ instructions for proper preparation and fabrication of hose assemblies.
Standard

Push-On Hose and Mating Hose Fittings

2009-03-04
HISTORICAL
J2552_200903
This SAE standard provides limited, dimensional and general performance requirements for low pressure, field attachable, push-on hose and their mating hose fittings. The intended application is for fluid and pneumatic power used with petroleum base hydraulic fluids, lube oils, water glycols and air, within the temperature ranges listed in Table 1. The maximum working pressure is 1.7 MPa (see Table 2). For air applications the maximum working pressure is at 0.7 MPa. Hose and hose fittings are manufactured within certain dimensions with tolerance ranges in order to provide the proper gripping and sealing. SAE J2552 hose from one manufacturer may not be compatible with J2552 hose fittings supplied by another manufacturer. It is the responsibility of the fabricator to consult the manufacturers' written assembly instructions or the manufacturers directly before intermixing hose and hose fittings from two manufacturers.
Standard

Qualified Hoses for Marine Applications

1995-05-01
HISTORICAL
J1942/1_199505
Effective August 28, 1991, the SAE replaced the USCG as the listing agency for Marine Hose Assemblies. The previous USCG list was discontinued as of December 31, 1992, and is being replaced by this SAE listing, J1942-1. All products appearing on the USCG list as of December 31, 1992, may be carried over to the SAE J1942-1 provided they meet the new test requirements listed in SAE J1942. If your products comply, you may retain your listings with no additional testing. (Please note that the USCG has the authority to request and inspect your test results at their discretion.) The following list consists of hose data provided as of May 2003, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25(c). Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting.
Standard

Qualified Hoses for Marine Applications

1997-05-01
HISTORICAL
J1942/1_199705
Effective August 28, 1991, the SAE replaced the USCG as the listing agency for Marine Hose Assemblies. The previous USCG list was discontinued as of December 31, 1992, and is being replaced by this SAE listing, J1942-1. All products appearing on the USCG list as of December 31, 1992, may be carried over to the SAE J1942-1 proved they meet the new test requirements listed in SAE J 1942. If your products comply, you may retain your listings with no additional testing. (Please not that the USCG has the authority to request and inspect your test results at their discretion.) The following list consists of hose data provided as of April 30, 19998, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended to usage under 46 CFR 56.60-25(c). Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting.
Standard

Qualified Hoses for Marine Applications

1994-05-01
HISTORICAL
J1942/1_199405
Effective August 28, 1991, the SAE replaced the USCG as the listing agency for Marine Hose Assemblies. The previous USCG list was discontinued as of December 31, 1992, and is being replaced by this SAE listing, J1942-1. All products appearing on the USCG list as of December 31, 1992, may be carried over to the SAE J1942-1 provided they meet the new test requirements listed in SAE J1942. If your products comply, you may retain your listings with no additional testing. (Please note that the USCG has the authority to request and inspect your test results at their discretion.) The following list consists of hose data provided as of May 2003, and is for convenience in determining acceptability of nonmetallic flexible hose assemblies intended for usage under 46 CFR 56.60-25(c). Where the maximum allowable working pressure (MAWP) or type of fitting is not specified, use the manufacturer's recommended MAWP or type of fitting.
X