Refine Your Search

Search Results

Standard

Fitting—O-Ring Face Seal

2009-01-13
CURRENT
J1453_200901
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Connections for Fluid Power and General Use--Ports and Stud Ends with ISO 261 Metric Threads and O-Ring Sealing, Part 3: Light-Duty (L Series) Stud Ends--Dimensions, Design, Test Methods, and Requirements

2007-12-21
CURRENT
J2244/3_200712
This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable light-duty (L series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 40 MPa for nonadjustable stud ends and 31.5 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydraulic fluid power applications. Conformance to the dimensional information in this SAE Standard does not guarantee rated performance.
Standard

Connections for Fluid Power and General Use--Ports and Stud Ends With Iso 261 Threads and O-Ring Sealing--Part 4: Heavy-Duty (S Series) External Hex Port Plugs--Dimensions, Design, Test Methods, and Requirements

1997-01-01
HISTORICAL
J2244/4_199701
This part of SAE J2244 specifices dimensions, performance requirements, and test procedures for metric external hex O-rings port plugs. Port plugs in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydrualic fluid power applications. Conformance to the dimensional information in this document does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance ratings.
Standard

Connections for Fluid Power and General Use--Ports and Stud Ends with ISO 261 Threads and O-Ring Sealing--Part 4: Heavy-Duty (S Series) External Hex Port Plugs--Dimensions, Design, Test Methods, and Requirements

2007-12-21
CURRENT
J2244/4_200712
This part of SAE J2244 specifices dimensions, performance requirements, and test procedures for metric external hex O-rings port plugs. Port plugs in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydrualic fluid power applications. Conformance to the dimensional information in this document does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance ratings.
Standard

Connections for Fluid Power and General Use-Ports and Stud Ends With Iso 261 Threads and O-Ring Sealing Part 2: Heavy-Duty (S Series) Stud Ends- Dimensions, Design, Test Methods, and Requirements

1991-12-01
HISTORICAL
J2244/2_199112
This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable heavy-duty (S Series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa for nonadjustable stud ends and 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used for new designs in hydraulic fluid power applications. Conformance to the dimensional information in this standard does not guarantee rated performance.
Standard

Connections for Fluid Power and General Use--Ports and Stud Ends with ISO 261 Threads and O-Ring Sealing Part 2: Heavy-Duty (S Series) Stud Ends--Dimensions, Design, Test Methods, and Requirements

2007-12-21
CURRENT
J2244/2_200712
This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable heavy-duty (S Series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa for nonadjustable stud ends and 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used for new designs in hydraulic fluid power applications. Conformance to the dimensional information in this standard does not guarantee rated performance.
Standard

Connections for Fluid Power and General Use Ports and Stud Ends with ISO 261 Metric Threads and O-Ring Sealing, Part 3: Light-Duty (L Series) Stud Ends Dimensions, Design, Test Methods, and Requirements

1998-06-01
HISTORICAL
J2244/3_199806
This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable light-duty (L series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 40 MPa for nonadjustable stud ends and 31.5 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydraulic fluid power applications. Conformance to the dimensional information in this SAE Standard does not guarantee rated performance.
Standard

Connections for Fluid Power and General Use--Ports and Stud Ends With Iso 261 Threads and O-Ring Sealing Part 3: Light-Duty (L Series) Stud End--Dimensions, Design, Test Methods, and Requirements

1996-04-01
HISTORICAL
J2244/3_199604
This part of SAE J2244 specifies dimensions, performance requirements, and test procedures for metric adjustable and nonadjustable light-duty (L series) stud ends and O-rings. Stud ends in accordance with this part of SAE J2244 may be used at working pressures up to 40 MPa for nonadjustable stud ends and 31.5 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, applications, etc. For threaded ports and stud ends for use in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used in new designs in hydraulic fluid power applications. Conformance to the dimensional information in this SAE Standard does not guarantee rated performance.
Standard

Formed Tube Ends for Hose Connections

1986-05-01
HISTORICAL
J962_198605
This SAE Standard covers the dimensional and general specifications applicable to those formed tube end configurations suitable for hose connections made with or without hose clamps (see SAE J536) in relatively low pressure applications.
Standard

Formed Tube Ends for Hose Connections

1997-03-01
CURRENT
J962_199703
This SAE Standard covers the dimensional and general specifications applicable to those formed tube end configurations suitable for hose connections made with or without hose clamps (see SAE J536) in relatively low pressure applications.
Standard

Formed Tube Ends for Hose Connections

1976-06-01
HISTORICAL
J962B_197606
This SAE Standard covers the dimensional and general specifications applicable to those formed tube end configurations suitable for hose connections made with or without hose clamps (see SAE J536) in relatively low pressure applications.
Standard

Specification for O-Ring Materials Used with Hydraulic Connectors

2015-11-24
CURRENT
J515_201511
SAE J515 covers the specification for hydraulic O-ring material and properties and sizes applicable to face seal fittings, metric and inch stud ends, and four-bolt flange fittings. The standard includes a size code to allow industry and government agencies to order O-ring with a coded part number.
Standard

Specification for O-Ring Materials Used with Hydraulic Connectors

2010-01-07
HISTORICAL
J515_201001
SAE J515 covers the specification for hydraulic O-ring material and properties and sizes applicable to face seal fittings, metric and inch stud ends, and four-bolt flange fittings. The standard includes a size code to allow industry and government agencies to order O-ring with a coded part number.
Standard

Specification for O-ring Materials Used with Hydraulic Connectors

1990-11-01
HISTORICAL
J515_199011
SAE J515 covers the specification for hydraulic O-ring material and properties and sizes applicable to face seal fittings, metric and inch stud ends, and four-bolt flange fittings. The standard includes a size code to allow industry and government agencies to order O-ring with a coded part number.
Standard

Specification for O-ring Materials Used with Hydraulic Connectors

1990-06-01
HISTORICAL
J515_199006
SAE J515 covers the specification for hydraulic O-ring material and properties and sizes applicable to face seal fittings, metric and inch stud ends, and four-bolt flange fittings. The standard includes a size code to allow industry and government agencies to order O-ring with a coded part number.
Standard

Specification for O-ring Materials Used with Hydraulic Connectors

1989-06-01
HISTORICAL
J515_198906
SAE J515 covers the specification for hydraulic O-ring material and properties and sizes applicable to face seal fittings, metric and inch stud ends, and four-bolt flange fittings. The standard includes a size code to allow industry and government agencies to order O-ring with a coded part number.
Standard

Automotive Straight Thread Filler and Drain Plugs

2013-03-27
HISTORICAL
J532_201303
This SAE Standard includes complete general and dimensional specifications for those types of filler and drain plugs (shown in Figures 1 to 7 and Tables 1 to 3) having straight threads which are commonly used with gaskets or seals in automotive and related industrial applications.
Standard

Automotive Straight Thread Filler and Drain Plugs

1981-01-01
HISTORICAL
J532_198101
This standard includes complete general and dimensional specifications for those types of filler and drain plugs (shown in Figures 1 to 7 and Tables 1 to 3) having straight threads which are commonly used with gaskets or seals in automotive and related industrial applications.
Standard

Automotive Straight Thread Filter and Drain Plugs

2020-01-15
CURRENT
J532_202001
This SAE Standard includes complete general and dimensional specifications for those types of filler and drain plugs (shown in Figures 1 to 7 and Tables 1 to 3) having straight threads which are commonly used with gaskets or seals in automotive and related industrial applications.
Standard

Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading

1996-02-01
HISTORICAL
J356_199602
This SAE Standard covers normalized electric-resistance welded flash-controlled single-wall low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, flaring, beading, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead. This specification also covers SAE J356 Type -A tubing. The mechanical properties and performance requirements of standard SAE J356 and SAE J356 Type-A are the same. Therefore, the designated differences of Type-A tubing are not meant to imply that Type-A tubing is in anyway inferior to standard SAE J356. The Type-A designation is only meant to address the unique manufacturing differences of the small diameter, light wall sizes (typically 15.88 mm OD X 1.24 mm wall and smaller.)
X