Refine Your Search

Search Results

Standard

Fitting—O-Ring Face Seal

2009-01-13
CURRENT
J1453_200901
This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums.
Standard

Formed Tube Ends for Hose Connections

1986-05-01
HISTORICAL
J962_198605
This SAE Standard covers the dimensional and general specifications applicable to those formed tube end configurations suitable for hose connections made with or without hose clamps (see SAE J536) in relatively low pressure applications.
Standard

Formed Tube Ends for Hose Connections

1997-03-01
CURRENT
J962_199703
This SAE Standard covers the dimensional and general specifications applicable to those formed tube end configurations suitable for hose connections made with or without hose clamps (see SAE J536) in relatively low pressure applications.
Standard

Formed Tube Ends for Hose Connections

1976-06-01
HISTORICAL
J962B_197606
This SAE Standard covers the dimensional and general specifications applicable to those formed tube end configurations suitable for hose connections made with or without hose clamps (see SAE J536) in relatively low pressure applications.
Standard

Specification for O-Ring Materials Used with Hydraulic Connectors

2015-11-24
CURRENT
J515_201511
SAE J515 covers the specification for hydraulic O-ring material and properties and sizes applicable to face seal fittings, metric and inch stud ends, and four-bolt flange fittings. The standard includes a size code to allow industry and government agencies to order O-ring with a coded part number.
Standard

Specification for O-Ring Materials Used with Hydraulic Connectors

2010-01-07
HISTORICAL
J515_201001
SAE J515 covers the specification for hydraulic O-ring material and properties and sizes applicable to face seal fittings, metric and inch stud ends, and four-bolt flange fittings. The standard includes a size code to allow industry and government agencies to order O-ring with a coded part number.
Standard

Automotive Straight Thread Filler and Drain Plugs

2013-03-27
HISTORICAL
J532_201303
This SAE Standard includes complete general and dimensional specifications for those types of filler and drain plugs (shown in Figures 1 to 7 and Tables 1 to 3) having straight threads which are commonly used with gaskets or seals in automotive and related industrial applications.
Standard

Automotive Straight Thread Filter and Drain Plugs

2020-01-15
CURRENT
J532_202001
This SAE Standard includes complete general and dimensional specifications for those types of filler and drain plugs (shown in Figures 1 to 7 and Tables 1 to 3) having straight threads which are commonly used with gaskets or seals in automotive and related industrial applications.
Standard

Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading

1996-02-01
HISTORICAL
J356_199602
This SAE Standard covers normalized electric-resistance welded flash-controlled single-wall low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, flaring, beading, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead. This specification also covers SAE J356 Type -A tubing. The mechanical properties and performance requirements of standard SAE J356 and SAE J356 Type-A are the same. Therefore, the designated differences of Type-A tubing are not meant to imply that Type-A tubing is in anyway inferior to standard SAE J356. The Type-A designation is only meant to address the unique manufacturing differences of the small diameter, light wall sizes (typically 15.88 mm OD X 1.24 mm wall and smaller.)
Standard

Lubrication Fittings

2008-05-15
HISTORICAL
J534_200805
This SAE Standard covers complete general and dimensional specifications for the various types of lubrication fittings and related threaded components intended for general application in the automotive and allied fields.
Standard

Lubrication Fittings

2018-10-22
WIP
J534
This SAE Standard covers complete general and dimensional specifications for the various types of lubrication fittings and related threaded components intended for general application in the automotive and allied fields.
Standard

Coding Systems for Identification of Fluid Conductors and Connectors

2001-05-31
HISTORICAL
J846_200105
This coding system is intended to provide a convenient means of identifying the various tube, pipe, and hose fittings, not intended for use in aircraft, and of transmitting technical or engineering information relating to them wherever drawings or other pictorial media may not be readily available. The code has been kept flexible to permit expansion to cover new fitting categories or styles and, if the need develops, the inclusion of materials. The system is also compatible with automatic data processing equipment. It is not intended that this code should supersede established systems or means of identification. However, because the SAE code for automotive flare fittings shown in SAE J512 is also applicable to corresponding refrigeration fittings in SAE J513, both an SAE code and the existing code ANSI B70.1 are included throughout SAE J513. Therefore, it should be the prerogative of the user to apply that code which best satisfies his requirements.
Standard

Coding Systems for Identification of Fluid Conductors and Connectors

2004-01-05
HISTORICAL
J846_200401
This coding system is intended to provide a convenient means of identifying the various tube, pipe, hydraulic hose type and hose fittings, not intended for use in aircraft, and of transmitting technical or engineering information relating to them wherever drawings or other pictorial media may not be readily available. The code has been kept flexible to permit expansion to cover new fitting categories or styles and, if the need develops, the inclusion of materials. The system is also compatible with automatic data processing equipment. It is not intended that this code should supersede established systems or means of identification. However, because the SAE code for automotive flare fittings shown in SAE J512 is also applicable to corresponding refrigeration fittings in SAE J513, both an SAE code and the existing code ANSI B70.1 are included throughout SAE J513. Therefore, it should be the prerogative of the user to apply that code which best satisfies his requirements.
Standard

Coding Systems for Identification of Fluid Conductors and Connectors

2007-12-13
HISTORICAL
J846_200712
This coding system is intended to provide a convenient means of identifying the various tube, pipe, hydraulic hose type and hose fittings, not intended for use in aircraft, and of transmitting technical or engineering information relating to them wherever drawings or other pictorial media may not be readily available. The code has been kept flexible to permit expansion to cover new fitting categories or styles and, if the need develops, the inclusion of materials. The system is also compatible with automatic data processing equipment. It is not intended that this code should supersede established systems or means of identification. However, because the SAE code for automotive flare fittings shown in SAE J512 is also applicable to corresponding refrigeration fittings in SAE J513, both an SAE code and the existing code ANSI B70.1 are included throughout SAE J513. Therefore, it should be the prerogative of the user to apply that code which best satisfies his requirements.
X