Search Results

Mass-related properties of four atomizers were estimated with the use of a mechanical transient patternator. The properties presented on a temporal and spatial basis are the axial liquid mass flux, liquid fuel to air ratio, and liquid axial velocity. The data are presented in two formats. The first format consists of the mass-related properties that occurred radially between two planes positioned 2.0 cm and 2.25 cm along the atomizer axis. A second format consists of interpolated contour plots of the axial liquid mass flux for all of the spray systems studied. The atomizers used in the study consisted of three liquid-only high-pressure systems and one air-assist system. Two of the liquid-only high-pressure systems and the air - assist system were operated with a volumetric delivery of 20 mm3 per injection while injecting into ambient conditions. A third liquid-only high-pressure system was operated with a delivery of 15 mm3 per injection.

Simultaneous droplet sizes and velocities were obtained for a transient diesel fuel spray in a quiescent chamber at atmospheric temperature and pressure. Instantaneous injection pressure, needle lift, and rate of injection were also measured, allowing calculation of the instantaneous nozzle discharge coefficient. Short-exposure still photographs were obtained at various chamber pressure and densities to further investigate this spray. Correlations between droplet size and velocity were determined at each crank angle to observe the detailed nature of the transient events occurring in this transient diesel fuel spray. As expected, peak mean and rms velocities are observed in the center of the spray. Measured average velocities are consistent with a calculated value, using the discharge coefficient for the nozzle and the known rate of fuel injection.

Pilot injection and two other forms of auxiliary fuel introduction have been studied for their effects on diesel engine combustion and emissions. A two-stroke diesel has been equipped with an electronic solenoid-controlled unit injector such that the injector can operate with pilot injection. In addition, the engine has been fitted with experimental air-blast atomizing injectors in the inlet port and intake manifold. In-cylinder pressure, Bosch smoke, exhaust hydrocarbons, NO and NOx emissions measurements have been made for a range of engine conditions. In addition, two fuels have been tested to observe the effects of fuel blend on the auxiliary fuel behavior. In general, the effect of auxiliary fuel introduction is to reduce ignition delay and rate-of-pressure rise. This tends to result in a decrease in NO emissions. Unburned hydrocarbons and smoke tend to increase, although not in every case.

The objective of this study was to observe and attempt to understand the effects of equivalence ratio and simulated exhaust gas recirculation (EGR) on the exhaust emissions and performance of a L-head single cylinder utility engine. In order to isolate these effects and limit the confounding influences caused by poor fuel mixture preparation and/or vaporization produced by the carburetor/intake port combination, the engine was operated on a premixed propane/air mixture. To simulate the effects of EGR, a homogeneous mixture of propane, air, and nitrogen was used. Engine measurements were obtained at the operating conditions specified by the California Air Resources Board (CARB) Raw Gas Method Test Procedure. Measurements included exhaust emissions levels of HC, CO, and NOx, and engine pressure data.

A laboratory-based fuel mixture preparation system has been developed that is capable of generating a wide range of fuel/air mixtures, including production of a premixed, prevaporized homogeneous charge, beginning with liquid gasoline fuel. This system has been developed to allow the study of the effects of fuel/air mixture preparation characteristics on engine combustion, in-cylinder pressure, and exhaust emissions. For the study to be described here, engine combustion behavior and emissions measurements were obtained for a wide range of A/F's with the fuel mixture preparation being produced in one case, by the stock carburetor operating with fixed throttle position, and the other case, with the custom-built system producing a homogeneous mixture (HM.) A four-stroke, spark-ignited, single-cylinder, overhead valve-type utility engine was used for all tests.

Control of the flow of thermal energy in an air-cooled engine is important to the overall performance of the engine because of potential effects on engine performance, durability, design, and emissions. A methodology is being developed for the assessment of thermal flows in air-cooled engines, which includes the use of cycle simulation and in-cylinder heat flux measurements. The mechanism for the combination of cycle simulation, the measurement of in-cylinder heat flux and wall temperatures, and comparison of predicted and measured heat flux in the methodology is presented. The methodology consists of both simulation and experimental phases. To begin, a one-dimensional gas dynamics code (WAVE) has been used in conjunction with a detailed in-cylinder flow and combustion model (IRIS) in order to simulate engine operation in a variety of operating conditions. The methods used to apply the model to the air-cooled engine case are described in detail.

A laboratory-based fuel mixture system capable of delivering a range of fuel/air mixtures has been used to observe the effects of differing mixture characteristics on engine combustion through measurement and analysis of incylinder pressure and exhaust emissions. Fuel air mixtures studied can be classified into four different types: 1) Completely homogeneous fuel/air mixtures, where the fuel has been vaporized and mixed with the air prior to entrance into the normal engine induction system, 2) liquid fuel that is atomized and introduced with the air to the normal engine induction system, 3) liquid fuel that is atomized, and partially prevaporized but the air/fuel charge remains stratified up to introduction to the induction system, and 4) the standard fuel metering system. All tests reported here were conducted under wide open throttle conditions. A four-stroke, spark-ignited, single-cylinder, overhead valve-type engine was used for all tests.

Two distinct atomization strategies are contrasted through the measurement of time and spatially dependent mass flux. The two systems investigated include a pressure atomizer (6.9 MPa opening pressure) and an air-assist atomizer. Both systems have potential for use in direct injection spark ignition engines. The mass flux data presented were obtained using a spray patternator that was developed to allow phased sampling of the spray. The temporal mass related history of the spray was reconstructed as volume versus time plots and interpolated mass flux contour plots. Results indicate substantial differences in the distribution of both mass and mass flux in space and time for the two injection systems. For example, the pressure atomizer at high mass delivery rates produced a spray that collapsed into a dispersed cylindrical shape while at low rates, generated a hollow cone structure.

This paper reports on the investigation of injection pressure upon the droplet behavior in transient diesel sprays. Phase/Doppler results for a Diesel spray with a maximum fuel injection line pressure of 105 MPa are compared with previously acquired droplet size and velocity measurements for a Diesel spray with an injection pressure of 21 MPa. All measurements reported here were made in atmospheric conditions at a position near the nozzle. It is shown in these results that the droplet velocity and size profiles do maintain similarity despite the substantial change in injection pressure. Specific characteristics, for example, the appearance of subtle waves in the time-dependent spray data, are present in both data sets. Comparison of the measured droplet velocities and diameters with Weber number based stability criteria shows that increased injection pressure produces a higher percentage of droplets that are likely to breakup.

Cyclic variation is examined by: (1) conditional grouping and heat-release analysis to reveal different modes of combustion, (2) considering the order in which the burn modes occur to establish prior-cycle effects and (3) comparing the measured variation in IMEP with data generated by simple models. Results show that several burn modes may exist, particularly under fuel-lean conditions. Prior-cycle effects also become more obvious as the air-fuel ratio is increased. Finally, comparisons with data generated by simple models show that the nature of cyclic variation may range from completely stochastic to a superposition of a non-chaotic deterministic process on a stochastic process.

An in-cylinder optical sensor has been developed and tested for use in spark-ignition engine combustion analysis and control, This sensor measures the luminous emission in the near infrared region. Results of these tests show good correlation between the measured luminosity and traditional combustion parameters, such as location and magnitude of maximum cylinder pressure, and location and magnitude of maximum heat release. Engine performance indicators, such as the indicated mean effective pressure (IMEP), also can be determined accurately with the measured luminosity combined with other engine operating parameters, e.g. intake manifold pressure. In-cylinder air-fuel ratio can be determined with accuracy over an ensemble of 100 cycles.

Conditional sampling of cylinder-pressure data is used to investigate cyclic variability in a premixed-charge spark-ignited engine operating under fuel-lean conditions. Unlike straight ensemble averaging of pressure data, conditional sampling applies a set of constraints to the pressure data such that like combustion events can be identified and grouped together. Ensemble averaging of pressure data from an engine that exhibits significant cycle-to-cycle variation is shown to produce a mean pressure history that is not representative of the combustion process. Conditional sampling provides a means of identifying and analyzing the different groups of pressure histories and therefore the different types of combustion processes that occur in an engine that exhibits cyclic variability.

Measurements of the instantaneous heat flux at three positions on the cylinder head surface, and the steady-state cylinder head temperatures at four positions on the cylinder head have been obtained. Engine tests were performed for a range of air-fuel ratios including regimes rich of stoichiometric, stoichiometric, and lean of stoichiometric. In addition, ignition timing was advanced in increments from 22° BTDC to 40° BTDC. All tests were run with the throttle either fixed in the wide open position, or fixed in a position that produced 75% of the maximum power with the standard ignition timing and an air-fuel ratio of 13.5. This was done to ensure that changes in air mass flow rate were not influencing the results. In addition, all tests were performed with a fuel mixture preparation being provided by system designed to deliver a homogeneous premixed charge to the inlet port. This was done to ensure that mixture preparation issues were not confounding the results.