Search Results

The reliability of electronic components is of increasing importance for further progress towards automated driving. Thermal aging processes such as electromigration is one factor that can negatively affect the reliability of electronics. The resulting failures depend on the thermal load of the components within the vehicle lifetime - called temperature collective - which is described by the temperature frequency distribution of the components. At present, endurance testing data are used to examine the temperature collective for electronic components in the late development stage. The use of numerical simulation tools within Vehicle Thermal Management (VTM) enables lifetime thermal prediction in the early development stage, but also represents challenges for the current VTM processes [1, 2]. Due to the changing focus from the underhood to numerous electronic compartments in vehicles, the number of simulation models has steadily increased.

In this article the unsteady aerodynamic properties of a 25% scale DrivAer notchback model as well as the influence of the wind tunnel environment on the resulting unsteady aerodynamic forces and moments under crosswind excitation are investigated using experimental and corresponding numerical methods. Research Institute of Automotive Engineering and Vehicle Engines Stuttgart (FKFS) swing® (side wind generator) is used to reproduce the essential properties of natural stochastic crosswind in the open jet test section of the Institute for Internal Combustion Engines and Automotive Engineering (IVK) model scale wind tunnel (MWK). The results show that the test environment of an open jet wind tunnel alters the amplitudes of side force and yaw moment under crosswind excitation when compared to an ideal environment neglecting wind tunnel interference effects.

In this paper the influence of different turbulent flow conditions on the aerodynamic drag of a quarter scale model with notchback and estate back rear ends is investigated. FKFS swing® (Side Wind Generator) is used to generate a turbulent flow field in the test section of the IVK model scale wind tunnel. In order to investigate the increase in drag with increasing yaw, a steady state yaw sweep is performed for both vehicle models. The shape of the drag curves vary for each vehicle model. The notchback model shows a more pronounced drag minimum at 0° yaw angle and experiences a more severe increase in drag at increasing yaw when compared to the estate back model. Unsteady time averaged aerodynamic drag values are obtained at two flow situations with different turbulent length scales, turbulence intensities, and yaw angle amplitudes. While the first one is representing light wind, the second one is recreating the presence of strong gusty wind.

The entire automotive industry is moving towards lower CO₂ emissions and higher energy efficiency. Especially for higher driving speeds this can be achieved by minimizing aerodynamic drag. Additionally, aerodynamic downforce is essential to maintain or even improve the handling performance of a vehicle. In order to optimize the vehicle's aerodynamic efficiency in wind tunnel tests, the boundary conditions of a vehicle driving on a road must be simulated properly. Particularly for optimizing the underbody region of a vehicle, ground simulation is an important issue in every wind tunnel. Today rolling road systems featuring one or more moving belts on the wind tunnel floor are a standard tool to simulate the complex boundary condition of a vehicle driving on the road. But generally the technical effort to measure aerodynamic forces accurately increases with improvement of the aerodynamic ground simulation.

For many years FKFS has operated the full-scale aeroacoustic wind tunnel of University of Stuttgart. To keep this wind tunnel as one of the most modern ones of its kind, it has again been upgraded significantly. The upgrade improved the aerodynamic as well as the aeroacoustic performance and accelerated the operational processes. Additionally, new innovative features have significantly enlarged the test capabilities. A new patented, modular belt system (FKFS first®) allows high performance measurements for race cars in a 3-belt mode as well as efficient measurements for production vehicle development in a 5-belt mode. The belt system is accompanied by a new, larger turntable and a new under-floor balance which enables high-accuracy measurements of forces and moments also for a high resolution in time. For the elimination of parasitic forces generated at the wheel drive units, a specific correction procedure has been implemented, which is patented, too (FKFS pace®).

In this paper the effect of aerodynamic modifications that influence the unsteady aerodynamic properties of a vehicle on the response of the closed loop system driver-vehicle under side wind conditions is investigated. In today's aerodynamic optimization the side wind sensitivity of a vehicle is determined from steady state values measured in the wind tunnel. There, the vehicle is rotated with respect to the wind tunnel flow to create an angle of attack. In this approach however, the gustiness that is inherent in natural wind is not reproduced. Further, unsteady forces and moments acting on the vehicle are not measured due to the limited dynamic response of the commonly used wind tunnel balances. Therefore, a new method is introduced, overcoming the shortcomings of the current steady state approach. The method consists of the reproduction of the properties of natural stochastic crosswind that are essential for the determination of the side wind sensitivity of a vehicle.

Within in the scope of a road load investigation project at FKFS, the influence of rotating wheels on the road load of a passenger car was investigated. For this purpose an approach was developed to measure the ventilation resistance of a spinning wheel. This approach enables a comparison of different wheel sizes and rim designs. Together with aerodynamic drag measurements in the wind tunnel it is possible to evaluate different wheel configurations with respect to their contribution to the road load. The measuring approach and results of performed measurements are shown in this paper.

This paper presents some recent results concerning the generation and minimization of cooling air drag, achieved in an integrated approach of numerical and experimental investigations. The baseline configuration of a production cars' cooling air flow system is analyzed. The analysis of the created drag shows, that most of the force changes due to the cooling air flow appear in the front region of the vehicle. However, the forces generated by heat exchangers are only a small share of the total changes. Additional drag is generated for example by the front wheels and by the components of the underhood compartment. The investigation of the influence of the vehicle rear end shape on the aerodynamics of the cooling air flow system shows, that two similar cars with different rear end shapes (notchback and squareback) can feature different cooling air drag values.

Previous work by the authors showed the development of an aerodynamic CFD model using the Lattice Boltzmann Method for simulating vehicles inside the IVK Model-Scale Wind-Tunnel test-section. In both experiment and simulation, alternate configurations of the wind-tunnel geometry were studied to change the pressure distribution in the wind-tunnel test section, inducing a reduction in aerodynamic drag due to interference between the wind-tunnel geometry and the pressure on the surface of the vehicle. The wind-tunnel pressure distribution was modified by adding so-called “stagnation bodies” inside the collector to create blockage and to increase the pressure in the rear portion of the test section. The primary purpose of previous work was to provide a validated CFD approach for modeling wind-tunnel interference effects, so that these effects can be understood and accounted for when designing vehicles.

This paper presents velocity and pressure measurements obtained around an isolated wheel in a rotating and stationary configuration. The flow field was investigated using LDA and a total pressure probe in the model scale wind tunnel at IVK/FKFS. Drag and lift were determined for both configurations as well as for the wheel support only. These results were used as a reference for comparing numerical results obtained from two different CFD codes used in the automotive industry, namely STAR-CD™ and PowerFLOW™. The comparison gives a good overall agreement between the experimental and the simulated data. Both CFD codes show good correlation of the integral forces. The influence of the wheel rotation on drag and lift coefficients is predicted well. All mean flow structures which can be found in the planes measured with LDA can be recognized in the numerical results of both codes. Only small local differences remain, which can be attributed to the different CFD codes.

In automotive wind tunnels with modern road simulation installations boundary layer pre-suction is a widely-used technique for boundary layer control. The consequence of boundary layer pre-suction is an additional pressure gradient in front of the model. In order to investigate the effects of the additional pressure gradient on drag, experiments were conducted with two different models (scale 1:5) in the IVK Model Wind Tunnel. In these experiments the suction velocity of the boundary layer pre-suction served as a parameter to change the static pressure gradient along the test section and was for this purpose adjusted higher and lower than the standard suction velocity. It is shown that the total drag increment due to boundary layer pre-suction consists of at least two parts: the ground simulation increment and the static pressure gradient increment. The ground simulation increment is due to a decrease in the boundary layer thickness and the resulting modified flow beneath the model.

The number of electronic control units (ECU) in modern automobiles has steadily increased lately. Joining them in a vehicle network causes complex bus structures, in which ECU's of different suppliers have to cooperate. In order to keep the development effort as small as possible, the automobile industry would rather have the possibility of testing these bus structures in an early state of development. This was the reason why we created a test system for the network management of a CAN-Low-Speed network, which supports the test of an electronic control system in many states of development. This test system is able to check different network structures and to search errors in the ECU's by checking the network management. This is done by an automatic test that generates an evaluation and a report.

Investigating the crosswind behavior of passenger cars is one main research subject at the Research Institute of Automotive Engineering and Vehicle Engines Stuttgart (FKFS), an institute of the University of Stuttgart. Faced with the vehicle dynamics during stochastic crosswind, this paper is concerned with the evaluation of the crosswind behavior as experienced by the driver. Most of the evaluation criteria of crosswind are currently based on the vehicle reactions only and exclude the driver's actions. A comparison of the crosswind behavior of two vehicles at the FKFS showed a non-uniform - in some cases even contrary - evaluation when applying these criteria. This paper introduces a new approach to considering the vehicle's crosswind behavior which includes the driver's reactions. The fundamental issue of this new approach is to derive the driver's evaluation from their steering inputs when compensating for the crosswind excitation. In other words: The driver is used as a sensor.

Within the scope of a current research project at the Research Institute of Automotive Engineering and Vehicle Engines Stuttgart (FKFS), the potential for an estimation of vehicle side slip angle and yaw rate arising from online measurement of tire forces is evaluated. Investigations focus on how the vehicle state can be determined, if in addition to wheel speeds and steering angle the tire forces currently acting on the vehicle are known. Different estimation procedures based on inverse tire models, direct integration of vehicle accelerations and closed-loop-observer are discussed. The performance is tested with data from vehicle dynamics simulation.

This paper introduces a driving-torque measurement method for the determination of vehicle road load and its components. To increase the accuracy, the torque measurements are combined with rolling resistance measurements performed with a specially developed trailer. This method is a strictly experimental approach and does not use any mathematical models. The experimental techniques are described as well as the proceedings to compare test stand and road measurements. The results that are shown prove that this method is suitable for the investigation of single road load components. Furthermore, the comparison of different rolling resistance measurement devices shows the potential of the measurement trailer and the necessity to perform rolling resistance measurements on real road surfaces and not solely on test stands.

In 2001 the FKFS (Research Institute of Automotive Engineering and Vehicle Engines, Stuttgart) took into operation state-of-the-art 5-belt systems for road simulation in the 22.45m2-IVK automotive wind tunnel and in the 1.65m2-IVK model wind tunnel. In these systems, a narrow belt running between the vehicles' wheels is fitted with 4 balance-mounted wheel rotation drives and a vehicle restraint system. The FKFS opted for MTS steel belt technology due to its small size, low power requirements and excellent tracking stability. Due to air bearings below the belt, the flat-belt wheel rotation units in the full-scale wind tunnel permit aerodynamic force measurements at full wheel load (8 kN) up to 70 m/s. In combination with the hydrostatic suspension of the units, integrated longitudinal force transducers permit realistic measurements of the wheels' rolling resistance. In the model wind tunnel FKFS wheel rotation units with Poly-V belts are used with small wheel loads up to 80 m/s.

With its recent wind tunnel upgrade, FKFS installed the first interchangeable three-belt / five-belt-system (FKFS first®) in a full scale automotive wind tunnel. With the five-belt system, which today is a state-of-the-art ground simulation technique, the system is ideally suited for production vehicle development work. The five-belt system offers high flexibility, quick access to the underfloor and vehicle fixation, and setting the vehicle’s ride height by the restraint device. The first results of the five-belt system have already been published in SAE 2015-01-1557 [1]. The three-belt system on the other hand, offers a much more sophisticated ground simulation technique which is necessary especially for sports and racing cars. For such vehicles with very low ground clearances, it is important to have a more accurate ground simulation, in order to capture the same aerodynamic modes of action and response as on the road.

In the digital prototype development process of a new Mercedes-Benz, thermal protection is an important task that has to be fulfilled. In the early stages of development, numerical methods are used to detect thermal hotspots in order to protect temperature sensitive parts. These methods involve transient full Vehicle Thermal Management (VTM) simulations to predict dynamic vehicle heat-up during critical load cases. In order to simulate thermal control mechanisms, a coupled 1D to 3D thermal vehicle model is built in which the coolant and oil circuit of the engine, as well as the exhaust flow are captured in detail. When performing a transient 3D VTM analysis, the conduction and radiation phenomena are simulated using a transient structure model while the convective phenomena are co-simulated in a steady state fluid model. Both models are brought to interaction at predetermined points by an automatized coupling method.

The present paper reveals the design concept as well as results of experimental investigations, which were conducted in the early design stage of the planned AUDI Aero-Acoustic Wind Tunnel. This low-noise open-jet facility, featuring a nozzle exit area of 11 m2 and a top speed of approximately 60 m/s, enables aerodynamic as well as acoustic testing of both, full-scale and model-scale ground vehicles. Ground simulation is provided by means of a moving-belt rig. The surrounding plenum is designed as a semi-anechoic chamber to simulate acoustic free-field conditions around the vehicle. Fan noise will be attenuated below the noise level of the open jet. The work reported herein, comprises 1/8-scale pilot-tunnel experiments of aerodynamic and acoustic configurations which were carried out at the University of Darmstadt.

In automobile development, wind tunnel measurements are used to optimize fuel consumption and the vehicle's road behavior. The classic measuring technique is based on a stationary vehicle set up in the wind tunnel with stationary wheels. Relative movement between vehicle and road surface is therefore ignored. In more recent studies, measurements have been taken with improved ground simulation. For example, a belt is used instead of the stationary wind tunnel floor and the car wheels rotate. Ground simulation using a belt and rotating wheels generally leads to a reduction in flow angularity at the front wheels, in the same way as blocking the cooling air flow, whereby, as a matter of fact, the aerodynamic drag is reduced. Analogous air flow angle correlations can be established for the effect of underfloor panels.