Search Results

On the basis of the large amount of know-how accumulated in the field of automotive ethanol SI-engine fuelling in Brazil, it seemed appropriate to continue and set a new milestone in the usage of ethanol fuel. The paper presents the preliminary study made to enable the transfer of the ethanol technology to a 5.9-liter 4-cylinder boxer aircraft engine. The study describes the steps made to define the optimal parameter configuration for the transfer of the fuel system packaging, the fuel injector layout, the engine control unit (ECU) and the legislative redundancy requirements for aviation applications. The paper illustrates the use of numerical simulation techniques and special visualization approaches necessary to understand the physical phenomena of mixture preparation (spray atomization and momentum). Two different layouts are presented and discussed and a certain number of experimental results obtained with the retained solution are presented and discussed.

The suggestions for upcoming Euro 2000 clean air act puts an increasing legislative pressure for lower specific fuel consumption in order to reduce the emission of CO2 and thereby decrease the impact of the “green house” effect. One of the possible suggestions to meet these requirements for SI-engines is the gasoline direct injected (GDI) power unit. One of the key points of the success of a layout of a GDI system is the optimization of the fuel injector and combustion chamber charge formation parameters. A brief description of the basic GDI-system used during the study is given. Hereafter are outlined the computational and experimental optimization tools which have been used to produce, on a reasonable industrial time scale, the main indications to optimize the design of a given injector/chamber configuration. The paper discusses in detail the results produced by the latest enhancements introduced into the 3D multi-phase computational approach, NCF-3D.

The success obtained by use of Virtual Engine Modeling (VEM) in the design and development areas of fuel injectors generated a lot of interest from production and quality engineers to dispose of a similar tool related to spray vessel measurements. To respond to stringent PL6/EURO5 requirements it was decided to develop a Virtual Spray Vessel (VSV) tool capable of predicting spray patters and perform droplet diameter analysis comparable to Phase Doppler Analysis (PDA) results. The paper describes the analogies between VEM and VSV modeling, the specific new numerical approaches to obtain spatial spray data comparable to conventional mechanical measurement techniques and to perform droplet diameter analysis comparable to PDA data. The paper concludes with a series of comparisons of simulated and experimental data.

The first part of the paper gives an overview of the current results obtained with the first-generation of GDI-powered vehicles launched on the European market. In view of the rather limited success in fuel consumption gain the second-generation of very lean stratified layouts has begun, but this process requires the development and application of new high-level analysis tools. A possible high performance approach is the multi-purpose use of 3-D numerical simulation both in the development and the engine control strategy calibration phases. The development of a small 1.6 liter lean stratified engine project was chosen to demonstrate the dual application capability of the NCF-3D simulation tool. The paper continues with a description of the engine application frame, the basic features of the NCF-3D simulation tool and the latest enhancements made to combustion and fuel composition models within the software frame.

The new European legislation on two-wheeler pollutant emissions has forced two stroke engine manufacturers to study the direct fuel injection (DI) technology. The Piaggio “ET2 Injection” was the first DI engine in production, using the FAST system (Fully Atomized Stratified Turbulence) applied on a 50 cm3 engine. Within the framework of the DOLCE project (Development Of innovative Low pollutant, noise and fuel Consumption two stroke spark ignition Engines for future vehicles for individual urban mobility) coordinated by Piaggio and supported by the European Commission, a 125 cm3 direct injection 2-stroke engine was developed. This paper presents the engine-related part of this work, which was concluded in March 2000. The engine is equipped with the FAST system and the fuel metering is performed by means of a low-pressure electronic fuel injection system integrated in an Engine Management System (EMS) specially developed for this type of application.

In the present paper are examined the consequences of a substantial rise in the injection pressure for Gasoline Direct Injection (GDI) injector assemblies. The paper presents a comparative study of the spray behavior of two different injector nozzle layouts submitted to current 10 Mpa rail-pressure as well as to a 30 Mpa injection pressure. To evaluate the differences in the fundamental physical spray parameters are used several specially developed optical visualization techniques, which enable phase-Doppler, PIV, Laser-sheet and high-speed recordings of dense high pressure fuel sprays. A recently developed injector actuator and the necessary modifications to existing high-pressure pumps to reach a 30 MPa pressure level in the fuel system are presented. The change in basic spray parameters (time-resolved droplet distribution and spray momentum) caused by the rail-pressure rise is examined.

The paper presents the background research on the physics of the droplet coalescence phenomena carried out by an interactive usage of high-level 3-D numerical simulation tools and high-level optical visualization and measurement techniques. The presentation continues with the description of a new injector atomizer plate layout, which enables a physical coalescence control of the droplet population within the entire fuel spray. Finally are presented examples of the impact on exhaust emissions of the introduction the new atomizer plate with coalescence control by engine test bed experiments (steady state low load conditions) and vehicle tests (first cold part of the FTP-cycle).

In the future generation of low consumption SI-engine layouts, it has become necessary to reduce costs as well as the complexity level and, increase the system reliability by the latter. To avoid driving the GDI-system in the critical, very lean stratified operation mode without losing the fuel consumption benefit, a solution is suggested, which combines a fully variable valve control system with a low level, robust GDI combustion layout. The first part of the present paper presents the latest development in the field of high precision multi-hole GDI injector spray nozzles. The basic aspects of mixture preparation with multi-hole gasoline atomizers are highlighted and their spray behavior compared to that of the current swirl atomizer nozzle. The second part of the paper presents primary optimization of a largely homogeneous GDI combustion layout combined with a fully variable valve timing control system including complete cylinder de-activation.

The first part of the paper outlines the main potential advantages of the direct fuel injection concept and describes the overall layout of a system in which the keystones are a piston rotary fuel delivery pump with integrated pressure regulation and electromechanical fast responding fuel injectors. Three different nozzle designs are discussed, a divergent pintle solid cone, a pintle hollow cone swirl layout and a closed cap multijet design. In the second part of the paper the used experimental high pressure dynamic test equipment is discussed. Then the results obtained by the use of phase illuminated visualisation techniques and phase Doppler analysis as well as by a 3D CFD approach are presented. The paper concludes by relating the spray patterns and the associated droplet penetration velocities, produced by the different nozzle types, to the combustion chamber layout and to the possible manufacturing precision requirements for each nozzle type.

The present paper is a contribution in which is used a numerical simulation approach, the Virtual Engine Model, to study the combination of the Compression Ignition process with a Gasoline Direct Injection mixture preparation in a limited number of load-points. The first part of the paper describes the reasons for which current Gasoline Direct Injection engine technology must be combined with other technologies related to the in-cylinder mixture preparation control to further increase their potential for decreased fuel consumption. The paper continues with a description of the physics of spark and compression ignited processes as well as of the involved mixture preparation hardware components. The setup and the practical use of the Virtual Engine Model are discussed for both spark and compression ignited approaches.

The paper presents the today’s power train systems, which largely reflect a one to one mapping of physical units into a dedicated electronic control system. A new approach is suggested for a breakdown strategy with an ECU centered structure linked to a surrounding harness of sensors and actuators. Like body electronics did first, automotive graded combination of semiconductor and packaging technologies are used to develop a network of mechatronic components. This allows an easy and effective separation between the SW development at the vehicle level and an off-line optimization and calibration of components. A development project is shown for a gasoline direct injected engine, where mechatronic components (e.g. cylinder, fuel pump and injectors, valve train) are networked and controlled by a master digital core, which is the application SW restricted area of the car manufacturer.

The paper describes the setup of a 4-cylinder 1.4-liter prototype Spark Ignited (SI)-engine, which is highly boosted, extremely downsized and port fuel injected. During experimental data gathering with the engine it was discovered that the originally mounted fuel injectors were non-optimized an unable to produce an expected low fuel consumption performance at low speed, low load engine working conditions. To solve this problem by finding an optimized alternative solution for the mixture preparation process it was decided to use a high-performance numerical simulation tool. The paper presents the overall layout of the prototype engine as well as the structure of the 3-D dynamic optimization tool used to address the mixture preparation problem. The paper continues with a detailed description of the different steps used to reach the complete optimization of the mixture preparation system (both the fuel injectors and the intake manifold).

The first part of the paper gives an overview of the current status in fuel consumption gain of the GDI-vehicles previously launched on the European market. In order to increase the potential for a further gain in specific fuel consumption the behaviour of 3 different combustion chamber layouts are studied. The chamber layouts are aimed to adapt as well as possible to the particular requirements for application to a small displacement/small bore engine working in stratified lean conditions. The paper continues with a description of the application that shows the different steps of a structured optimisation methodology for a 1.2 litre, small bore 4-cylinder engine. The applications of an air-motion-guided and a wall-guided layout with a mechanically actuated valve train to the same combustion chamber are discussed. The potential of the air-motion-guided concept is enhanced through the introduction of an electromagnetic fully variable valve train.