Search Results

Downsizing is widely considered one of the main path to reduce the fuel consumption of spark ignition internal combustion engines. As known, despite the reduced size, the required torque and power targets can be attained thanks to an adequate boost level provided by a turbocharger. However, some drawbacks usually arise when the engine operates at full load and low speeds. In fact, in the above conditions, the boost pressure and the engine performance is limited since the compressor experiences close-to-surge operation. This occurrence is even greater in case of extremely downsized engines with a reduced number of cylinders and a small intake circuit volume, where the compressor works under strongly unsteady flow conditions and its instantaneous operating point most likely overcomes the steady surge margin. In the paper, both experimental and numerical approaches are followed to describe the unsteady behavior of a small in-series turbocharger compressor.

Turbocharging technique will play a fundamental role in the near future not only to improve automotive engine performance, but also to reduce fuel consumption and exhaust emissions both in Spark Ignition and diesel automotive applications. To achieve excellent engine performance for road application, it is necessary to overcome some typical turbocharging drawbacks i.e., low end torque level and transient response. Experimental studies, developed on dedicated test facilities, can supply a lot of information to optimize the engine-turbocharger matching, especially if tests can be extended to the typical engine operating conditions (unsteady flow). Different numerical procedures have been developed at the University of Naples to predict automotive turbocharger compressor performance both under steady and unsteady flow conditions. A classical 1D approach, based on the employment of compressor characteristic maps, was firstly followed.

Turbocharging is becoming a key technology for automotive spark ignition engines (fed with both liquid and gaseous fuel) as a support to the downsizing concept in order to reduce fuel consumption and exhaust emissions. A waste-gate valve is usually fitted as turbocharger control system in these applications, due to its ability to work at very high exhaust gas temperatures. However, not much information is generally available on turbine behaviour in the opened waste-gate area. This paper presents the results of an experimental study developed on a waste-gated turbocharger for downsized SI automotive engines, performed on the test rig operating at the University of Genoa (Italy), extended both to steady and unsteady flow operation. Mass flow through the by-pass valve and turbine impeller was measured at different waste-gate settings in steady flow conditions.

Turbocharging is playing today a fundamental role not only to improve automotive engine performance, but also to reduce fuel consumption and exhaust emissions for both Spark Ignition and diesel engines. Dedicated experimental investigations on turbochargers are therefore necessary in order to get a better understanding of its performance. The availability of experimental information on realistic turbine steady flow performance is an essential requirement to optimize engine-turbocharger matching calculations developed in simulation models. This aspect is more noticeable as regards turbine efficiency, since its swallowing capacity can be accurately evaluated through the measurement of mass flow rate, inlet temperature and pressure ratio across the machine. Actually, in the case of a turbocharger turbine, isentropic efficiency directly evaluated starting from measurement of thermodynamic parameters at the inlet and outlet sections can give significant errors.

Today turbocharging represents a key technology to reduce fuel consumption and exhaust emissions for both Spark Ignition and diesel engines, moreover improving performance. 1D models, generally employed to compute the engine-turbocharger matching conditions, can be optimized basing on certain information about turbine and compressor behavior. Because of difficulty in the correct evaluation of turbine isentropic efficiency with direct techniques, turbocharger turbine efficiency is generally referred to thermomechanical efficiency. To this aim, the possibility to accurately estimate power losses in turbocharger bearings can allow the assessment of the turbine isentropic efficiency starting from the thermomechanical one. In the paper, an experimental and theoretical study on turbocharger mechanical losses is presented. The proposed model, developed in the MATLAB environment, refers to radial and axial bearings.

A wide investigation on powered two-wheelers (PTWs) is presented, aiming at the analysis of the influence of the driving characteristics on PTWs exhaust emissions and fuel consumption, a deeper comprehension of the engine and after-treatment system behavior within the cold start transient and the evaluation of cold start additional emissions for different two-wheelers classes. The study was developed with reference to an European context focusing on Euro 3 motorcycles and Euro 2 mopeds. An experimental investigation on instantaneous speed measurements was carried out with instrumented motorcycles, considering typical urban trips in the city of Genoa. A selection of speed profiles was then performed by processing experimental values.

The paper presents the main results of a study focused on the definition of exhaust emission factors for a waste collection vehicles fleet, taking into account the specific mission profiles. As a first step, on the basis of the fleet characteristics, different classification criteria were applied, aiming at the identification of suitable vehicle classes. Then, the calculation of the exhaust emissions for each class was based on a two terms equation, the first related to the vehicle travel (considering different sources for the relevant emission factors) and the second to the equipment use, whose contribution is estimated on the basis of different parameters. A computational code was then set up for the evaluation of the daily emission of normalized pollutants for the whole fleet and each required service.

Turbocharging is playing today a fundamental role not only to improve automotive engine performance, but also to reduce fuel consumption and exhaust emissions for both Spark Ignition and Diesel engines. Dedicated experimental investigations on turbochargers are therefore necessary to assess a better understanding of its performance. The availability of experimental information on turbocharger steady flow performance is an essential requirement to optimize the engine-turbocharger matching, which is usually achieved by means of simulation models. This aspect is even more important when referred to the turbine efficiency, since its swallowing capacity can be accurately evaluated through the measurement of mass flow rate, inlet temperature and pressure ratio across the machine.

Downsizing and boosting is currently the principal solution to reduce fuel consumption in automotive engines without penalizing the power output. A key challenge for controlling the boost pressure during highly transient operations lies in avoiding to operate the turbocharger compressor in its instability region, also known as surge. While this phenomenon is well known by control engineers, it is still difficult to accurately predict during transient operations. For this reason, the scientific community has directed considerable efforts to understand the phenomena leading to the onset of unstable behavior, principally through experimental investigations or high-fidelity CFD simulations. On the other hand, less emphasis has been placed on creating control-oriented models that adopt a physics-based (rather than data-driven) approach to predict the onset of instability phenomena.

Nowadays, turbocharging is a technique widely used to improve fuel consumption and exhaust emissions in automotive engines. Centrifugal compressors are typically adopted, even if an efficient engine integration is often restricted by surge phenomena. The focus of the present work is to describe an experimental analysis developed with the aim at characterizing and identifying compressor behavior in incipient surge conditions. The acoustic and vibrational operative response of two automotive centrifugal compressors has been experimentally analyzed on the test facility operating at the University of Genoa. Each compressor is characterized by a classical architecture and one of them is equipped with a “ported shroud”, which enlarges stable zone. Compressors characteristic curves have been measured under steady flow conditions for different levels of corrected rotational speed from the choking region to the surge line.