Refine Your Search

Topic

Search Results

Standard

Engine Testing with Low-Temperature Charge Air-cooler Systems in a Dynamometer Test Cell

2011-09-06
CURRENT
J1937_201109
The methods presented in this SAE Recommended Practice apply to the controlled testing of low-temperature charge, air-cooled, heavy-duty diesel engines. This document encompasses the following main sections: a Definitions of pertinent parameters b Vehicle testing to determine typical values for these parameters c Description of the setup and operation of the test cell system d Validation testing of the test cell system While not covered in this document, computer modeling of the vehicle engine cooler system is recognized as a valid tool to determine cooler system performance and could be utilized to supplement the testing described. However, adequate in-vehicle testing should be performed to validate the model before it is used for the purposes outlined. The procedure makes references to test cycles that are prescribed by the United States Environmental Protection Agency (US EPA) and are contained in the Code of Federal Regulations.
Standard

Engine Testing With Low-Temperature Charge Air-Cooler Systems in a Dynamometer Test Cell

2002-10-21
HISTORICAL
J1937_200210
The methods presented in this SAE Recommended Practice apply to the controlled testing of low-temperature charge, air-cooled, heavy-duty diesel engines. This document encompasses the following main sections: a.) Definitions of pertinent parameters; b.) Vehicle testing to determine typical values for these parameters; c.) Description of the setup and operation of the test cell system; and d.) Validation testing of the test cell system. While not covered in this document, computer modeling of the vehicle engine cooler system is recognized as a valid tool to determine cooler system performance and could be utilized to supplement the testing described. However, adequate in-vehicle testing should be performed to validate the model before it is used for the purposes outlined. The procedure makes references to test cycles that are prescribed by the United States Environmental Protection Agency (US EPA) and are contained in the Code of Federal Regulations.
Standard

Engine Testing With Low-Temperature Charge Air-Cooler Systems in a Dynamometer Test Cell

1989-11-01
HISTORICAL
J1937_198911
The methods presented in this SAE Recommended Practice apply to the controlled testing of low-temperature charge, air-cooled, heavy-duty diesel engines. This document encompasses the following main sections: a.) Definitions of pertinent parameters; b.) Vehicle testing to determine typical values for these parameters; c.) Description of the setup and operation of the test cell system; d.) Validation testing of the test cell system. While not covered in this document, computer modeling of the vehicle engine cooler system is recognized as a valid tool to determine cooler system performance and could be utilized to supplement the testing described. However, adequate in-vehicle testing should be performed to validate the model before it is used for the purposes outlined. The procedure makes references to test cycles that are prescribed by the United States Environmental Protection Agency (US EPA) and are contained in the Code of Federal Regulations.
Standard

Reporting on Emission Testing for In-Use Light-Duty Trucks and Passenger Vehicles

2001-06-27
CURRENT
J1712_200106
This SAE Recommended Practice applies to the reporting of laboratory and test site data from the gaseous and evaporative emission tests of in-use light duty trucks and passenger vehicles. This document describes the reporting of procedures, fuel specifications, and vehicle information necessary to compare the results of in-use tests. Any variations in vehicles, instrumentation, test equipment, or test program purpose should be adequately described.
Standard

Reporting on Emission Testing for In-Use Light-Duty Trucks and Passenger Vehicles

2000-10-01
HISTORICAL
J1712_200010
This SAE Recommended Practice applies to the reporting of laboratory and test site data from the gaseous and evaporative emission tests of in-use light duty trucks and passenger vehicles. This document describes the reporting of procedures, fuel specifications, and vehicle information necessary to compare the results of in-use tests. Any variations in vehicles, instrumentation, test equipment, or test program purpose should be adequately described.
Standard

Lip Force Measurement--Radial Lip Seals

1988-06-01
HISTORICAL
J1901_198806
This SAE Recommended Practice defines radial lip force for shaft seals. The principle of lip force measurement is described and the types of radial force measuring devices are discussed. A type of radial force measuring device and procedure for use is recommended.
Standard

Impact of Alternative Fuels on Engine Test and Reporting Procedures

1988-03-01
HISTORICAL
J1515_198803
The guidelines in this SAE Information Report are directed at laboratory engine dynamometer test procedures with alternative fuels, and they are applicable to four-stroke cycle spark ignition (SI) and diesel (CI) engines (naturally aspirated or pressure charged, with or without charge air cooling). A brief overview of investigations with some alternative fuels can be found in SAE J1297. Other SAE documents covering vehicle, engine, or component testing may be affected by use of alternative fuels. Some of the documents that may be affected can be found in Appendix A. Guidelines are provided for the engine power test code (SAE J1349) in Appendix D. The principles of these guidelines may apply to other procedures and codes, but the effects have not been investigated. The report is organized into four technical sections, each dealing with an important aspect of testing or reporting of results when using alternative fuels.
Standard

Emission Test Driving Schedules

2002-10-21
CURRENT
J1506_200210
This SAE Information Report describes various dynamometer driving schedules currently in use in the world for measurement of exhaust emissions and fuel economy of passenger cars and light trucks. Issuance of this document will allow driving schedules to be deleted from individual test procedures, thus reducing the amount of repeated information in the SAE Handbook. This document includes: a.) Descriptions of driving schedules and b.) Second-by-second definition of speed versus time sequences.
Standard

Emission Test Driving Schedules

1988-06-01
HISTORICAL
J1506_198806
This SAE Information Report describes various dynamometer driving schedules currently in use in the world for measurement of exhaust emissions and fuel economy of passenger cars and light trucks. Issuance of this document will allow driving schedules to be deleted from individual test procedures, thus reducing the amount of repeated information in the SAE Handbook. This document includes: a.) Descriptions of driving schedules and b.) Second-by-second definition of speed versus time sequences.
Standard

Emission Test Driving Schedules

1991-06-01
HISTORICAL
J1506_199106
This SAE Information Report describes various dynamometer driving schedules currently in use in the world for measurement of exhaust emissions and fuel economy of passenger cars and light trucks. Issuance of this document will allow driving schedules to be deleted from individual test procedures, thus reducing the amount of repeated information in the SAE Handbook. This document includes: a.) Descriptions of driving schedules and b.) Second-by-second definition of speed versus time sequences.
Standard

Continuous Hydrocarbon Analysis of Diesel Emissions

2002-10-21
CURRENT
J215_200210
The method presented is the current recommendation for the use of flame ionization detectors to determine the hydrocarbon content of diesel engine exhaust, or exhaust of vehicles using diesel engines, when operating at steady-state. The requirements of the associated sampling system and a general procedure for a continuous measuring method are presented. This SAE Recommended Practice provides for the continuous measurement of the hydrocarbon concentration in diesel exhaust.
Standard

Manual Transmissions and Transaxle High-speed Lubrication, Unbalance, and Seizure Evaluation

2011-09-06
CURRENT
J2132_201109
It is anticipated that this SAE Recommended Practice will be only one step in a comprehensive evaluation of the vehicle/transmission application. This document alone is not adequate “due care” to insure against high-speed seizure or other high-speed problems. The notes printed in bold print throughout the practice convey important information about the test itself or the results and should be considered carefully. All references to transmissions also apply to transaxles, except for the unbalance evaluation which applies only to rear-wheel-drive transmissions with propeller shaft output.
Standard

Measurement of Intake Air or Exhaust Gas Flow of Diesel Engines

2011-06-13
CURRENT
J244_201106
This procedure establishes recommendations on the measurement of diesel engine intake air flow under steady-state test conditions. The measurement methods discussed have been limited to metering systems and associated equipment found in common usage in the industry, specifically, nozzles, laminar flow devices, and vortex shedding. The procedure establishes accuracy goals as well as explains proper usage of equipment. The recommendations concerning diesel engine exhaust mass flow measurements are minimal in scope.
Standard

Manual Transmission and Transaxle Efficiency and Parasitic Loss Measurement

2011-09-02
CURRENT
J2453_201109
Because of the intense focus on CAFE and fuel emission standards, optimization of the automobile drivetrain is imperative. In light of this, component efficiencies have become an important factor in the drivetrain decision-making process. It has therefore become necessary to develop a universal standard to judge transmission efficiency. This SAE Recommended Practice specifies the dynamometer test procedure which maps a manual transmission’s efficiency. The document is separated into two parts. The first compares input and output torque throughout a specified input speed range in order to determine “in-gear” transmission efficiency. The second procedure measures parasitic losses experienced while in neutral at nominal idling speeds and also churning losses while in gear. The application of this document is intended for passenger car and light truck. All references to transmissions throughout this document include transaxles.
Standard

Crankcase Emission Control Test Code

2012-01-23
CURRENT
J900_201201
The purpose of this SAE STandard is to provide standard test procedures for crankcase emission control systems and/or devices. The procedures included are for determining: a. The flow rate of the blowby of an engine; b. The flow rates through the crankcase emission control system inlet and outlet. This code is written to cover crankcase emission control systems which are designed to reduce the emission of engine blowby gases to the atmosphere. The code includes the following sections: 3. Definitions and Terminology; 4. Test Equipment; 5. Test Procedures; 6. Information and Data to be Recorded; 7. Data Analysis; 8. Presentation of Information and Data.
Standard

Crankcase Emission Control Test Code

1995-03-01
HISTORICAL
J900_199503
The purpose of this SAE STandard is to provide standard test procedures for crankcase emission control systems and/or devices. The procedures included are for determining: a. The flow rate of the blowby of an engine; b. The flow rates through the crankcase emission control system inlet and outlet. This code is written to cover crankcase emission control systems which are designed to reduce the emission of engine blowby gases to the atmosphere. The code includes the following sections: 3. Definitions and Terminology; 4. Test Equipment; 5. Test Procedures; 6. Information and Data to be Recorded; 7. Data Analysis; 8. Presentation of Information and Data.
Standard

Crankcase Emission Control Test Code

1980-11-01
HISTORICAL
J900_198011
The purpose of this SAE STandard is to provide standard test procedures for crankcase emission control systems and/or devices. The procedures included are for determining: a. The flow rate of the blowby of an engine; b. The flow rates through the crankcase emission control system inlet and outlet. This code is written to cover crankcase emission control systems which are designed to reduce the emission of engine blowby gases to the atmosphere. The code includes the following sections: 3. Definitions and Terminology; 4. Test Equipment; 5. Test Procedures; 6. Information and Data to be Recorded; 7. Data Analysis; 8. Presentation of Information and Data.
Standard

Crankcase Emission Control Test Code

1985-08-01
HISTORICAL
J900_198508
The purpose of this SAE STandard is to provide standard test procedures for crankcase emission control systems and/or devices. The procedures included are for determining: a. The flow rate of the blowby of an engine; b. The flow rates through the crankcase emission control system inlet and outlet. This code is written to cover crankcase emission control systems which are designed to reduce the emission of engine blowby gases to the atmosphere. The code includes the following sections: 3. Definitions and Terminology; 4. Test Equipment; 5. Test Procedures; 6. Information and Data to be Recorded; 7. Data Analysis; 8. Presentation of Information and Data.
Standard

Crankcase Emission Control Test Code

1964-06-01
HISTORICAL
J900_196406
The purpose of this SAE STandard is to provide standard test procedures for crankcase emission control systems and/or devices. The procedures included are for determining: a. The flow rate of the blowby of an engine; b. The flow rates through the crankcase emission control system inlet and outlet. This code is written to cover crankcase emission control systems which are designed to reduce the emission of engine blowby gases to the atmosphere. The code includes the following sections: 3. Definitions and Terminology; 4. Test Equipment; 5. Test Procedures; 6. Information and Data to be Recorded; 7. Data Analysis; 8. Presentation of Information and Data.
Standard

Application Guide to Radial Lip Seals

2002-10-25
CURRENT
J946_200210
This SAE Recommended Practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of oil seals.
X