Refine Your Search

Date

Date

Topic

Topic

SAE IC Powertrain Steering Committee Aluminum alloys Data management

Search Results

Viewing 1 to 20 of 25
12Next >Last >>
Sort by published
Standard

Engine Flywheel Housings with Sealed Flanges
2012-10-23
CURRENT
J1172_201210
This SAE Recommended Practice defines flywheel housing flange configurations for applications requiring "O" ring sealing of the flange pilot bore. Table 1 and Figure 1 show dimensions that are different from those in SAE J617. All other dimensions and tolerances of SAE J617 apply.
Standard

TURBOCHARGER NOMENCLATURE AND TERMINOLOGY
1979-11-01
HISTORICAL
J922_197911
This recommended practice applies to nomenclature of turbo-charger parts and terminology of performance. Modifying adjectives are omitted in some cases for the sake of simplicity. However, it is considered good practice to use such adjectives when they add to clarity and understanding.
Standard

APPLICATION GUIDE TO RADIAL LIP SEALS
1989-08-01
HISTORICAL
J946_198908
This recommended practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally-accepted information and data. The main reason for the preparation of the recommended practice is to make standard information available in one document to the users of oil seals.
Standard

APPLICATION GUIDE TO RADIAL LIP SEALS
1991-10-01
HISTORICAL
J946_199110
This SAE Recommended Practice is intended as a guide to the use of radial lip type seals. It has been prepared from existing literature, which includes standards, specifications, and catalog data of both oil seal producers and users and includes generally accepted information and data. The main reason for the preparation of the document is to make standard information available in one document to the users of oil seals.
Standard

Housing Internal Dimensions for Single- and Two-Plate Spring-Loaded Clutches
2012-05-31
CURRENT
J373_201205
This SAE Recommended Practice defines the minimum internal dimensions for clutch housings to provide adequate clearance for single- and two-plate spring-loaded clutches. (See Figure 1.) Consult SAE J617 for housing flange dimensions. Consult SAE J618 and J619 for spring-loaded clutch flywheel dimensions F and G and other dimensional data. Table 1 provides housing minimum internal dimensions for single- and two-plate spring-loaded clutches.
Standard

FLYWHEELS FOR TWO-PLATE SPRING-LOADED CLUTCHES
1993-12-01
HISTORICAL
J619_199312
This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for dry spring-loaded clutches. Clutches to fit flywheels with configurations per this document may not be commercially available. Availability should be ascertained prior to flywheel design Figure 1 and Table 1A.
Standard

Flywheels for Two-Plate Spring-Loaded Clutches
2012-05-31
CURRENT
J619_201205
This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for dry spring-loaded clutches. Clutches to fit flywheels with configurations per this document may not be commercially available. Availability should be ascertained prior to flywheel design Figure 1 and Table 1A.
Standard

Design Guide for Formed-in-Place Gaskets
2008-07-08
CURRENT
J1497_200807
This SAE Recommended Practice presents information which is intended as a guide for proper designing, selection, application, and servicing of liquid, formed-in-place gasket (FIPG) materials.
Standard

INDUSTRIAL POWER TAKE-OFFS WITH DRIVING RING-TYPE OVERCENTER CLUTCHES
1995-03-08
HISTORICAL
J621_199503
This SAE Standard defines installation dimensions of industrial power take-offs with driving ring-type overcenter clutches. Table 1 and Figure 1 give dimensions for power take-offs. For dimensions and tolerances of power take-off flanges and flywheels, see SAE J617 and J620, respectively.
Standard

Industrial Power Take-Offs With Driving Ring-Type Overcenter Clutches
2012-10-23
CURRENT
J621_201210
This SAE Standard defines installation dimensions of industrial power take-offs with driving ring-type overcenter clutches. Table 1 and Figure 1 give dimensions for power take-offs. For dimensions and tolerances of power take-off flanges and flywheels, see SAE J617 and J620, respectively.
12Next >Last >>
X