Search Results

In the next years, the upcoming emission legislations are expected to introduce further restrictions on the admittable level of pollutants from vehicles measured on homologation cycles and real drive tests. In this context, the strict control of pollutant emissions at the cold start will become a crucial point to comply with the new regulation standards. This will necessarily require the implementation of novel strategies to speed-up the light-off of the reactions occurring in the after-treatment system, since the cold start conditions are the most critical one for cumulative emissions. Among the different possible technological solutions, this paper focuses on the evaluation of the potential of a burner system, which is activated before the engine start. The hypothetical burner exploits the lean combustion of an air-gasoline mixture to generate a high temperature gas stream which is directed to the catalyst section promoting a fast heating of the substrate.

The selective catalytic reduction has seen widespread adoption as the best technology to reduce the NOx emissions from internal combustion engines, particularly for Diesels. This technology uses ammonia as a reducing agent, which is obtained injecting an ammonia carrier into the exhaust gas stream. The dosing of the ammonia carrier, usually AdBlue, is the major concern during the design and engine calibration phases, since the interaction between the injected liquid and the components of the exhaust system can lead to the undesired formation of solid deposits. To avoid this, the thermal and kinematic interaction between the spray and the components of the after treatment system (ATS) must be modeled accurately. In this work, the authors developed a Conjugate Heat Transfer (CHT) framework to model the kinetic and thermal interaction among the spray, the eventual liquid layer and the pipe walls.

In the last few years, the effect of diabatic test conditions on compressor performance maps has been widely investigated, leading some Authors to propose different correction models. The accuracy of turbocharger performance map constitute the basis for the tuning and validation of a numerical method, usually adopted for the prediction of engine-turbocharger matching. Actually, it is common practice in automotive applications to use simulation codes, which can either require measured compression ratio and efficiency maps as input values or calculate them “on the fly” throughout specific sub-models integrated in the numerical procedures. Therefore, the ability to correct the measured performance maps taking into account internal heat transfer would allow the implementation of commercial simulation codes used for engine-turbocharger matching calculations.

In the last few years, the effect of diabatic test conditions on compressor performance maps has been widely investigated leading some Authors to propose different correction models. The aim of the paper is to investigate the effect of heat transfer phenomena on the experimental definition of turbocharger maps, focusing on turbine performance. An experimental investigation on a small turbocharger for automotive application has been carried out and presented. The study focused onto the effects of internal heat transfer on turbine thermomechanical efficiency. The experimental campaign was developed considering the effect of different heat transfer state by varying turbine inlet temperature, oil and coolant temperature and compressor inlet pressure. An original model previously developed by the Authors is adopted for the correction of compressor steady flow maps.

In the last years, as a response to the more and more restrictive emission legislation, new devices (SRC, DOC, NOx-trap, DPF) have been progressively introduced as standard components of modern after-treatment system for Diesel engines. In addition, the adoption of electrical heating is nowadays regarded with interest as an effective solution to promote the light-off of the catalyst at low temperature, especially at the start-up of the engine and during the low load operation of the engine typical of the urban drive. In this work, a state-of-the-art 48 V electrical heated catalyst is considered, in order to investigate its effect in increasing the abatement efficiency of a standard DOC. The electrical heating device considered is based on a metallic support, arranged in a spiral layout, and it is heated by the Joule effect due to the passage of the electrical current.

Turbocharging is playing today a fundamental role not only to improve automotive engine performance, but also to reduce fuel consumption and exhaust emissions for both Spark Ignition and Diesel engines. Dedicated experimental investigations on turbochargers are therefore necessary to assess a better understanding of its performance. The availability of experimental information on turbocharger steady flow performance is an essential requirement to optimize the engine-turbocharger matching, which is usually achieved by means of simulation models. This aspect is even more important when referred to the turbine efficiency, since its swallowing capacity can be accurately evaluated through the measurement of mass flow rate, inlet temperature and pressure ratio across the machine.

This work describes the development of a computational model for the CFD simulation of compact heat exchangers applied for the oil cooling in internal combustion engines. Among the different cooler types, the present modeling effort will be focused on liquid-cooled solutions based on offset strip fins turbulators. The design of this type of coolers represents an issue of extreme concern, which requires a compromise between different objectives: high compactness, low pressure drop, high heat-transfer efficiency. In this work, a computational framework for the CFD simulation of compact oil-to-liquid heat exchangers, including offset-strip fins as heat transfer enhancer, has been developed. The main problem is represented by the need of considering different scales in the simulation, ranging from the characteristic size of the turbulator geometry (tipically μm - mm) to the full scale of the overall device (typically cm - dm).

The transient heat transfer behavior of an automotive catalytic converter has been simulated with OpenFOAM in 1D. The model takes into consideration the gas-solid convective heat transfer, axial wall conduction and heat capacity effects in the solid phase, but also the chemical reactions of CO oxidation, based on simplified Arrhenius and Langmuir-Hinshelwood approaches. The associated parameters are the results of data in literature tuned by experiments. Simplified cases of constant flow rates and gas temperatures in the catalyst inflow have been chosen for a comprehensive analysis of the heat and mass transfer phenomena. The impact of inlet flow temperatures and inlet flow rates on the heat up characteristics as well as in the CO emissions have been quantified. A dimensional analysis is proposed and dimensionless temperature difference and space-time coordinates are introduced.

The isentropic efficiency estimation of small radial turbines is an important aspect of turbocharger performance evaluation. Because of inaccuracies in measuring the outlet temperature due to the non-homogeneous flow field distribution, it is common practice to refer to the thermomechanical efficiency, defined as the product of mechanical and turbine isentropic efficiencies. This paper proposes a method for the indirect evaluation of turbine isentropic efficiency through specific experimental tests. In particular, the evaluation of friction losses in the bearings can be assessed thanks to experimental investigations in quasi-adiabatic condition. By maintaining the turbine inlet temperature and the average temperature of lubricating oil and water-cooling circuit equal to the compressor outlet temperature, a negligible heat transfer between turbine and compressor can be achieved.

Turbochargers are still one of the most common solutions to improve internal combustion engines performance. The correct evaluation of turbochargers characteristic maps is one of the main issues to achieve a good matching with internal combustion engines. In a 1D procedure the accuracy of performance maps constitutes the basis of the turbocharger matching with the engine. The classical quasi-steady approach assumes that compressor and turbine characteristic maps are evaluated under the hypothesis of adiabatic turbocharger behavior. The aim of the paper is the investigation of the effect of heat transfer phenomena on the measured turbocharger maps. A model to correct compressor efficiency evaluated starting from measured data, thus removing the heat transfer effects, is proposed. The compressor steady flow behavior has been analyzed through specific tests performed at the test rig for components of propulsion systems of the University of Genoa, under various heat transfer conditions.

In the last few years, the effect of diabatic test conditions on compressor performance maps has been widely investigated leading some authors to propose different correction models. The accuracy of performance maps constitutes the basis of the turbocharger matching with the engine, for which 1D procedures are more and more adopted. The classical quasi-steady approach generally used is based on the employment of compressor and turbine characteristic maps assuming adiabatic turbocharger conditions. The aim of the paper is to investigate the effect of heat transfer phenomena on the experimental definition of turbocharger maps, focusing on compressor performance. This work was developed within a collaboration between the Polytechnic School of the University of Genoa and CRITT M2A. The compressor steady flow behavior was analyzed through tests performed on different test rigs operating at the University of Genoa and at CRITT M2A, under various heat transfer conditions.

The target of the upcoming automotive emission regulations is to promote a fast transition to near-zero emission vehicles. As such, the range of ambient and operating conditions tested in the homologation cycles is broadening. In this context, the proposed work aims to thoroughly investigate the potential of post-oxidation phenomena in reducing the light-off time of a conventional three-way catalyst. The study is carried out on a turbocharged four-cylinder gasoline engine by means of experimental and numerical activities. Post oxidation is achieved through the oxidation of unburned fuel in the exhaust line, exploiting a rich combustion and a secondary air injection dedicated strategy. The CFD methodology consists of two different approaches: the former relies on a full-engine mesh, the latter on a detailed analysis of the chemical reactions occurring in the exhaust line.

The reduction of the catalyst light-off time at the engine cold start represents a key factor for the pollutant emissions control from vehicles tested on homologation cycles and real drive conditions. The adoption of heating strategies to increase the temperature of the catalytic substrate in the early phase of the engine start is regarded as a promising solution. The present study focuses on the application of electrical heated catalyst (EHC) in an after-treatment line for a spark-ignition gasoline engine. The analysis is carried out by means of an advanced CFD framework, which includes the modeling of catalytic reactions in the substrates and accounts for the thermal evolution of all the components included in the after-treatment system.