Refine Your Search

Search Results

Viewing 1 to 10 of 10
Technical Paper

Validation of the SIMON Model for Vehicle Handling and Collision Simulation - Comparison of Results with Experiments and Other Models

2004-03-08
2004-01-1207
SIMON is a new 3-dimensional vehicle dynamic simulation model. The capabilities of the model include non-linear handling maneuvers and collision simulation for one or more vehicles. As a new model, SIMON must be validated by comparison against actual handling and collision experiments. This paper provided that comparison. Included in the validation were lane-change maneuvers, alternate ramp traversals, limit maneuvers with combined braking and steering, vehicle-to-vehicle crash tests and articulated vehicle handling tests. Comparison against other models were included. No metric was provided for handling test comparisons. However, statistical analysis of the collision test results revealed the average path range error was 6.2 to 14.8 percent. The average heading error was -4.7 to 0.7 percent. Delta-V error was -1.6 to 7.5 percent. VEHICLE SIMULATION has many uses in the vehicle design and safety industries.
Technical Paper

Single Vehicle Wet Road Loss of Control; Effects of Tire Tread Depth and Placement

2002-03-04
2002-01-0553
When an automobile is driven on wet roads, its tires must remove water from between the tread and road surfaces. It is well known that the ability of a tire to remove water depends heavily on tread depth, water depth and speed, as well as other factors, such as tire load, air pressure and tread design. It is less well known that tire tread depth combined with placement can have an adverse effect on vehicle handling on wet roads. This paper investigates passenger car handling on wet roads. Flat bed tire testing, three-dimensional computer simulation and skid pad experimental testing are used to determine how handling is affected by tire tread depth and front/rear position of low-tread-depth tires on the vehicle. Some skid pad test results are given, along with corresponding simulations. A literature review also is presented. Significant changes in tire-road longitudinal and lateral friction are shown to occur as speed, tread depth and water depth vary, even before hydroplaning occurs.
Technical Paper

Validation of DyMESH for Vehicle vs Barrier Collisions

2000-03-06
2000-01-0844
A new three-dimensional collision simulation algorithm, called DyMESH (Dynamic MEchanical SHell) was recently introduced.[1]* This paper presents a validation of DyMESH for vehicle vs. barrier collisions. The derivation of the three-dimensional force vs. crush relationship was described previously.[1] Here the application of three-dimensional force vs. crush curves using the outlined methodology is shown to be effective. Nonlinear force versus crush relationships are introduced for use in DyMESH. Included are numerous DyMESH collision simulations of several types of vehicles (e.g., light and heavy passenger car and sport utility) compared directly with experimental collision test results from various types of barrier tests (e.g., full frontal, angled frontal, and offset frontal). The focus here is not on the vehicle’s change in velocity, but on the acceleration vs. time history.
Technical Paper

An Overview of the EDSMAC4 Collision Simulation Model

1999-03-01
1999-01-0102
The EDSMAC simulation model has been in widespread use by vehicle safety researchers since its introduction in 1985. Several papers have been published that describe the model and provide validations of its use. In 1997, the collision and vehicle dynamics models were extended significantly. The main control logic was also extended and generalized. The resulting model was named EDSMAC4. This paper describes the EDSMAC4 model with particular attention to the extensions to the original algorithms. The paper also provides a validation of the new model by direct comparison to staged collision experiments and the results from the previous EDSMAC model.
Technical Paper

An Overview of the Way EDCRASH Computes Delta-V

1987-02-01
870045
The two procedures, DAMAGE and OBLIQUE IMPACT, which are used by EDCRASH for computing delta-V, are described in detail. Enhancements in EDCRASH Version 4 which improve the DAMAGE method of computing delta-V are also described. The advantages and disadvantages of each method are explored, and the numerical and graphical output and use of warning messages are reviewed. In general, it was found the two methods are complimentary: The DAMAGE procedure is best-suited for the conditions in which the OBLIQUE IMPACT procedure is least-suited, and vice-versa.
Technical Paper

An Overview of the Way EDSMAC Computes Delta-V

1988-02-01
880069
The EDSMAC personal computer program for use by accident investigators is described. The input data requirements are reviewed. The general calculation procedures are discussed and the specific procedures for computing delta-V are explained in detail. The method, based on equalizing the force between the vehicles at all times during the impact phase, is seen to be simple in concept but extremely complex in practice. The numerical and graphical output and warning messages are reviewed. Applications of the program are illustrated. The major benefit of EDSMAC is the ability, using graphics, to provide an analytical method illustrating how an accident may, or may not, have occurred.
Technical Paper

An Overview of the HVE Developer's Toolkit

1994-03-01
940923
A substantial programming effort is required to develop a human or vehicle dynamics simulator. More than half of this effort is spent designing and programming the user interface (the means by which the user supplies program input and views program output). This paper describes a pre-programmed, 3-dimensional (3-D), input/output window-type interface which may be used by developers of human and vehicle dynamics programs. By using this interface, the task of input/output programming is reduced by approximately 50 percent, while simultaneously providing a more robust interface. This paper provides a conceptual overview of the interface, as well as specific details for writing human and vehicle dynamics programs which are compatible with the interface. Structures are provided for the human, vehicle and environment models. Structures are also provided for events, interface variables, and the output data stream.
Technical Paper

An Overview of the HVE Human Model

1995-02-01
950659
Developers of human dynamics simulation software inherently use a mathematical/physical model to represent the human. This paper describes a pre-programmed, object-oriented human model for use in human dynamics simulations. This human model is included as part of an integrated simulation environment, called HVE (Human-Vehicle-Environment), described in previous research. The current paper first provides a general overview of the HVE user and development environments, and then provides detailed specifications for the HVE Human Model. These specifications include definitions for model parameters (supported human types and human properties, such as dimensions, inertias, joints and injury tolerances). The paper also provides detailed specifications for the HVE time-dependent human output group parameters (kinematics, joints, contacts, belts and airbags).
Technical Paper

An Overview of the HVE Vehicle Model

1995-02-01
950308
Developers of vehicle dynamics simulation software inherently use a mathematical/physical model to represent the vehicle. This paper describes a pre-programmed, object-oriented vehicle model for use in vehicle dynamics simulations. This vehicle model is included as part of an integrated simulation environment, called HVE (Human-Vehicle-Environment), described in previous research [1,2] *. The current paper first provides a general overview of the HVE user and development environments, and then provides detailed specifications for the HVE Vehicle Model. These specifications include definitions for model parameters (supported vehicle types; vehicle properties, such as dimensions, inertias, suspensions; tire properties, such as dimensions and inertias, mu vs slip, cornering and camber stiffnesses; driver control systems, such as engine, transmission/differential, brakes and steering; restraint systems, such as belts and airbags).
Technical Paper

3-Dimensional Simulation of Vehicle Response to Tire Blow-outs

1998-02-23
980221
Sudden tire deflation, or blow-out, is sometimes cited as the cause of a crash. Safety researchers have previously attempted to study the loss of vehicle control resulting from a blow-out with some success using computer simulation. However, the simplified models used in these studies did little to expose the true transient nature of the handling problem created by a blown tire. New developments in vehicle simulation technology have made possible the detailed analysis of transient vehicle behavior during and after a blow-out. This paper presents the results of an experimental blow-out study with a comparison to computer simulations. In the experiments, a vehicle was driven under steady state conditions and a blow-out was induced at the right rear tire. Various driver steering and braking inputs were attempted, and the vehicle response was recorded. These events were then simulated using EDVSM. A comparison between experimental and simulated results is presented.
X