Refine Your Search

Search Results

Standard

Test Method for Determining Cold Cracking of Flexible Plastic Materials

2009-11-09
CURRENT
J323_200911
This SAE Recommended Practice is applicable for determining the cold characteristics of flexible plastic materials, as applicable. It consists of three different methods for determining low-temperature properties of materials depending on type of material and end use. The method used shall be as specified by the contractual parties.
Standard

Fiberboard Test Procedure

2010-03-02
CURRENT
J315_201003
This SAE Standard provides test methods for determining the critical characteristics of basic or finished fiberboard products. Where applicable, methods of test developed by SAE and ASTM have been referenced.
Standard

Standard Classification System for Fiberboards

2014-06-04
CURRENT
J1323_201406
This SAE Standard provides a means for specifying or describing the pertinent properties of fiberboards for automotive applications. The materials normally specified by this standard are defined in SAE J947. The test methods commonly used for fiberboards are defined in SAE J315.
Standard

Fiberboard Crease Bending Test

2010-05-10
CURRENT
J119_201005
This test method is designed to determine the suitability of a painted or unpainted fiberboard for application involving creasing and bending. The specific purpose of the test is to determine whether a given material, properly creased, can be bent along the impressed crease without objectionable failure on the surface of the bend.
Standard

Method of Testing Resistance to Crocking of Organic Trim Materials

2012-08-24
CURRENT
J861_201208
This test can be used to determine the resistance to crocking (color rub-off) of organic trim materials such as fabrics, vinyl coated fabrics, leather, coated fiberboard and carpet. This method is similar to AATCC Method 8 –Colorfastness to Crocking.
Standard

Test Method for Determining Blocking Resistance and Associated Characteristics of Automotive Trim Materials

2012-10-15
CURRENT
J912_201210
This test method is designed to indicate the degree of surface tackiness, color transfer, loss of embossment, and surface marring when two trim materials are placed face to face under specific conditions of time, temperature, and pressure. These specific conditions are not dictated in this test procedure but will be found in the material standards which govern each type of trim material to be tested.
Standard

Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Water Cooled Xenon-Arc Apparatus

2008-01-11
CURRENT
J1885_200801
This test method specifies the operating procedures for a controlled irradiance, water cooled xenon-arc apparatus used for the accelerated exposure of various automotive interior trim components. Test durations, as well as any exceptions to the sample preparation and performance evaluation procedures contained in this document, are covered in material specifications of the different automotive manufacturers. This standard is limited to the models of xenon arc test apparatus specified in the Section on Equipment. All other models of xenon arc test apparatus must use SAE J2412 to perform the test conditions specified in SAE J1885. SAE J2412 is the performance standard based on the test parameters of SAE J1885. Use of xenon arc test apparatus to perform SAE J2412 must be agreed upon by contractual parties.
Standard

Design Guidelines for Fiberboard Materials

2010-06-21
CURRENT
J1774_201006
This document provides information on the various fiberboard products, which are available for automotive application. It is intended to give engineers and designers a better understanding of product usage, characteristics, properties and industry terminology. The following sections cover these topics: 2 General Product Information 3 Design Characteristics 4 Physical/Mechanical Properties 5 Fiberboard Definitions In sections 2, 3 and 4 the fiberboard products are categorized. These sections give an overview of product types, with general information about characteristics and properties. In cases where product categories encompass more than one material or material grade, ranges were established to cover all of the products in that category. The individual companies that supply fiberboard products should be consulted for specific information about a particular product or application.
Standard

Procedure for Visual Evaluation of Interior and Exterior Automotive Trim

2013-08-14
HISTORICAL
J361_201308
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim.
Standard

Procedure for Visual Evaluation of Interior and Exterior Automotive Trim

2017-04-17
CURRENT
J361_201704
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100 Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
Standard

Procedure for Visual Evaluation of Interior and Exterior Automotive Trim

2016-11-18
HISTORICAL
J361_201611
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
Standard

Test for Chip Resistance of Surface Coatings

2012-10-23
CURRENT
J400_201210
This SAE Recommended Practice covers a laboratory procedure for testing and evaluating the resistance of surface coating to chipping by gravel impact. The test is designed to reproduce the effect of gravel or other media striking exposed paint or coated surfaces of an automobile and has been correlated with actual field results. The specific intent of the test is to evaluate organic surface coatings or systems on flat test panels; however, It may be possible to extend this type of testing to finished parts or other types of materials such as anodized aluminum or plated plastics if the results are interpreted with respect to the limitations and intent implied by the original testing procedures and rating system. This document may involve hazardous materials, operations, and equipment. This document does not purport to address all of the safety problems associated with its use.
Standard

Instrumental Color Difference Measurement for Exterior Finishes, Textiles and Colored Trim

2005-07-25
HISTORICAL
J1545_200507
The practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials that are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film.
X