Search Results

The objective of the work reported in this paper was to develop and demonstrate an injection nozzle which can be used to inject both diesel fuel and methanol in to a direct injection diesel engine. The constraints on the nozzle were that it must provide acceptable fuel metering and atomization for the diesel fuel so that the engine can be operated at rated load on diesel fuel alone, or operate at full load with the diesel fuel as a pilot for the methanol. An additional constraint was that the nozzle design was to be easily adaptable to the existing injection nozzle so that engine head modifications are not required. The initial design was evaluated in a constant volume test chamber in which the pressure was varied from atmospheric to engine compression pressures.

Mixtures of methanol, water and heavier alcohols, simulating “raw’ methanol at various levels of processing, were tested in a constant volume combustion apparatus (CVCA) and in a single-cylinder, direct-injection diesel engine. The ignition characteristics determined in the CVCA indicated that the heavier alcohols have beneficial effects on the auto-ignition quality of the fuels, as compared to pure methanol. Water, at up up to 10 percent by volume, has little effect on the ignition quality. In all cases, however, the cetane numbers of the alcohol mixtures were very low. The same fuels were tested in a single cylinder engine, set-up in a configuration similar to current two-valve DI engines, except that the compression ratio was increased to 19:1. Pure methanol and five different blends of alcohols and water were tested in the engine at five different speed-load conditions.

Biodiesel is a mixture of esters (usually methyl esters) of fatty acids found in the triglycerides of vegetable oils. The different fatty compounds comprising biodiesel possess different ignition properties. To investigate and potentially improve these properties, the cetane numbers of various fatty acids and esters were determined in a Constant Volume Combustion Apparatus. The cetane numbers range from 20.4 for linolenic acid to 80.1 for butyl stearate. The cetane numbers depend on the number of CH2 groups as well as the number of double bonds and other factors. Various oxygenated compounds were studied for their potential of improving the cetane numbers of fatty compounds. Several potential cetane improvers with ignition delay properties giving calculated cetane numbers over 100 were identified. The effect of these cetane improvers depended on their concentration and also on the fatty material investigated.

A 2003 heavy-duty diesel engine (2002 emissions level) was used to test a representative biodiesel fuel as well as the methyl esters of several different fatty acids. The fuel variables included degree of saturation, the oxygen content, and carbon chain length. In addition, two pure normal paraffins with the corresponding chain lengths of two of the methyl esters were also tested to determine the impact of chain length. The dependent variables were the NOx and the particulate emissions (PM). The results indicated that the primary fuel variable affecting the emissions is the oxygen content. The emissions results showed that the highest oxygen content test fuel had the lowest emissions of both NOx and PM. As compared to the baseline diesel fuel the NOx emissions were reduced by 5 percent and the PM emissions were reduced by 83 percent.

It is now a fairly well established fact that excessive ring and cylinder bore wear can result from the operation of an S. I. engine on neat methanol. The mechanism leading to the excessive wear were investigated using both engine and bench tests. Engine tests using prevaporized superheated methanol indicated that the wear results from reactions between the combustion products and the cast iron cylinder liner, where the presence of liquid methanol in the combustion chamber appears to be an important part of the mechanism. These reactions were investigated using a spinning disc combustor. The spinning disc combustor was used to provide a source of burning methanol droplets which were subsequently quenched on a water-cooled cast iron surface. The condensate formed on the cast iron surface was collected and analyzed for chemical composition. Infrared analysis indicated the presence of large quantities of iron formate, a reaction product of iron and formic acid.

Hybrids are fuels derived from combinations of different energy sources and which are generally formulated as solutions, emulsions, or slurries. The underlying objective of this program is to reduce the use of petroleum-derived fuels and/or to minimize the processing requirements of the finished hybrid fuels. Several hybrid fuel formulations have been developed and tested in a direct injection single-cylinder diesel engine. The formulations included solutions of ethanol and vegetable oils in diesel fuel, emulsions of methanol and of ethanol in diesel fuel; and slurries of starch, cellulose, and “carbon” in diesel fuel. Based on the progress to date, the solutions and emulsions appear to be viable diesel engine fuels if the economic factors are favorable and the storage and handling problems are not too severe. The slurries, on the other hand, are not to the same point of development as the solutions and emulsions.

A constant volume bomb was used to determine basic combustion characteristics of isooctane, n-heptane, methanol, propane and methane. Results show that the laminar flame velocity of a quiescent homogeneous air/fuel mixture can be derived from pressure-time data in the bomb. The effects of pressure, temperature, and charge dilution on flame velocity and ignition are presented. A thermo-chemical kinetic model accurately predicted concentrations of nitric oxide during combustion and in the burned gas.

One of the major problems created by the use of methanol fuels in SI engines is the high cylinder bore and ring wear rates observed during operation at low engine temperatures. The objective of the work reported in this paper was to identify the processes controlling the corrosion/wear mechanism in methanol-fueled, spark-ignition engines. Basically, three different types of experiments were performed during this project. The experiments consisted of: 1. Combustion experiments designed to identify the combustion products of methanol at various locations within a confined methanol flame; 2. Exposure studies designed to define the specific role of each of the combustion products on the corrosion mechanism; 3. Lubricant screening experiments designed to identify the mode of penetration of the oil film, and the location, in the microscale, of the surface attack. Performic acid was identified as the corrosive agent.