Search Results

The objective of the work reported in this paper was to develop and demonstrate an injection nozzle which can be used to inject both diesel fuel and methanol in to a direct injection diesel engine. The constraints on the nozzle were that it must provide acceptable fuel metering and atomization for the diesel fuel so that the engine can be operated at rated load on diesel fuel alone, or operate at full load with the diesel fuel as a pilot for the methanol. An additional constraint was that the nozzle design was to be easily adaptable to the existing injection nozzle so that engine head modifications are not required. The initial design was evaluated in a constant volume test chamber in which the pressure was varied from atmospheric to engine compression pressures.

Condensation of fuel vapor on the cold surfaces within the combustion chamber is investigated as a possible mechanism for increased HC emissions from SI engines during cold start. A one-dimensional, transient, mass diffusion analysis is used to examine the condensation of single-species fuels on the surfaces of the combustion chamber as the pressure within the cylinder rises during compression and combustion, and re-vaporization during expansion, blowdown, and exhaust. The effects of wall temperature, fuel volatility, and engine load and speed on this mechanism are also discussed. This analysis shows that low-volatility fuel components can condense on the surfaces of the combustion chamber when the surface temperatures are sufficiently low. This condensed fuel may re-vaporize during the power and exhaust strokes, or it may remain in the combustion chamber until surface temperatures rise, perhaps tens of seconds later.

This paper presents the results of an experimental investigation of the fuel-air mixing process in a port-fuel-injected, 4-valve, spark-ignited engine that was motored to simulate cold cranking and start-up conditions. An infrared fiber-optic instrumented spark plug probe was used to measure the local, crank angle resolved, fuel concentration in the vicinity of the spark gap of a single-cylinder research engine with a production head and fuel injector. The crank-angle resolved fuel concentrations were compared for various injection timings including open-intake-valve (OIV) and closed-intake-valve (CIV) injection, using federal certification gasoline. In addition, the effects of speed, intake manifold pressure, and injected fuel mass were examined.

Methods to reduce direct injected diesel engine emissions in the combustion chamber will be discussed in this paper. The following NOx emission reduction technologies will be reviewed: charge air chilling, water injection, and exhaust gas recirculation (EGR). Emphasis will be placed on the development of an EGR system and the effect of EGR on NOx and particulates. The lower limit of NOx that can be obtained using conventional diesel engine combustion will be discussed. Further reductions in NOx may require changing the combustion process from a diffusion flame to a homogeneous charge combustion system.

A liquid-phase port injection system for liquefied petroleum gas (LPG) generally consists of a fuel storage tank with extended capability of operating up to 600 psi, a fuel pump, and suitable fuel lines to and from the LPG fuel injectors mounted in the fuel rail manifold. Port injection of LPG in the liquid phase is attractive due to engine emissions and performance benefits. However, maintaining the LPG in the liquid phase at under-hood conditions and re-starting after hot soak can be difficult. Multiphase behavior within a liquid-phase LPG injection system was investigated computationally and experimentally. A commercial chemical equilibrium code (ASPEN PLUS™) was used to model various LPG compositions under operating conditions.

During the 1980's, vegetable oils, microemulsions containing fatty alcohols as surfactants, and fatty esters have been extensively investigaed as alternative fuels to #2 diesel fuel (DF-2) used in farm tractors. Despite the importance of vegetable oils (mainly triglycerides) and fatty derivatives to the alternative fuel program, cetane numbers for pure triglycerides and many fatty derivatives were not reported. In the current study, estimated cetane numbers of these materials have been determined by use of a constant volume combustion bomb. Prior research has shown that this equipment can produce cetane numbers that correlate satisfactorily with engine cetane numbers as determied by ASTM D 613. The influence of chemical structure on ignition delay and cetane number was investigated. Evidence is presented that shows the current cetane number scale is not always suitable for these fatty materials. Suggestions are made as to what might be done to remedy this problem.

A technique was developed for measuring the Laminar Burning Velocity (LBV) of multi-component fuel blends for use in high-performance spark-ignition engines. This technique involves the use of a centrally-ignited spherical combustion chamber, and a complementary analysis code. The technique was validated by examining several single-component fuels, and the computational procedure was extended to handle multi-component fuels without requiring detailed knowledge of their chemical composition. Experiments performed on an instrumented high-speed engine showed good agreement between the observed heat-release rates of the fuels and their predicted ranking based on the measured LBV parameters.

A technology path has been identified for development of a high efficiency, durable, gasoline engine, targeted at achieving performance and emissions levels necessary to meet heavy-duty, on-road standards of the foreseeable future. Initial experimental and numerical results for the proposed technology concept are presented. This work summarizes internal research efforts conducted at Southwest Research Institute. An alternative combustion system has been numerically and experimentally examined. The engine utilizes gasoline as the fuel, with a combination of enabling technologies to provide high efficiency operation at ultra-low emissions levels. The concept is based upon very highly-dilute combustion of gasoline at high compression ratio and boost levels. Results from the experimental program have demonstrated engine-out NOx emissions of 0.06 g/hp/hr, at single-cylinder brake thermal efficiencies (BTE) above thirty-four percent.

A new combustion concept has been developed and tested for improving the low to moderate load efficiency and NOx emissions of natural gas engines. This concept involves operation of a dual-fuel natural gas engine on Homogeneous Charge Compression Ignition (HCCI) in the load regime of idle up to 35 % of the peak torque. A dual-fuel approach is used to control the combustion phasing of the engine during HCCI operation, and conventional spark-ignited natural gas combustion is used for the high-load regime. This concept has resulted in an engine with power output and high-load fuel efficiency that are unchanged from the base engine, but with a 10 - 15 % improvement to the low to moderate load fuel efficiency. In addition, the engine-out NOx emissions during HCCI operation are over 90% lower than on spark-ignited natural gas operation over the equivalent load range.

The engine-out emissions and fuel consumption rates for a modern, heavy-duty diesel engine were compared when fueling with a conventional diesel fuel and three water-blend-fuel emulsions. Four different fuels were studied: (1) a conventional diesel fuel, (2) PuriNOx,™ a water-fuel emulsion using the same conventional diesel fuel, but having 20% water by mass, and (3,4) two other formulations of the PuriNOx™ fuel that contained proprietary chemical additives intended to improve combustion efficiency and emissions characteristics. The emissions data were acquired with three different injection-timing strategies using the AVL 8-Mode steady-state test method in a Caterpillar 3176 engine, which had a calibration that met the 1998 nitrogen oxides (NOX) emissions standard.

Significant reductions of particulate matter (PM) and nitrogen oxides (NOx) emissions from diesel engines have been realized through fueling with water-fuel emulsions. However, the physical and chemical in-cylinder mechanisms that affect these pollutant reductions are not well understood. To address this issue, laser-based and chemiluminescence imaging experiments were performed in an optically-accessible, heavy-duty diesel engine using both a standard diesel fuel (D2) and an emulsion of 20% water, by mass (W20). A laser-based Mie-scatter diagnostic was used to measure the liquid-phase fuel penetration and showed 40-70% greater maximum liquid lengths with W20 at the operating conditions tested. At some conditions with low charge temperature or density, the liquid phase fuel may impinge directly on in-cylinder surfaces, leading to increased PM, HC, and CO emissions because of poor mixing.

The impingement of liquid fuel onto the surfaces of the combustion chamber (wall-wetting) has been shown to be an important source of HC emissions from direct-injected SI engines, and can even result in pool fires and diffusion flames. Some degree of wall wetting, particularly on the piston top, is believed to occur in every current DIG engine design, but the behavior of the wall-bound fuel throughout the engine cycle is poorly understood. The goal of this study was to gain a better understanding of the fundamental interaction between liquid fuel droplets and the piston under engine-like conditions, by observing the vaporization of individual fuel drops as the surface temperature and ambient pressures were varied in a controlled environment. The vaporization of several single-component fuels, binary mixtures, and multi-component fuels was examined in the range of surface temperatures between 50 and 300 °C and ambient pressures between 50 and 1270 kPa (abs).

An experimental investigation of the effects of partial premixed charge compression ignition (PCCI) combustion and EGR temperature was conducted on a Caterpillar C-12 heavy-duty diesel engine (HDDE). The addition of EGR and PCCI combustion resulted in significant NOx reductions over the AVL 8-mode test. The lowest weighted BSNOx achieved was 2.55 g/kW-hr (1.90 g/hp-hr) using cooled EGR and 20% port fuel injection (PFI). This represents a 54% reduction compared to the stock engine. BSHC and BSCO emissions increased by a factor of 8 and 10, respectively, compared to the stock engine. BSFC also increased by 7.7%. In general, BSHC, BSCO, BSPM, and BSFC increased linearly with the amount of port-injected fuel.

Researchers at Southwest Research Institute (SwRI) have been working for the past several years on the fundamental and practical aspects of homogeneous charge compression ignition (HCCI) operation of reciprocating engines. Much of the work has focused on the use of diesel fuel. The work at SwRI has, however, demonstrated that there are fundamental limitations on the use of current diesel fuels in HCCI engines. The results of engine and constant volume combustion bomb experiments are presented and discussed. The engine experiments were used to identify important fuel properties that must be included in a fuel specification for HCCI fuels. The primary properties relate to the distillation characteristics and the ignition characteristics. The engine test provided preliminary guidance on the distillation requirements and an indication of the important ignition requirements.

In-cylinder control of particulate emissions in a diesel engine depends on careful control and understanding of the fuel injection and air/fuel mixing process. It is extremely difficult to measure physical parameters of the injection and mixing process in an operating engine, but it is possible to simulate some diesel combustion chamber conditions in a steady flow configuration whose characteristics can be more easily probed. This program created a steady flow environment in which air-flow and injection sprays were characterized under non-combusting conditions, and emissions measurements were made under combusting conditions. A limited test matrix was completed in which the following observations were made. Grid-generated air turbulence decreased particulates, CO, and unburned hydrocarbons, while CO2 and NOx levels were increased. The turbulence accelerated combustion, resulting in more complete combustion and higher temperatures at the measurement location.

Vegetable oils are candidates for alternative fuels in diesel engines. These oils, such as soybean, sunflower, rapeseed, cottonseed, and peanut, consist of various triglycerides. The chemistry of the degradation of vegetable oils when used as alternate diesel fuels thus corresponds to that of triglycerides. To study the chemistry occurring during the precombustion phase of a vegetable oil injected into a diesel engine, a reactor simulating a diesel engine was constructed. Pure triglycerides were injected into the reactor in order to determine differences in the precombustion behavior of the various triglycerides. The reactor allowed motion pictures to be prepared of the injection event as the important reaction parameters, such as pressure, temperature, and atmosphere were varied. Furthermore, samples of the degradation products of precombusted triglycerides were collected and analyzed (gas chromatography / mass spectrometry).

The mixture preparation process was investigated in a direct-injected, 4-valve, SI engine under motored conditions. The interaction between the high-pressure fuel jet and the intake air-flow was observed. Laser-sheet droplet imaging was used to visualize the in-cylinder droplet distributions, and a single-component LDV system was used to measure in-cylinder velocities. The fuel spray was visualized with the engine motored at 1500 and 750 rpm, and with the engine stopped. It was observed that the shape of the fuel spray was distorted by the in-cylinder air motion generated by the intake air flow, and that this effect became more pronounced with increasing engine speed. Velocity measurements were made at five locations on the symmetry plane of the cylinder, with the engine motored at 750 rpm. Comparison of these measurements with, and without, injection revealed that the in-cylinder charge motion was significantly altered by the injection event.

This paper explores the possibility of on-board fuel classification for fuel property adaptive compression-ignition engine control system. The fuel classifier is designed to on-board classify the fuel that a diesel engine is running, including alternative and renewable fuels such as bio-diesel. Based on this classification, the key fuel properties are provided to the engine control system for optimal control of in-cylinder combustion and exhaust treatment system management with respect to the fuel. The fuel classifier employs engine input-output response characteristics measured from standard engine sensors to classify the fuel. For proof-of-concept purposes, engine input-output responses were measured for three different fuels at three different engine operating conditions. Two neural-network-based fuel classifiers were developed for different classification scenarios. Of the three engine operating conditions tested, two conditions were selected for the fuel classifier to be active.

Four broad boiling range materials, representative of current and future feedstocks for diesel fuel, were processed to two levels of sulfur and aromatic content. These materials were then distilled into six to eight fractions each. The resulting 63 fuels were then characterized physically and chemically, and tested in both a constant volume combustion apparatus and a single cylinder diesel engine. The data obtained from these analyses and tests have been analyzed graphically and statistically. The results of the initial statistical analysis, reported here, indicate that the ignition quality of a fuel is dependent not only on the overall aromatic content, but also on the composition of the material formed during hydroprocessing of the aromatics. The NOx emissions, however, are related mainly to the aromatic content of the fuel, and the structure of the aromatic material.

Four different vegetable oils, degummed soybean, once refined cottonseed, peanut and sunflower oils, were injected into a high-pressure, high-temperature environment of nitrogen. The environment was controlled to resemble, thermodynamically, conditions present in a diesel engine at the time of fuel injection. Samples were removed from the sprays of these oils while they were being injected. A sonic, water-cooled probe and a cold trap were used to collect the samples. Chemical analyses of the samples indicated that significant chemical changes occur in the oils during the injection process. The major change is the formation of low-molecular weight compounds from the C18:2 and C18:3 fatty acids.