Search Results

Standard

Heavy Truck and Bus Retarder Downhill Performance Mapping Procedure

2000-05-01

CURRENT

J1489_200005

The procedure covers the estimation of the total retardation capability available to a specific vehicle from: a Natural retardation (rolling resistance, aerodynamic drag, etc). b Engine drag c Engine, integral automatic transmission, driveline or trailer-axle retarders It assumes that foundation brakes are not used for maintaining speed on long mountain descents. Retardation is rated in terms of the maximum grades on which stable control speeds can be maintained for each gear over the range of highway speeds appropriate to that gear. For each gear, the calculation procedure determines maximum grades for at least four values of control speed ranging from the vehicle velocity corresponding to full load governed engine rpm, to the vehicle velocity corresponding to the engine rpm at minimum (idle) speed. In addition, the calculation procedure provides information on the total retarding power available for each gear.

Standard

Clutch Application Powertrain Startability Rating Requirements for Truck and Bus Applications

2004-08-25

HISTORICAL

J2469_200408

Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).

Standard

Clutch Application Powertrain Startability Rating Requirements for Truck and Bus Applications

2017-09-19

CURRENT

J2469_201709

Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).

Standard

Clutch Dimensions for Truck and Bus Applications

2017-08-14

CURRENT

J1806_201708

Although not limited to, these clutches are normally used on trucks considered as Medium-Duty (Class 6 and 7), as well as Heavy-Duty (Class 8).

Standard

Clutch Dimensions for Truck and Bus Applications

1999-11-30

HISTORICAL

J1806_199911

Although not limited to, these clutches are normally used on trucks considered as Medium-Duty (Class 6 and 7), as well as Heavy-Duty (Class 8).

Standard

Clutch Installation and Release Linkage Requirements for Truck and Bus Application

2017-11-03

CURRENT

J2407_201711

Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).

Standard

Clutch Installation and Release Linkage Requirements for Truck and Bus Application

1997-10-01

HISTORICAL

J2407_199710

Although not limited to, these installations are normally used on trucks considered as Medium Duty (Class 6 and 7), as well as Heavy Duty (Class 8).

Standard

Drain and Fill Plug for use on Engines, Transmissions, and Axles

2003-07-29

HISTORICAL

J2606_200307

Drain and Fill plugs used on engines, transmissions, transfer cases and front and rear drive axles for class 5 – 8 vehicles.

Standard

Drain and Fill Plug for use on Engines, Transmissions, and Axles

2017-09-19

CURRENT

J2606_201709

Drain and Fill plugs used on engines, transmissions, transfer cases and front and rear drive axles for class 5 – 8 vehicles.

Standard

Test Method to Obtain Lug-Up Torque Data for Heavy-Duty Truck and Bus Engines

2001-04-25

CURRENT

J2548_200104

This SAE Recommended Practice applies to all forms of diesel and natural gas engines fueled by the combination of diesel fuel and natural gas.

Standard

Torque Ratings for Power Take-off Mounting Pads

2017-09-19

CURRENT

J2662_201709

This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.

Standard

Torque Ratings for Power Take-off Mounting Pads

2003-07-25

HISTORICAL

J2662_200307

This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.

Standard

Pilot Bearings for Truck and Bus Applications

2017-08-14

CURRENT

J1731_201708

This SAE Recommended Practice describes STANDARD-DUTY and EXTREME-DUTY Pilot Bearing requirements and sizes for class 6, 7, and 8 on-highway trucks and buses that use diesel engines and manual transmissions. The recommendations may apply to a wide range of other pilot-bearing applications, such as agricultural, industrial, and construction equipment.

Standard

Pilot Bearings for Truck and Bus Applications

2001-06-12

HISTORICAL

J1731_200106

This SAE Recommended Practice describes STANDARD-DUTY and EXTREME-DUTY Pilot Bearing requirements and sizes for class 6, 7, and 8 on-highway trucks and buses that use diesel engines and manual transmissions. The recommendations may apply to a wide range of other pilot-bearing applications, such as agricultural, industrial, and construction equipment.

Standard

Openings for Six- and Eight-Bolt Truck Transmission Mounted Power Take-Offs

2017-11-03

CURRENT

J704_201711

The accompanying mounting and gear locations are applicable for all general installations of power take-off on the transmission gear box of motor trucks and tractors where the size of the transmission permits. The heavy-duty type opening can be adapted to the regular-duty type by the use of an adapter with 6.35 mm (0.25 in) flange thickness with appropriate bolt pattern and thread engagement. (See Figures 1 and 2.)

Standard

Openings for Six- and Eight-Bolt Truck Transmission Mounted Power Take-Offs

2000-09-07

HISTORICAL

J704_200009

The accompanying mounting and gear locations are applicable for all general installations of power take-off on the transmission gear box of motor trucks and tractors where the size of the transmission permits. The heavy-duty type opening can be adapted to the regular-duty type by the use of an adapter with 6.35 mm (0.25 in) flange thickness with appropriate bolt pattern and thread engagement. (See Figures 1 and 2.)

Standard

OPENINGS FOR SIX- AND EIGHT-BOLT TRUCK TRANSMISSION MOUNTED POWER TAKE-OFFS

1983-06-01

HISTORICAL

J704_198306

Standard

OPENINGS FOR SIX- AND EIGHT-BOLT TRUCK TRANSMISSION MOUNTED POWER TAKE-OFFS

1978-04-01

HISTORICAL

J704B_197804

Standard

CERTIFICATES OF MAXIMUM NET HORSEPOWER FOR MOTOR TRUCKS AND TRUCK TRACTORS

1965-02-01

HISTORICAL

J690_196502

Standard

SAE Nodal Mount

2017-08-14

CURRENT

J1134_201708

This SAE Recommended Practice establishes a single bolt pattern for the No. 1 clutch housing (see Figure 1) and the No. 2 clutch housing (see Figure 2). These four bolt patterns are designated to give commonality of mounting brackets in existing frame rails. The 420 mm (16.5 in) span, pad face to pad face, allows the ease of installation in existing frame rail widths. This is also the minimum spacing which will accommodate commonly used clutches.