Search Results

As the number of Hydraulic Hybrid Powertrain equipped motor vehicles has increased, the number of terms, abbreviations, and acronyms which describe various components of these systems has increased. For the sake of industry standardization and to bring some order to the proliferation of such terms, abbreviations, and acronyms, the SAE Truck and Bus Hydraulic Hybrid committee prepared this document.

This SAE Standard describes the terms or names of the parts, characteristics, and parameters of automotive pull-type clutches used in trucks, and of vehicle apparatus or components related to the pull-type clutch.

This SAE Recommended Practice has been adopted by SAE to specify: a A basis for net engine retarder power rating b Reference inlet air test conditions c A method for correcting observed engine retarder power to reference conditions d A method for determining net engine retarder power with a dynamometer

This SAE Recommended Practice has been adopted by SAE to specify: a A basis for net engine retarder power rating b Reference inlet air test conditions c A method for correcting observed engine retarder power to reference conditions d A method for determining net engine retarder power with a dynamometer

This SAE Recommended Practice applies to Liquefied Natural Gas Vehicle Fuel. The purpose of this document is to provide information on issues that are important to consider regarding LNG metering and dispensing systems.

This SAE Recommended Practice applies to Liquefied Natural Gas Vehicle Fuel. The purpose of this document is to provide information on issues that are important to consider regarding LNG metering and dispensing systems.

This SAE Recommended Practice applies to Liquefied Natural Gas Vehicle Fuel. The purpose of this document is to provide information on issues that are important to consider regarding LNG metering and dispensing systems.

The accessory components covered by this information report include: air brake compressors, alternators, air conditioning compressors, engine cooling fans and drives, and power steering pumps. The values show an estimate of the average power requirements of known duty cycles of these engine drive accessories.

This report is intended to provide the information to estimate the accessory load of a typical heavy truck or bus. The components covered include: air compressors, alternators, refrigerant compressors, engine cooling fans and power steering pumps. The values show an estimate of the average power requirements and duty cycles for these accessories. This report does not address loads required for engine operation. Required systems include those needed for engine performance such as fuel pumps and electronic control modules (ECM).

This SAE Recommended Practice takes into account modern standardized methods for collecting and summarizing data that has an effect on vehicle steady-state performance, such as engine output (gross and net), transmission losses, drivetrain efficiency, vehicle aerodynamic devices for various vehicle and body configurations, as well as road surface variations and air density variations resulting from altitude and barometric effects. The procedure does not address vehicle transient performance (acceleration, braking, and cornering), because of the considerable amount of additional data required such as moment of inertia of all the rotating parts. Nor does it address vehicles with torque converters and automatic transmissions. This document is, therefore, intended for vehicles having fixed-ratio type transmissions and positive engagement clutches. Metric and ISO unit conversions are provided in the metric conversion tables at the end of this procedure (see Appendix B).

This SAE Recommended Practice takes into account modern standardized methods for collecting and summarizing data that has an effect on vehicle steady-state performance, such as engine output, gross and net, transmission losses, drivetrain efficiency, vehicle air drag reduction devices for various vehicle and body configurations, as well as road surface variations and air density variations resulting from altitude and barometric effects. The procedure does not address vehicle transient performance (acceleration, braking, and cornering), because of the considerable amount of additional data required such as moment of inertia of all the rotating parts. Nor does it address vehicles with torque converters and automatic transmissions. This document is therefore intended for vehicles having fixed ratio type transmissions and positive engagement clutches, used on the USA road system.

This SAE Standard describes a procedure to be used to evaluate a disturbance known as “idle gear rattle” which can exist in vehicles equipped with manual transmissions and clutches. Other types of noises associated with operation at idle are also briefly described.

This SAE Standard describes a procedure to be used to evaluate a disturbance known as “idle gear rattle” which can exist in vehicles equipped with manual transmissions and clutches. Other types of noises associated with operation at idle are also briefly described.

This SAE Recommended Practice applies to vehicle exhaust smoke measurements made using the Snap-Acceleration test procedure. Because this is a non-moving vehicle test, this test can be conducted along the roadside, in a truck depot, a vehicle repair facility, or other test facilities. The test is intended to be used on heavy-duty trucks and buses powered by diesel engines. It is designed to be used in conjunction with smokemeters using the light extinction principle of smoke measurement. This procedure describes how the snap-acceleration test is to be performed. It also gives specifications for the smokemeter and other test instrumentation and describes the algorithm for the measurement and quantification of the exhaust smoke produced during the test. Included are discussions of factors which influence snap-acceleration test results and methods to correct for these conditions.

This SAE Recommended Practice applies to vehicle exhaust smoke measurements made using the Snap-Acceleration test procedure. Because this is a non-moving vehicle test, this test can be conducted along the roadside, in a truck depot, a vehicle repair facility, or other test facilities. The test is intended to be used on heavy-duty trucks and buses powered by diesel engines. It is designed to be used in conjunction with smokemeters using the light extinction principle of smoke measurement. This procedure describes how the snap-acceleration test is to be performed. It also gives specifications for the smokemeter and other test instrumentation and describes the algorithm for the measurement and quantification of the exhaust smoke produced during the test. Included are discussions of factors which influence snap-acceleration test results and methods to correct for these conditions.

This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for “free-spooling” may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control “free-spooling,” but will not be relied on to control or hold a load.

This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for “free-spooling” may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control “free-spooling,” but will not be relied on to control or hold a load.

This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for “free-spooling” may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control “free-spooling,” but will not be relied on to control or hold a load.

This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for “free-spooling” may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control “free-spooling,” but will not be relied on to control or hold a load.

This SAE Standard applies only to new winches which are primarily designed for intermittent pulls and lifts and whose configuration and condition are the same as when they were shipped by the manufacturer. They are not intended to be used in any manner for the movement of personnel. They may be driven by any power source recommended by the manufacturer and will be capable of being powered in either direction. They will be equipped with an automatic safety brake system to control a load when lowering under power and positively hold a load when power is not being delivered to the winch. A hydraulic flow control valve or similar device may be used in the brake system to control a load when lowering under power. A clutch to release the drum for "free-spooling" may be provided and will be designed not to disengage itself under load. A drag brake may be provided to control "free-spooling," but will not be relied on to control or hold a load.