Refine Your Search

Topic

Search Results

Standard

A Tilt Table Procedure for Measuring the Static Rollover Threshold for Heavy Trucks

2011-05-17
CURRENT
J2180_201105
The test procedure applies to roll coupled units such as straight trucks, tractor semitrailers, full trailers, B-trains, etc. The test is aimed at evaluating the level of lateral acceleration required to rollover a vehicle or a roll-coupled unit of a vehicle in a steady turning situation. Transient, vibratory, or dynamic rollover situations are not simulated by this test. Furthermore, the accuracy of the test decreases as the tilt angle increases, although this is a small effect at the levels of tilt angle used in testing heavy trucks. The test accuracy is accepted for vehicles that will rollover at lateral acceleration levels below 0.5 g corresponding to a tilt table angle of less than approximately 27 degrees. Even so, the results for heavy trucks with rollover thresholds greater than 0.5 g could be used for comparing their relative static roll stability.
Standard

Truck Tractor Semitrailer Interchange Coupling Dimensions

2017-08-09
CURRENT
J701_201708
The information in this SAE Information Report is the result of studies by the Automobile Manufacturers Association, American Trucking Association, and Truck Trailer Manufacturers Association, to achieve interchangeability of equipment which will comply with the legal dimensional limitations for the majority of states and yet permit increased loading space within these dimensions. This in no way supersedes other information in the SAE Handbook on this subject. Some cases will require more care in application allowing splash shield clearance at trailer support interference points and positioning fifth wheel to allow trailer swing clearance on an 11% grade. All dimensions are given in inches. Table 1 and Figures 1 and 2 show basic requirements for interchangeability of truck tractor and semitrailer equipment. Figure 3 shows the interchangeability of the doubles converter dolly.
Standard

Truck Tractor Semitrailer Interchange Coupling Dimensions

1984-08-01
HISTORICAL
J701_198408
The information in this SAE Information Report is the result of studies by Automobile Manufacturers Association, American Trucking Association, and Truck Trailer Manufacturers Association, to achieve interchangeability of equipment which will comply with the legal dimension limitation for the majority of states and yet permit increased loading space within these dimensions. This in no way supersedes other information in the SAE Handbook on this subject. It will, in some cases, require more care in application
Standard

Truck Tractor Semitrailer Interchange Coupling Dimensions

2014-01-03
HISTORICAL
J701_201401
The information in this SAE Information Report is the result of studies by the Automobile Manufacturers Association, American Trucking Association, and Truck Trailer Manufacturers Association, to achieve interchangeability of equipment which will comply with the legal dimensional limitations for the majority of states and yet permit increased loading space within these dimensions. This in no way supersedes other information in the SAE Handbook on this subject. Some cases will require more care in application allowing splash shield clearance at trailer support interference points and positioning fifth wheel to allow trailer swing clearance on an 11% grade. All dimensions are given in inches. Table 1 and Figures 1 and 2 show basic requirements for interchangeability of truck tractor and semitrailer equipment. Figure 3 shows the interchangeability of the doubles converter dolly.
Standard

Truck Tractor Semitrailer Interchange Coupling Dimensions

1968-07-01
HISTORICAL
J701A_196807
The information in this SAE Information Report is the result of studies by Automobile Manufacturers Association, American Trucking Association, and Truck Trailer Manufacturers Association, to achieve interchangeability of equipment which will comply with the legal dimension limitation for the majority of states and yet permit increased loading space within these dimensions. This in no way supersedes other information in the SAE Handbook on this subject. It will, in some cases, require more care in application
Standard

Truck Overall Widths Across Dual Tires

1989-04-01
HISTORICAL
J693_198904
To aid in obtaining overall widths across dual tires when requirements of frame widths, spring widths, chain clearance, and standard rim sizes are considered.
Standard

Motor Truck CA Dimensions

2011-06-13
CURRENT
J691_201106
This SAE Recommended Practice sets forth recommended back of cab to rear axle (CA) dimensional data. It applies to 4- and 6-wheel motor trucks but not necessarily to truck-tractors.
Standard

Motor Truck CA Dimensions

1990-09-01
HISTORICAL
J691_199009
This SAE Recommended Practice sets forth recommended back of cab to rear axle (CA) dimensional data. It applies to 4- and 6-wheel motor trucks but not necessarily to truck-tractors.
Standard

Truck Overall Widths Across Dual Tires

1984-06-01
HISTORICAL
J693_198406
To aid in obtaining overall widths across dual tires when requirements of frame widths, spring widths, chain clearance, and standard rim sizes are considered.
Standard

Motor Truck CA Dimensions

1984-06-01
HISTORICAL
J691_198406
This SAE Recommended Practice sets forth recommended back of cab to rear axle (CA) dimensional data. It applies to 4- and 6-wheel motor trucks but not necessarily to truck-tractors.
Standard

Exterior Sound Level for Heavy Trucks and Buses

1969-07-01
HISTORICAL
J366_196907
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
Standard

Exterior Sound Level for Heavy Trucks and Buses

2001-04-27
HISTORICAL
J366_200104
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
Standard

Exterior Sound Level for Heavy Trucks and Buses

2011-09-12
CURRENT
J366_201109
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
Standard

Exterior Sound Level for Heavy Trucks and Buses

1984-11-01
HISTORICAL
J366_198411
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
Standard

Exterior Sound Level for Heavy Trucks and Buses

1977-08-01
HISTORICAL
J366B_197708
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
Standard

Exterior Sound Level for Heavy Trucks and Buses

1978-07-01
HISTORICAL
J366B_197807
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
Standard

Exterior Sound Level for Heavy Trucks and Buses

1971-06-01
HISTORICAL
J366A_197106
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
Standard

Exterior Sound Level for Heavy Trucks and Buses

1973-04-01
HISTORICAL
J366B_197304
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the maximum exterior sound level for highway motor trucks, truck tractors, and buses. The test results obtained by this test procedure give an objective measure of the maximum noise level emitted by vehicles under a prescribed condition. A subjective rating of the annoyance caused by vehicles in use may not be directly related to this type of noise level measurement.
X