Search Results

Standard

Identification of Truck, Trailer, and Bus Wheel Seals and Associated Packaging

2008-07-17

HISTORICAL

J2224_200807

This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging.

Standard

Identification of Truck, Trailer, and Bus Wheel Seals and Associated Packaging

2015-11-19

CURRENT

J2224_201511

This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging. 1.1 Purpose The purpose of this document is to provide users of truck, trailer, and bus wheel seals a means of identifying the suppliers of all such components by use of the symbology utilized by the suppliers on their components and packaging.

Standard

Identification of Truck, Trailer, and Bus Wheel Seals and Associated Packaging

2002-05-31

HISTORICAL

J2224_200205

This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging.

Standard

IDENTIFICATION OF TRUCK, TRAILER, AND BUS WHEEL SEALS AND ASSOCIATED PACKAGING

1994-10-01

HISTORICAL

J2224_199410

This SAE Information Report lists the symbols used by suppliers of truck, trailer, and bus wheel seals to identify their products. These symbols appear on seals and packaging.

Standard

Setting Preload in Heavy-Duty Wheel Bearings

2019-10-07

CURRENT

J2535_201910

This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.

Standard

Setting Preload in Heavy-Duty Wheel Bearings

2013-02-11

HISTORICAL

J2535_201302

This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.

Standard

Setting Preload in Heavy-Duty Wheel Bearings

2001-03-01

HISTORICAL

J2535_200103

This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway, disc wheel / outboard drum brake applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.

Standard

Setting Preload in Heavy-Duty Wheel Bearings

2006-12-06

HISTORICAL

J2535_200612

This SAE Recommended Practice applies to the four primary, large volume applications in the class 7-8 heavy-duty market place, as specified in SAE J1842: a “N” trailer axle b “R” powered rear axle c “FF / FG” nonpowered front axle d “P” trailer axle This document applies to on-highway, disc wheel / outboard drum brake applications. It is not applicable to those applications that exceed the GAWR ratings or the load line restrictions listed in columns “A,” “B,” and “C” of Table 1. Load lines are measured from the inboard bearing cup backface as shown in 3.4. This document establishes preload force values only. The methodology to obtain these force values must be determined by the fastener supplier and/or axle assembler. This document reviews the bearing system. It is NOT intended to prescribe (new or existing) axle and/or hub manufacturers’ ratings and/or specifications.

Standard

DISC WHEEL/HUB OR DRUM INTERFACE DIMENSIONS—COMMERCIAL VEHICLES

1997-07-01

HISTORICAL

J694_199707

This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document.

Standard

DISC WHEEL/HUB OR DRUM INTERFACE DIMENSIONS - COMMERCIAL VEHICLES

1988-09-01

HISTORICAL

J694_198809

This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multi-purpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this recommended practice.

Standard

Disc Wheel/Hub or Drum Interface Dimensions—Commercial Vehicles

1998-08-01

HISTORICAL

J694_199808

This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document.

Standard

Disc Wheel/Hub or Drum Interface Dimensions—Commercial Vehicles

2001-02-22

HISTORICAL

J694_200102

This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multipurpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this document.

Standard

DISC WHEEL/HUB OR DRUM INTERFACE DIMENSIONS - COMMERCIAL VEHICLES

1988-05-01

HISTORICAL

J694_198805

This SAE Recommended Practice contains dimensions and their tolerances concerning disc wheel to hub or drum interface areas for commercial vehicles and multi-purpose passenger vehicles. Stamped disc wheels for single applications and special or less common applications are not covered in this recommended practice.

Standard

Nomenclature - Wheels, Hubs, and Rims for Commercial Vehicles

2017-10-23

HISTORICAL

J393_201710

This SAE Recommended Practice establishes uniform engineering nomenclature for wheels, hubs, rims, and their components used in truck, bus, and trailer applications. This nomenclature and accompanying drawings are intended to define functional truck wheel, hub, and rim designs. For nomenclature specific to “passenger-type” disc wheels, refer to SAE J1982. The International Standard (ISO) nomenclature is shown in parentheses when different than SAE J393.

Standard

Nomenclature - Wheels, Hubs, and Rims for Commercial Vehicles

2022-06-20

CURRENT

J393_202206

This SAE Recommended Practice establishes uniform engineering nomenclature for wheels, hubs, rims, and their components used in truck, bus, and trailer applications. This nomenclature and accompanying drawings are intended to define functional truck wheel, hub, and rim designs. For nomenclature specific to “passenger-type” disc wheels, refer to SAE J1982. The International Standard (ISO) nomenclature is shown in parentheses when different than SAE J393.

Standard

Wheel End Assembly and Axle Spindle Interface Dimensions - Truck and Bus

2020-02-13

CURRENT

J2475_202002

This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, spindle threads, bearing cones, bearing spacer, seal, and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W.

Standard

Wheel End Assembly and Axle Spindle Interface Dimensions—Truck and Bus

2005-03-21

HISTORICAL

J2475_200503

This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, R, N and P. SAE configurations FC, K, L, U, and W are not included, but may be added in the future.

Standard

Wheel End Assembly and Axle Spindle Interface Dimensions—Truck and Bus

2008-08-22

HISTORICAL

J2475_200808

This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, U, W, R, N and P.

Standard

Wheel End Assembly and Axle Spindle Interface Dimensions - Truck and Bus

2014-07-30

HISTORICAL

J2475_201407

This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W.

Standard

AXLE END STANDARDIZATION

1994-09-01

HISTORICAL

J1842_199409

This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 7 and 8 truck/truck-tractor nonpowered front axles, powered and nonpowered rear axles, and trailer axles.