Refine Your Search

Search Results

Viewing 1 to 7 of 7
Standard

Selection of Transmission Media

2000-02-23
CURRENT
J2056/3_200002
This SAE Information Report studies the present transmission media axioms and takes a fresh look at the Class C transmission medium requirements and also the possibilities and limitations of using a twisted pair as the transmission medium. The choice of transmission medium is a large determining factor in choosing a Class C scheme.
Standard

Communication Transceivers Qualification Requirements - LIN

2019-07-18
CURRENT
J2962/1_201907
This document covers the requirements for transceiver qualification. Requirements stated in this document will provide a minimum standard level of performance for the LIN transceiver block in the IC to which all compatible transceivers shall be designed. No other features in the IC are tested or qualified as part of this recommended practice. This will assure robust serial data communication among all connected devices regardless of supplier. The goal of SAE J2962-1 is to commonize approval processes of LIN transceivers across OEMs. The intended audience includes, but is not limited to, LIN transceiver suppliers, component release engineers, and vehicle system engineers.
Standard

Single Wire CAN Network for Vehicle Applications

2000-02-14
CURRENT
J2411_200002
This SAE Recommended Practice defines the Physical Layer and portions of the Data Link Layer of the OSI model for data communications. In particular, this document specifies the physical layer requirements for any Carrier Sense Multiple Access/Collision Resolution (CSMA/CR) data link which operates on a single wire medium to communicate among Electronic Control Units (ECU) on road vehicles. Requirements stated in this document will provide a minimum standard level of performance to which all compatible ECUs and media shall be designed. This will assure full serial data communication among all connected devices regardless of supplier. This document is to be referenced by the particular vehicle OEM Component Technical Specification which describes any given ECU in which the single wire data link controller and physical layer interface is located. Primarily, the performance of the physical layer is specified in this document.
Standard

Class B Data Communications Network Interface

2006-06-07
HISTORICAL
J1850_200606
This SAE Standard establishes the requirements for a Class B Data Communication Network Interface applicable to all On- and Off-Road Land-Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers. This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps (see Appendix A for a checklist of application-specific features). The Physical Layer parameters are specified as they would be detected on the network media, not within any particular module or integrated circuit implementation.
Standard

Class B Data Communications Network Interface

2015-10-14
CURRENT
J1850_201510
This SAE Standard establishes the requirements for a Class B Data Communication Network Interface applicable to all On-and OffRoad Land-Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers. This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps (see Appendix A for a checklist of application-specific features). The Physical Layer parameters are specified as they would be detected on the network media, not within any particular module or integrated circuit implementation.
Standard

File Structures for a Node Capability File (NCF)

2010-01-07
CURRENT
J2602/3_201001
This document covers the requirements for SAE implementations based on LIN 2.0. Requirements stated in this document will provide a minimum standard level of performance to which all compatible systems, design and development tools, software, ECUs and media shall be designed. This will assure consistent and unambiguous serial data communication among all connected devices regardless of supplier. This document may be referenced by any vehicle OEM component technical specification that describes any given ECU in which the single wire data link controller and physical layer interface is located. The intended audience includes, but is not limited to, ECU suppliers, LIN controller suppliers, LIN transceiver suppliers, component release engineers and vehicle system engineers.
Standard

LIN Network for Vehicle Applications Conformance Test

2012-11-19
CURRENT
J2602/2_201211
This document covers the tests to be performed on all SAE J2602-1 defined Master and Slave nodes. Tests described in this document will ensure a minimum standard level of performance to which all compatible Electronic Control Unit (ECUs) and media shall be designed. This will assure full serial data communication among all connected devices regardless of supplier. The goal of SAE J2602-2 is to improve the interoperability and interchangeability of LIN devices within a network by verifying the devices pass a minimum set of tests. To allow for easy cross-reference, this document is arranged such that the conformance test for a given section in SAE J2602-1 is in the same section in SAE J2602-2. This document is to be referenced by the particular vehicle Original Equipment Manufacturer (OEM) component technical specification that describes any given ECU in which the LIN data link controller and physical layer interface is located.
X