Refine Your Search

Date

Date

Topic

Topic

Electrical systems High voltage systems Connectors and terminals Analysis methodologies Identification Vehicle Architecture For Data Communications Standards

Search Results

Viewing 1 to 20 of 36
12Next >Last >>
Sort by published
Standard

Glossary of Vehicle Networks for Multiplexing and Data Communications
1997-09-01
CURRENT
J1213/1_199709
This document covers the general terms and corresponding definitions that support the design, development, implementation, testing, and application of vehicle networks. The terminology also covers some terms and concepts of distributed embedded systems, network hardware, network software, physical layers, protocols, and other related areas.
Standard

GLOSSARY OF AUTOMOTIVE ELECTRONIC TERMS
1982-11-01
HISTORICAL
J1213_198211
This Glossary confines its content to the specific field of electronic systems and subsystems as they pertain to the automotive engineer.
Standard

GLOSSARY OF RELIABILITY TERMINOLOGY ASSOCIATED WITH AUTOMOTIVE ELECTRONICS
1988-10-01
HISTORICAL
J1213B_198810
This compilation of terms, acronyms and symbols was drawn from usage which should be familiar to those working in automotive electronics reliability. Terms are included which are used to describe how items, materials and systems are evaluated for reliability, how they fail, how failures are modeled and how failures are prevented. Terms are also included from the disciplines of designing for reliability, testing and failure analysis as well as the general disciplines of Quality and Reliability Engineering. This glossary is intended to augment SAE J1213, Glossary of Automotive Electronic Terms.
Standard

TOKEN SLOT NETWORK FOR AUTOMOTIVE CONTROL
1996-10-01
HISTORICAL
J2106_199610
The Token Slot Data Link is intended to provide periodic, broadcast communications (communication that must occur on a regular, predetermined basis) within a vehicle system. The Token Slot protocol achieves this by implementing a masterless, deterministic, non-contention Token Slot sequence which is designed to offer a transmit token to all devices (or nodes) without requiring that they respond. After acquiring the token, messages may be sent and verified using a variety of built-in techniques. The token passing slot sequence is then reinitiated by the current token holder.
Standard

TOKEN SLOT NETWORK FOR AUTOMOTIVE CONTROL
1991-04-29
HISTORICAL
J2106_199104
The Token Slot Data Link is intended to provide periodic, broadcast communications (communication that must occur on a regular, predetermined basis) within a vehicle system. The Token Slot protocol achieves this by implementing a masterless, deterministic, non-contention Token Slot sequence which is designed to offer a transmit token to all devices (or nodes) without requiring that they respond. After acquiring the token, messages may be sent and verified using a variety of built-in techniques. The token passing slot sequence is then reinitiated by the current token holder.
Standard

Class A Multiplexing Actuators
2006-09-12
HISTORICAL
J2057/2_200609
The Class A Task Force of the Vehicle Network for Multiplex and Data Communications Committee is publishing this SAE Information Report to provide insight into Class A Multiplexing. Multiplexed actuators are generally defined as devices which accept information from the multiplexed bus. A multiplexed actuator can be an output device controlled by the operator or an intelligent controller. A Multiplex actuator can also be a display device that reports the status of a monitored vehicle function. This document is intended to help the network system engineers and is meant to stimulate the design thought process. A list of multiplexed actuator examples is provided in Appendix A, Figure A1. Many other examples can be it identified.
Standard

Class A Multiplexing Actuators
2022-12-20
CURRENT
J2057/2_202212
The Class A Task Force of the Vehicle Network for Multiplex and Data Communications Committee is publishing this SAE Information Report to provide insight into Class A Multiplexing. Multiplexed actuators are generally defined as devices which accept information from the multiplexed bus. A multiplexed actuator can be an output device controlled by the operator or an intelligent controller. A Multiplex actuator can also be a display device that reports the status of a monitored vehicle function. This document is intended to help the network system engineers and is meant to stimulate the design thought process. A list of multiplexed actuator examples is provided in Appendix A, Figure A1. Many other examples can be it identified.
Standard

Class A Multiplexing Sensors
2022-12-20
CURRENT
J2057/3_202212
The Class A Task Force of the Vehicle Network for Multiplexing and Data Communications Subcommittee is providing information on sensors that could be applicable for a Class A Bus application. Sensors are generally defined as any device that inputs information onto the bus. Sensors can be an input controlled by the operator or an input that provides the feedback or status of a monitored vehicle function. Although there is a list of sensors provided, this list is not all-inclusive. This SAE Information Report is intended to help the network system engineer and is meant to stimulate the design thought process.
Standard

Class A Multiplexing Sensors
2006-09-12
HISTORICAL
J2057/3_200609
The Class A Task Force of the Vehicle Network for Multiplexing and Data Communications Subcommittee is providing information on sensors that could be applicable for a Class A Bus application. Sensors are generally defined as any device that inputs information onto the bus. Sensors can be an input controlled by the operator or an input that provides the feedback or status of a monitored vehicle function. Although there is a list of sensors provided, this list is not all-inclusive. This SAE Information Report is intended to help the network system engineer and is meant to stimulate the design thought process.
Standard

Class B Data Communication Network Messages - Part 3 - Frame IDs for Single-Byte Forms of Headers
2011-05-02
CURRENT
J2178/3_201105
This SAE Recommended Practice defines the information contained in the header and data fields of non-diagnostic messages for automotive serial communications based on SAE J1850 Class B networks. This document describes and specifies the header fields, data fields, field sizes, scaling, representations, and data positions used within messages. The general structure of a SAE J1850 message frame without in-frame response is shown in Figure 1. The structure of a SAE J1850 message with in-frame response is shown in Figure 2. Figures 1 and 2 also show the scope of frame fields defined by this document for non-diagnostic messages. Refer to SAE J1979 for specifications of emissions related diagnostic message header and data fields. Refer to SAE J2190 for the definition of other diagnostic data fields. The description of the network interface hardware, basic protocol definition, electrical specifications, and the CRC byte is given in SAE J1850.
Standard

Selection of Transmission Media
2000-02-23
HISTORICAL
J2056/3_200002
This SAE Information Report studies the present transmission media axioms and takes a fresh look at the Class C transmission medium requirements and also the possibilities and limitations of using a twisted pair as the transmission medium. The choice of transmission medium is a large determining factor in choosing a Class C scheme.
Standard

Selection of Transmission Media
2022-12-20
CURRENT
J2056/3_202212
This SAE Information Report studies the present transmission media axioms and takes a fresh look at the Class C transmission medium requirements and also the possibilities and limitations of using a twisted pair as the transmission medium. The choice of transmission medium is a large determining factor in choosing a Class C scheme.
Standard

Class A Multiplexing Architecture Strategies
2022-12-20
CURRENT
J2057/4_202212
The subject matter contained within this SAE Information Report is set forth by the Class A Task Force of the Vehicle Network for Multiplexing and Data Communications (Multiplex) Committee as information the network system designer should consider. The Task Force realizes that the information contained in this report may be somewhat controversial and a consensus throughout the industry does not exist at this time. The Task Force also intends that the analysis set forth in this document is for sharing information and encouraging debate on the benefits of utilizing a multiple network architecture.
Standard

Class A Multiplexing Architecture Strategies
2006-09-12
HISTORICAL
J2057/4_200609
The subject matter contained within this SAE Information Report is set forth by the Class A Task Force of the Vehicle Network for Multiplexing and Data Communications (Multiplex) Committee as information the network system designer should consider. The Task Force realizes that the information contained in this report may be somewhat controversial and a consensus throughout the industry does not exist at this time. The Task Force also intends that the analysis set forth in this document is for sharing information and encouraging debate on the benefits of utilizing a multiple network architecture.
Standard

Class A Application/Definition
2022-12-20
CURRENT
J2057/1_202212
This SAE Information Report will explain the differences between Class A, B, and C networks and clarify through examples, the differences in applications. Special attention will be given to a listing of functions that could be attached to a Class A communications network.
Standard

Class B Data Communication Network Messages - Detailed Header Formats and Physical Address Assignments
2011-04-01
CURRENT
J2178/1_201104
This SAE Recommended Practice defines the information contained in the header and data fields of non-diagnostic messages for automotive serial communications based on SAE J1850 Class B networks. This document describes and specifies the header fields, data fields, field sizes, scaling, representations, and data positions used within messages. The general structure of a SAE J1850 message frame without in-frame response is shown in Figure 1. The structure of a SAE J1850 message with in-frame response is shown in Figure 2. Figures 1 and 2 also show the scope of frame fields defined by this document for non-diagnostic messages. Refer to SAE J1979 for specifications of emissions related diagnostic message header and data fields. Refer to SAE J2190 for the definition of other diagnostic data fields. The description of the network interface hardware, basic protocol definition, the electrical specifications, and the CRC byte are given in SAE J1850.
Standard

High-Speed CAN (HSC) for Vehicle Applications at 500 kbps with CAN FD Data at 5 Mbps
2022-11-02
CURRENT
J2284/5_202211
This SAE Recommended Practice will define the physical layer and portions of the data link layer of the open systems interconnection model (ISO 7498) for a 500 kbps arbitration bus with CAN FD data at 5 Mbps high-speed CAN (HSC) protocol implementation. Both ECU and media design requirements for networks will be specified. Requirements will primarily address the CAN physical layer implementation. Requirements will focus on a minimum standard level of performance from the High-Speed CAN (HSC) implementation. All ECUs and media shall be designed to meet certain component level requirements in order to ensure the HSC implementation system level performance at 500 kbps arbitration bus with CAN FD Data at 5 Mbps. The minimum performance level shall be specified by system level performance requirements or characteristics described in detail in Section 6 of this document.
Standard

High-Speed CAN (HSC) for Vehicle Applications at 500 kbps with CAN FD Data at 5 Mbps
2016-09-09
HISTORICAL
J2284/5_201609
This SAE Recommended Practice will define the Physical Layer and portions of the Data Link Layer of the Open Systems Interconnection model (ISO 7498) for a 500 kbps arbitration bus with CAN FD Data at 5 Mbps High-Speed CAN (HSC) protocol implementation. Both ECU and media design requirements for networks will be specified. Requirements will primarily address the CAN physical layer implementation. Requirements will focus on a minimum standard level of performance from the High-Speed CAN (HSC) implementation. All ECUs and media shall be designed to meet certain component level requirements in order to ensure the HSC implementation system level performance at 500 kbps arbitration bus with CAN FD Data at 5 Mbps. The minimum performance level shall be specified by system level performance requirements or characteristics described in detail in Section 6 of this document.
12Next >Last >>
X