Refine Your Search

Search Results

Viewing 1 to 15 of 15
Standard

Class A Multiplexing Architecture Strategies

2006-09-12
CURRENT
J2057/4_200609
The subject matter contained within this SAE Information Report is set forth by the Class A Task Force of the Vehicle Network for Multiplexing and Data Communications (Multiplex) Committee as information the network system designer should consider. The Task Force realizes that the information contained in this report may be somewhat controversial and a consensus throughout the industry does not exist at this time. The Task Force also intends that the analysis set forth in this document is for sharing information and encouraging debate on the benefits of utilizing a multiple network architecture.
Standard

Chrysler Sensor and Control (CSC) Bus Multiplexing Network for Class 'A' Applications

2002-07-25
CURRENT
J2058_200207
THE CSC Bus components defined herein were developed to provide simple, yet reliable, communication between a host master module and its sensors and actuators. The scheme chosen provides the ability to communicate in both polling mode and direct addressing modes. Vehicle Architecture for Data Communication Standards Committee voted to cancel document - 7/19/2002 J2058 and J2106 Rationale Per Jack Volk, Vice Chairperson of Vehicle Architecture for Data Communication Standards Committee, document not being used. Information may be contained in other documents, (not necessarily SAE documents).
Standard

Chrysler Sensor and Control (CSC) Bus Multiplexing Network for Class 'A' Applications

1990-06-21
HISTORICAL
J2058_199006
THE CSC Bus components defined herein were developed to provide simple, yet reliable, communication between a host master module and its sensors and actuators. The scheme chosen provides the ability to communicate in both polling mode and direct addressing modes. Vehicle Architecture for Data Communication Standards Committee voted to cancel document - 7/19/2002 J2058 and J2106 Rationale Per Jack Volk, Vice Chairperson of Vehicle Architecture for Data Communication Standards Committee, document not being used. Information may be contained in other documents, (not necessarily SAE documents).
Standard

Class A Multiplexing Sensors

2001-08-30
HISTORICAL
J2057/3_200108
The Class A Task Force of the Vehicle Network for Multiplexing and Data Communications Subcommittee is providing information on sensors that could be applicable for a Class A Bus application. Sensors are generally defined as any device that inputs information onto the bus. Sensors can be an input controlled by the operator or an input that provides the feedback or status of a monitored vehicle function. Although there is a list of sensors provided, this list is not all-inclusive. This SAE Information Report is intended to help the network system engineer and is meant to stimulate the design thought process.
Standard

Class A Application/Definition

2006-09-12
CURRENT
J2057/1_200609
This SAE Information Report will explain the differences between Class A, B, and C networks and clarify through examples, the differences in applications. Special attention will be given to a listing of functions that could be attached to a Class A communications network.
Standard

Single Wire CAN Network for Vehicle Applications

2000-02-14
CURRENT
J2411_200002
This SAE Recommended Practice defines the Physical Layer and portions of the Data Link Layer of the OSI model for data communications. In particular, this document specifies the physical layer requirements for any Carrier Sense Multiple Access/Collision Resolution (CSMA/CR) data link which operates on a single wire medium to communicate among Electronic Control Units (ECU) on road vehicles. Requirements stated in this document will provide a minimum standard level of performance to which all compatible ECUs and media shall be designed. This will assure full serial data communication among all connected devices regardless of supplier. This document is to be referenced by the particular vehicle OEM Component Technical Specification which describes any given ECU in which the single wire data link controller and physical layer interface is located. Primarily, the performance of the physical layer is specified in this document.
Standard

Selection of Transmission Media

2000-02-23
CURRENT
J2056/3_200002
This SAE Information Report studies the present transmission media axioms and takes a fresh look at the Class C transmission medium requirements and also the possibilities and limitations of using a twisted pair as the transmission medium. The choice of transmission medium is a large determining factor in choosing a Class C scheme.
Standard

Glossary of Vehicle Networks for Multiplexing and Data Communications

1997-09-01
CURRENT
J1213/1_199709
This document covers the general terms and corresponding definitions that support the design, development, implementation, testing, and application of vehicle networks. The terminology also covers some terms and concepts of distributed embedded systems, network hardware, network software, physical layers, protocols, and other related areas.
Standard

LIN Network for Vehicle Applications Conformance Test

2012-11-19
CURRENT
J2602/2_201211
This document covers the tests to be performed on all SAE J2602-1 defined Master and Slave nodes. Tests described in this document will ensure a minimum standard level of performance to which all compatible Electronic Control Unit (ECUs) and media shall be designed. This will assure full serial data communication among all connected devices regardless of supplier. The goal of SAE J2602-2 is to improve the interoperability and interchangeability of LIN devices within a network by verifying the devices pass a minimum set of tests. To allow for easy cross-reference, this document is arranged such that the conformance test for a given section in SAE J2602-1 is in the same section in SAE J2602-2. This document is to be referenced by the particular vehicle Original Equipment Manufacturer (OEM) component technical specification that describes any given ECU in which the LIN data link controller and physical layer interface is located.
Standard

LIN Network for Vehicle Applications

2012-11-19
CURRENT
J2602/1_201211
This document covers the requirements for SAE implementations based on LIN 2.0. Requirements stated in this document will provide a minimum standard level of performance to which all compatible ECUs and media shall be designed. This will assure full serial data communication among all connected devices regardless of supplier. The goal of SAE J2602-1 is to improve the interoperability and interchangeability of LIN devices within a network by resolving those LIN 2.0 requirements that are ambiguous, conflicting, or optional. Moreover, SAE J2602-1 provides additional requirements that are not present in LIN 2.0 (e.g., fault tolerant operation, network topology, etc.). This document is to be referenced by the particular vehicle OEM component technical specification that describes any given ECU in which the single wire data link controller and physical layer interface is located. Primarily, the performance of the physical layer is specified in this document.
Standard

Class A Multiplexing Actuators

2001-08-30
HISTORICAL
J2057/2_200108
The Class A Task Force of the Vehicle Network for Multiplex and Data Communications Committee is publishing this SAE Information Report to provide insight into Class A Multiplexing. Multiplexed actuators are generally defined as devices which accept information from the multiplexed bus. A multiplexed actuator can be an output device controlled by the operator or an intelligent controller. A Multiplex actuator can also be a display device that reports the status of a monitored vehicle function. This document is intended to help the network system engineers and is meant to stimulate the design thought process. A list of multiplexed actuator examples is provided in Appendix A, Figure A1. Many other examples can be it identified.
Standard

Class B Data Communications Network Interface

2015-10-14
CURRENT
J1850_201510
This SAE Standard establishes the requirements for a Class B Data Communication Network Interface applicable to all On-and OffRoad Land-Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers. This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps (see Appendix A for a checklist of application-specific features). The Physical Layer parameters are specified as they would be detected on the network media, not within any particular module or integrated circuit implementation.
Standard

Class B Data Communications Network Interface

2006-06-07
HISTORICAL
J1850_200606
This SAE Standard establishes the requirements for a Class B Data Communication Network Interface applicable to all On- and Off-Road Land-Based Vehicles. It defines a minimum set of data communication requirements such that the resulting network is cost effective for simple applications and flexible enough to use in complex applications. Taken in total, the requirements contained in this document specify a data communications network that satisfies the needs of automotive manufacturers. This specification describes two specific implementations of the network, based on media/Physical Layer differences. One Physical Layer is optimized for a data rate of 10.4 Kbps while the other Physical Layer is optimized for a data rate of 41.6 Kbps (see Appendix A for a checklist of application-specific features). The Physical Layer parameters are specified as they would be detected on the network media, not within any particular module or integrated circuit implementation.
X