Search Results

This SAE Recommended Practice describes the implementation of Enhanced Diagnostic Test Modes, which are intended to supplement the legislated Diagnostic Test Modes defined in SAE J1979. Modes are defined for access to emission related test data beyond what is included in SAE J1979, and for non-emission related data. This document describes the data byte values for diagnostic messages transmitted between diagnostic test equipment, either on-vehicle or off-vehicle, and vehicle electronic control modules. No distinction is made between test modes for emission related and non-emission related diagnostics. These messages can be used with a diagnostic serial data link such as described in SAE J1850 or ISO 9141-2. For each test mode, this document includes a functional description of the test mode, request and report message data byte content, and an example if useful for clarification.

SAE J1978 defines the requirements of the OBD II scan tool. SAE J2201 defines the minimum requirements of the vehicle communications interface for the SAE J1978 OBD II scan tool. This interface connects the SAE J1962 test equipment connector to the hardware/software of the SAE J1978 OBD II scan tool that will use this interface to communicate with vehicles for the purpose of accessing required OBD II functions. Included in this SAE Recommended Practice are several definitions relating to the interface, and interface functionality evaluation. Appendix A - Examples include several example interface circuit implementations, which are believed to meet the requirements of this document and of SAE J1978. These examples are NOT requirements of this document. They are provided to assist circuit designers in developing interface circuits. Appendix B - Supporting Documents includes a list of supporting documents for the examples shown in Appendix A.

This SAE Recommended Practice defines the Expanded Diagnostic Protocol (EDP), the requirements for the SAE J1978 OBD II Scan Tool for supporting the EDP protocol, and associated requirements for diagnosis and service information to be provided by motor vehicle manufacturers. Appendix A includes worked examples of the use of the protocol.

This SAE Recommended Practice defines the Expanded Diagnostic Protocol (EDP), the requirements for the SAE J1978 OBD II Scan Tool for supporting the EDP protocol, and associated requirements for diagnosis and service information to be provided by motor vehicle manufacturers. Appendix A includes worked examples of the use of the protocol.

This SAE Recommended Practice recommends test methods, test procedures, and specific test parameters to help verify that vehicles and test tools can communicate using the SAE J1850. This document only verifies the portion of SAE J1850 that is used for OBD-II communications. The term “test tool” is synonymous with OBD-II Scan tool.

This SAE Recommended Practice recommends test methods, test procedures, and specific test parameters to help verify that vehicles and test tools can communicate using the SAE J1850. This document only verifies the portion of SAE J1850 that is used for OBD-II communications. The term “test tool” is synonymous with OBD-II Scan tool.

To define test cases for the OBD-II interface on external test equipment (such as an OBD-II Scan Tool, Inspection/Maintenance Tester, etc.) which can be used to verify compliance with the applicable standards such as SAE J1978 and SAE J1979 for Passenger Cars, Light-Duty Trucks, and Medium-Duty Vehicles and Engines (OBD II).

This SAE Recommended Practice recommends test methods, test procedures, and specific test parameters to help verify that vehicles and test tools can communicate using SAE J1962. These test procedures are to be used whenever SAE J1850 communication parameters need to be verified. However, all specific details for testing are not specified, e.g., sample size, environment, vibration, etc.

This SAE Information Report provides SAE’s recommendations for meeting the requirements for REAL NOx accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in OBD regulations 13 CCR 1971.1 and 13 CCR 1968.2.

This SAE Information Report provides SAE’s recommendations for meeting the requirements for REAL NOx accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in OBD regulations 13 CCR 1971.1 and 13 CCR 1968.2.

SAE J2534-1_0500 defines the pass-thru interface requirements for the reprogramming of emission related control modules. The SAE J2534-2/X_0500 document set adds extensions to the SAE J2534-1_0500 API (version 05.00) specification so that the API can be used for features not covered in the SAE J2534-1_0500 specification. Together, these features provide a comprehensive framework for a common standard, to protect the software investment of the vehicle OEMs and scan tool manufacturers. There is no required for an SAE J2534-2/X_0500 pass-thru interface to be fully compliant with SAE J2534-1_0500. SAE J2534-2/X_0500 interfaces can implement some or all of the features specified in the SAE J2534-2/X_0500 document set. This document must be used in conjunction with the SAE J2534-2/RE_0500 document.

SAE J1979-3 describes the communication between the zero emissions propulsion systems and test equipment required by government regulations. Standardization regulations require passenger cars and light-, medium-, and heavy-duty trucks to support a minimum set of diagnostic information to external (off-board) “generic” test equipment. To achieve this, SAE J1979-3 is based on the Open Systems Interconnection (OSI) Basic Refer to Model in accordance with ISO/IEC 7498-1 and ISO/IEC 10731, which structures communication systems into seven layers.

The purpose of this SAE Information Report is to specify the requirements necessary to fully define the Serial Data Communication Interface (SCI) used in the reprogramming of emission-related powertrain Electronic Control Units (ECU) in Fiat Chrysler Automobiles (FCA) vehicles. It is intended to satisfy new regulations proposed by the federal U.S. Environmental Protection Agency (EPA) and California Air Resource Board (CARB) regulatory agencies regarding “pass-thru programming” of all On-Board Diagnostic (OBD) compliant emission-related powertrain devices. These requirements are necessary to provide independent automotive service organizations and after-market scan tool suppliers the ability to reprogram emission-related powertrain ECUs for all manufacturers of automotive vehicles. Specifically, this document details the SCI physical layer and SCI data link layer requirements necessary to establish communications between a diagnostic tester and an ECU.

The purpose of this SAE Information Report is to specify the requirements necessary to fully define the Serial Data Communication Interface (SCI) used in the reprogramming of emission-related powertrain Electronic Control Units (ECU) in Fiat Chrysler Automobiles (FCA) vehicles. It is intended to satisfy new regulations proposed by the federal U.S. Environmental Protection Agency (EPA) and California Air Resource Board (CARB) regulatory agencies regarding “pass-thru programming” of all On-Board Diagnostic (OBD) compliant emission-related powertrain devices. These requirements are necessary to provide independent automotive service organizations and after-market scan tool suppliers the ability to reprogram emission-related powertrain ECUs for all manufacturers of automotive vehicles. Specifically, this document details the SCI physical layer and SCI data link layer requirements necessary to establish communications between a diagnostic tester and an ECU.

The purpose of this SAE Information Report is to specify the requirements necessary to fully define the Serial Data Communication Interface (SCI) used in the reprogramming of emission-related powertrain Electronic Control Units (ECU) in DaimlerChrysler Corporation (Chrysler Group) vehicles. It is intended to satisfy new regulations proposed by the federal U.S. Environmental Protection Agency (EPA) and California Air Resource Board (CARB) regulatory agencies regarding “pass-thru programming” of all On-Board Diagnostic (OBD) compliant emission-related powertrain devices. These requirements are necessary to provide independent automotive service organizations and after-market scan tool suppliers the ability to reprogram emission-related powertrain ECUs for all manufacturers of automotive vehicles. Specifically, this document details the SCI physical layer and SCI data link layer requirements necessary to establish communications between a diagnostic tester and an ECU.

To define a list of anomalies related to OBD Communications. Misinterpretations of various OBD Communications Standards and Recommended Practices have resulted in OBD “no-communications” situations in the field. This Information Report identifies the most prevalent of these.

This SAE Recommended Practice describes a standardized interface that connects between a standard personal computer (PC) and vehicle.The purpose of this interface is to enable the reprogramming of emission-related control modules, in 2004 and later model year vehicles. The interface shall consist of the necessary hardware and/or software to support the requirements defined in this document. It is expected that vehicle manufacturers will provide the software application that will control the pass-thru interface, to perform the actual reprogramming. The goal of this document is to ensure that reprogramming software from any vehicle manufacturer is compatible with interface supplied by any tool manufacturer. A common interface for all vehicle manufacturers reduces the tool costs for aftermarket garages, while allowing each vehicle manufacturer to control the programming sequence for the electronic control units (ECUs) in their vehicles.

This SAE Recommended Practice describes a standardized interface that connects between a standard personal computer (PC) and vehicle. The purpose of this interface is to enable the reprogramming of emission-related control modules, in 2004 and later model year vehicles. The interface shall consist of the necessary hardware and/or software to support the requirements defined in this document. It is expected that vehicle manufacturers will provide the software application that will control the pass-thru interface, to perform the actual reprogramming. The goal of this document is to ensure that reprogramming software from any vehicle manufacturer is compatible with interface supplied by any tool manufacturer. A common interface for all vehicle manufacturers reduces the tool costs for aftermarket garages, while allowing each vehicle manufacturer to control the programming sequence for the electronic control units (ECUs) in their vehicles.

The scope of the document is to define communication best practices in order to minimize problems for the vehicle owner when installing equipment which has a permanently or semi-permanently diagnostic communication device connected to the SAE J1962 connector or hardwired directly to the in-vehicle network.