Search Results

NVH quality is one of the most important criteria by which people judge the design of a vehicle. The Powertrain Mounting System (PMS), which can reduce the vibration from engine to vehicle cab as well as the inside noise, has attained significant attention. Much research has been done on the isolation method for three- and four-point mounting. But the six-point mounting system, which is usually equipped in commercial vehicle, is seldom studied and should be paid more attention. In this paper, the support rod installed on the upside of the transmission case is considered as a flexible body. Thus a rigid-flexible coupling model of PMS is established and the necessity of the established model is analyzed by comparing the simulation results of the new model and those of the conventional model.

The ride comfort of the commercial vehicle is mainly affected by several vibration isolation systems such as the primary suspension system, engine mounting system and the cab mounting system. A rigid-flexible coupling model for the truck was built and analyzed in multi-body environment (ADAMS). The method applying the excitation on the wheels center and the engine mountings in time domain was presented. The variables' effects on the ride performance were studied by design of experiment (DOE). The optimal design was obtained by the co-simulation of the ADAMS/View, iSIGHT and Matlab. It was found that the vertical root mean square (RMS) acceleration and frequency-weighted RMS acceleration on the seat track were reduced about 17% and 11% respectively at different speeds relative to baseline according to ISO 2631-1.

The optimization of vehicle suspension kinematic/compliance characteristics is of significant importance in the chassis development. Practical suspension system contains many uncertainties which may result from poorly known or variable parameters or from uncertain inputs. However, in most suspension optimization processes these uncertainties are not accounted for. This study explores the use of Chebyshev polynomials to model complex nonlinear suspension systems with interval uncertainties. In the suspension model, several kinematic and compliance characteristics are considered as objectives to be optimized. Suspension bushing characteristics are considered as design variables as well as uncertain parameters. A high-order response surface model using the zeros of Chebyshev polynomials as sampling points is established to approximate the suspension kinematic/compliance model.

Tyre behavior plays an important role in vehicle dynamics simulation. The Magic Formula Tyre Model is a semi-empirical tyre model which describes tyre behavior quite accurately in the handling simulation. The Magic Formula Tyre Model needs a set of parameters to describe the tyre properties; the determination of these parameters is nontrivial task due to its nonlinear nature and the presence of a large number of coefficients. In this paper, the homotopy algorithm is applied to the parameter identification of Magic Formula tyre model. A morphing parameter is introduced to correct the optimization process; as a result, the solution is directed converging to the global optimal solution, avoiding the local convergence. The method uses different continuation methods to globally optimize the parameters, which ensures that the prediction of the Magic Formula model can be very close to the test data at all stages of the optimization process.

The design of suspension affects the vehicle dynamics such as ride comfort and handling stability. Nonlinear characteristics and friction are important characteristics of suspension system, and the influence on vehicle dynamic performance cannot be ignored. Based on the seven-degree-of-freedom vehicle vibration nonlinear model with friction, the vibration response process of the vehicle and the influence of suspension friction on vehicle ride comfort and suspension action process were studied. The results show that friction will significantly affects the simulation of ride comfort and coincide with the function of the shock absorber. The suspension shock absorbers of vehicles were optimized with and without suspension friction. The results showed that the suspension tended to choose softer shock absorbers when there was friction. However, both of the two optimizations are able to improve the ride comfort of vehicles, and the simulation results were similar.

Elastomeric bushings are widely used in the passenger cars to make the cars have an ideal vehicle Noise, Vibration and Harshness (NVH) performance. However, elastomeric bushings also influence on the vehicle handling, ride and the durability performance of each component in the vehicle suspension system. It is relatively easy and cost effective to change the compliance of the bushing components compared with other method because they are made of elastomeric materials. The design of an elastomeric bushing is really a big challenge. One of the main difficulties comes from the different target compliance is wanted according to the handling, ride and durability demand at each different orientation (indicated by X Y Z) of the bushing. In this paper the following procedure was used for optimization of suspension elastomeric bushing compliance. Firstly, a detailed multi-body model was built including the nonlinear bushing effects and lower control arm flexibility.

This paper investigates a hierarchical optimization procedure for the optimum synthesis of a double-axle steering mechanism by considering the dynamic load of a vehicle which is seldom discussed in the previous literature. Firstly, a multi-body model of double-axle steering is presented by characterizing the detailed leaf spring effect. Accordingly, the influences of dynamic load including the motion interference of steering linkage resulted from the elastic deformation of leaf spring, and the effects of wheel slip angle and the position discrepancy of wheel speed rotation centers are explored systematically. And then, a hierarchical optimization method based on target cascading methodology is proposed to classify the design variables of double-axle steering mechanism into four levels. At last, a double-axle steering mechanism of a heavy-duty truck is utilized to demonstrate the validity of this method.

Active steering systems can help the driver to master critical driving situations. This paper presents a fuzzy logic control strategy on active steering vehicle based on a multi-body vehicle dynamic model. The multi-body vehicle dynamic model using ADAMS can accurately predict the dynamic performance of the vehicle. A new hybrid steering scheme including both active front steering (applying an additional front steering angle besides the driver input) and rear steering is presented to control both yaw velocity and sideslip angle. A set of fuzzy logic rules is designed for the active steering controller, and the fuzzy controller can adjust both sideslip angle and yaw velocity through the co-simulation between ADAMS and the Matlab fuzzy control unit with the optimized membership function. To ensure the design of high-quality fuzzy control rules, a rule optimization strategy is introduced.

A Special Analytical Target Cascading (SATC) process is developed for design problem which is difficult to ascertain the targets cascaded from upper level to lower level. The methodology is applied to achieve improving Handling Performance and Ride Quality (HPRQ) of a passenger car. A bi-level hierarchical structure with target-transforming process is established based on conceptual suspension model and multi-body models. DOE, RSM and a combined optimization method of simulated annealing and Programming Quadratic Line search is applied to execute the optimization process. The result shows that HPRQ is improved through special ATC based on CSM and multi-body modeling technique.

To design and optimize the vehicle driveline is necessary to decrease the fuel consumption and improve dynamic performance. This paper describes a methodology to optimize the driveline design including the axle ratio, transmission shift points and transmission shift ratios considering uncertainty. A new and flexible tool for modeling multi-domain systems, Modelica, is used to carry out the modeling and analysis of a vehicle, and the multi-domain model is developed to determine the optimum design in terms of fuel economy, with determinability. Secondly, a robust optimization is carried out to find the optimum design considering uncertainty. The results indicate that the fuel economy and dynamic performance are improved greatly.

To provide a greater weight capacity, the tandem axle which is a group of two or more axles situated close together has been used on most heavy truck. In general, the reaction moments during braking cause a change in load distribution among both axles of the tandem suspension. Since load transfer among axles of a tandem suspension can lead to premature wheel lockup, tandem-axle geometry and the brake force distribution among individual axles of a tandem suspension have a pronounced effect on braking efficiency. The braking efficiency has directly influence on the vehicle brake distance and vehicle travelling direction stability in any road condition, so how to improve the braking efficiency is researched in this paper. The load transfer among individual axles is not only determined by vehicle deceleration but also by the actual brake force of each axle for tandem axle suspension, which increases the difficulty of braking efficiency improving.

As is known to all, there are some contradictions between the handling and ride performance during the design process of vehicles. Sometimes owing to serious collisions of each criterion in the high-dimensional solution space, the common method to deal with the contradiction is to transform into a single target according to weights of each objective, which may not obtain a desired result. A multi-criteria approach is therefore adopted to optimize both properties and the result of a multi-criteria design is not a unique one but a series of balanced solutions. This paper is focused on the robust design of a simplified vehicle model in terms of not only ride comfort but also handling and stability using a multi-objective evolutionary algorithm (MOEA) method. Using the proposed method, the conflicting performance requirements can be better traded off. One of the most important indexes to characterize the vertical ride comfort is the acceleration of the sprung mass.

In order to reasonably match the variable stiffness and location of the Powertrain Mounting System (PMS) and optimize the ride comfort of commercial vehicle, a thirteen degrees of freedom (DOF) model of a commercial vehicle was established in Adams/view. Specially, the support rod installed on the upside of the transmission case was modeled as a flexible body. The vibration isolation provided by the PMS was evaluated in three aspects: the energy decoupling of the powertrain, the response force of the mount and the displacement of the powertrain. The energy decoupling ratio, the force RMS of the mount when force excitation was applied on the powertrain and the displacement of the powertrain Center of Gravity (C.G) when displacement excitation was applied on the vehicle chassis were selected as the optimal target. Adams and MATLAB were integrated into the optimization software iSIGHT to optimize the PMS. NSGA-II is used to obtain some Pareto-optimal solutions of PMS.

Interval inverse problems can be defined as problems to estimate input through given output, where the input and output are interval numbers. Many problems in engineering can be formulated as inverse problems like vehicle suspension design. Interval metrics, instead of deterministic metrics, are used for the suspension design of a vehicle vibration model with five degrees of freedom. The vibration properties of a vehicle vibration model are described by reasonable intervals and the suspension interval parameters are to be solved. A new interval inverse analysis method, which is a combination of Chebyshev inclusion function and optimization algorithm such as multi-island genetic algorithm, is presented and used for the suspension design of a vehicle vibration model with six conflicting objective functions. The interval design of suspension using such an interval inverse analysis method is shown and validated, and some useful conclusions are reached.

When the drill arm reaches the specified position, the rubber top disk of the propelling beam is pressed against the rock surface by the hydraulic cylinder force and the rock drill starts drilling. Because of the reaction force and the deformation of the drill arm, the propelling beam will be offset from its target position and vibrate, which will affect the drilling accuracy. To analyze the vibration of the propelling beam, the rigid-flexible coupled model is established. The minimum displacement offset of the propelling beam from the initial position is used as the optimization function and the parameters of the rubber top disk are used as optimization variables. The amplitude of the propelling beam at a steady state is used as the constraint. From the simulation results, the rigid-flexible coupled model can describe the vibration of the propelling beam better than the rigid model, especially during the rock drill working stage.

Unsuitable shift control strategies may increase the vehicle jerk and clutch wear. In order to improve the shift quality of electric vehicles (EVs) equipped with dual clutch transmission, this paper proposes an optimal shift control strategy based on linear quadratic regulator, in which weighting matrices are selected by using genetic algorithm (GA). The dynamics of the shift process of the dual clutch transmission is analyzed to establish the dynamic model of the driving system. In addition to the vehicle jerk, the friction work of clutch is also considered as one of the performance criteria and a new linear quadratic objective function is formulated. The optimal weighting matrices for obtaining a globally optimal solution are selected benefit from the global search capacity of genetic algorithm. The optimal target trajectories of the torque of the two clutches and motor are obtained by simulating the linear quadratic regulator (LQR).