Search Results

The objective of this study is to characterize the operation of an air-assisted fuel injector. This characterization involves four sets of tests: fuel and air flow calibration; instantaneous measurements of fuel and air solenoid signals, internal pressure in the injector, and poppet lift; photographs of the spray; and droplet sizing. The injector poppet was designed to form a spray of 80° included angle. Nitrogen, instead of air, was used to assist the injection of unleaded gasoline into steady, compressed nitrogen at room temperature. The following conditions were used: nominal fuel flow rates of 10, 20, and 30 mm3/injection; spray chamber pressures of 0.1, 0.169, and 0.445 MPa; and nominal injections per minute (IPM) of 1600 and 3000. Results showed a linear increase in total fuel mass supplied to the injector as fuel solenoid pulse width was increased, except at the highest IPM and chamber pressure when the total fuel mass tended to level off.

Results of experiments performed on a direct-injection two-stroke engine using an air-assisted injector are presented. Pressure measurements in both the engine cylinder and injector body coupled with backlit photographs of the spray provide a qualitative understanding of the spray dynamics from the oscillating poppet system. The temporal evolution of the spatial distribution of both liquid and vapor fuel were measured within the cylinder using the Exciplex technique with a new dopant which is suitable for tracing gasoline. However, a temperature dependence of the vapor phase fluorescence was found that limits the direct quantitative interpretation of the images. Investigation of a number of realizations of the vapor field at a time typical of ignition for a stratified-charge engine shows a high degree of cycle to cycle variability with some cycles exhibiting a high level of charge stratification.

Efforts are reported to reproduce the distribution of liquid and vapor fuel from a pulsating hollow-cone liquid-only injector measured by the planar exciplex technique within the head cup of a motored ported single-cylinder engine operated at 1600 rpm with high swirl and a squish ratio of 75%. The injector, cup and cylinder were coaxial. The measurements show that shortly after the beginning of the injection the maximum liquid and vapor fuel concentrations are along the axis but also that the spray achieves substantial radial and axial penetrations. The engine flowfield without injection had previously been characterized by LDV and PIV and so had been the injector and its spray in constant pressure environments so that little arbitrariness was left in reproducing the spray in the engine. Two spray models were used. In one the large drops produced by the break up of the liquid sheet were introduced into the numerical field at the injector exit nearly with the poppet seat angle.

A second effort is reported to reproduce the distribution of fuel from a pulsating hollow-cone liquid-only poppet injector measured by the planar exciplex technique within the head cup of a motored ported single-cylinder engine operated at 1600 rpm with high swirl and a squish ratio of 75%. The injector, cup and cylinder were coaxial. The engine flowfield without injection had previously been characterized by LDV and PIV and so had been the injector and its spray in constant pressure environments. In a previous effort, the injector was assume to generate drop and the computed collapse of the spray was found to be too slow. In this work, the injector is assumed to generate liquid sheets that change shape and produce drops from their leading edges and surfaces as they propagate through the gas.

Simultaneous fuel distribution images (by shadowgraph and laser-induced fluorescence) and cylinder pressure measurements are reported for a combusting stratified-charge engine with a square cup in the head at 800 RPM and light load for two spark locations with and without swirl. Air-assisted direct-injection occurred from 130°-150° after bottom dead center (ABDC) and ignition was at 148° ABDC. The engine is ported and injection and combustion take place every 6th cycle. The complicated interaction of the squish, fuel/air jet, square cup, spark plug geometry and weak tumble gives rise to a weak crossflow toward the intake side of the engine with no swirl, but toward the exhaust side in the presence of strong swirl, skewing the spray slightly to that side.

Planar instantaneous fuel concentration measurements were made by laser-induced fluorescence of 3-pentanone in the spark gap just prior to ignition in a direct-injection spark-ignition engine operating at a light load, highly stratified condition. The distribution of the average equivalence ratio in a circle of 1.9 mm diameter centered on the spark plug showed that a large fraction of the cycles had an equivalence ratio below the lean limit, yet acceptable combustion was achieved in those cycles. Further, weak correlation was found between the local average equivalence ratio near the spark plug and the time required to achieved a 100 kPa pressure rise above the motoring pressure, as well as other parameters which characterize the early stages of combustion. The cause for this behavior is assessed to be mixture motion during the spark discharge which continually convects fresh mixture through the spark gap during breakdown.

The combustion chamber pressure computed with a three-dimensional model is compared with the measured one in a rotary engine fueled with mixtures of natural gas and air. The rotary engine has a rotor displacement of 654 cm3, a compression ratio of 9.4 and uses 2 ignition sparks. The model incorporates a k-ϵ submodel for turbulence, wall function submodels for turbulent wall boundary layer transport, and a hybrid laminar/mixing controlled submodel for species conversion and energy release. Nine cases are considered that cover a wide range of engine operating conditions: rpm of 2503-5798, volumetric efficiency of 35.7-100.5% and equivalence ratio of 0.59-1.15. In all cases the computed and measured pressures agree within 12%.