Protection of surfaces is a critical factor in determining the extended service life of a structure in polluted and aggressive environments. In particular, a rapid growth of the technology for the protecting coating of cold rolled steel is experienced, for the use in transport, electric housewares, building and industrial plants. Numerous changes have taken place in the production of zinc coatings on steel in order to improve the corrosion resistance using zinc alloy platings. Our research group collected from the international production a number of selected galvanized steel samples, including electrodeposited zinc alloys, multilayer coatings, hot dip galvanized steels. On the selected materials we established and analyzed morphology, composition, crystal structure, impurity content and distribution, using many surface microanalysis techniques.
The socio-economic system is coming to the conclusion that the environment will no longer tolerate and absorb all of man's interventions, and that natural resources no longer constitute a cheap and inexhaustible source of wealth. In this scenario of the limits of nature and ever-increasing environmental costs, we are faced with the problem of recovering and reusing the materials which go into the manufacture of an automobile. The replacement of metal materials with polymer materials leads to a reduction in the re-usable waste, and to an increase in the amount of waste with no economic value, or even with a negative economic value. The use of the non-ferrous and non-aluminous materials in an automobile is beyond the capabilities of new techniques for scrapping automobiles, which means that at the end of their lives, the automobiles must be disassembled, sorted on the basis of the constitute materials, recovered and recycled.
Shape memory materials undergo temperature-induced martensitic phase transformations that involve reversible dimensional changes. In performing these changes in shape, the shape-memory material is able to do work against external constraints, and this is the basis for shape-memory low-temperature heat engines. The transformation temperatures on heating and cooling are often not very different (little hysteresis) and are well defined and reproducible. Furthermore, these temperatures can be adjusted by varying the composition of the shape memory alloy. Internal combustion engines dissipate approximately two-thirds of the fuel energy as heat to the exhaust and coolant systems. A low-temperature heat engine could convert a fraction of this heat energy to useful work. This paper discusses the conceptual basis for the application of shape memory heat engines to internal combustion engine powered vehicles. Metallurgical and thermodynamic factors are discussed, as well as engine efficiency.
The paper describes recent developments in the use of stainless steel to make the parts of buses which are most liable to corrosion. Sheet metal is used for the outer panelling, and square and rectangular tubes for the body. The types of steel used and their fabrication are analyzed. Finally, a brief description is given of the stainless steels used to make car exhaust systems.
Mold designers and foundrymen spend a lot of time in developing molds without knowing exactly the phenomena which take place inside. Simulor, which has been used in an industrial environment for two years, offers the solution to make foundrymen understand what happens during the filling of the mold and the solidification of the part. Based on navier-stokes and heat transfer equations, simulor provides speed distribution and metal front evolution in the cavity and thermal map in the mold and the part. Some examples with different metals (cast iron, aluminum alloy) cast with various processes (sand or die casting, low pressure or gravity casting) will be given. This new tool will given foundrymen the opportunity to test the mold before having it machined and will also allow reduction in development delays.
Particulate reinforced aluminum composite is described and properties shown. Application of this material to specific components are discussed, and it is shown that significant progress has been achieved on the road to commercial automotive introduction.
In order to improve the design of drawn parts and to reduce the number of trial and error tests, Renault has undertaken the development and the validation of various finite element procedures and codes. This paper describes the function of each software and its level of integration into the design process. One of them is already an operational tool used be planners whilst the others are still in the validation phase. Selected examples show typical applications of the computer programs on automotive parts.
Indirect squeeze casting technology is one of the most attractive fabrication techniques of near net shape components constituted by aluminum matrix composite (AMC) materials. AMCs reinforced with both continuous and discontinuous ceramic elements have been mainly produced by infiltration of porous preforms. Nevertheless, a further promising production route offered by this technique is given by the possibility to employ ingots of pre-reinforced aluminum alloys containing ceramic particles (silicon carbide or alumina); ingots are remelted and, under suitable operative conditions, high quality composite castings of simple and complex shape are produced by squeeze casting. The present paper describes the results of an extensive experimental work carried out by Alures-Centro Tecnico Porcessi on a pilot plant scale employing a vertical squeeze casting machine with a clamping force of 315 tons.
In this paper the socio-economic and technical problems of the handling of car wrecks are discussed. The recovery of metals as a goal for shredder operations will increasingly be supplemented with the recovery of other materials such as polymers. In order to deal economically and technically with polymer materials, it is necessary to know in advance which type of wreck handling will be used. Also optimization of shredder operations allow less freedom to incorporate a variety of materials when compared with selective dismantling or disassemble of cars. It is argued that various technical solutions have to be accompanied by increased cooperation along the firms that are connected to the handling of car wrecks. Cooperation between the scrap context and designers is essential, in order to optimize dismantling practices according to criteria of environmentally preferred solutions.
The purely theoretical evaluation of critical compression loads seems complex and not very reliable in the case of honeycomb panels, on account of the numerous parameters in play and their complex interrelationships. This report provides the designer with a fast tool for preliminary calculations, consisting of a finite-element mathematical model with elastic-linear code (which can be processed using a PC), which makes it possible to obtain information very closely resembling the real situation.
A perspective microarc oxidization (MAO) technology used for the obtention of ceramic coatings is described. The coat formation mechanism and its phase composition and revealed conformably to aluminum alloys. The results of the analysis of MAO-coatings are given by their cohesive strength with respect to the substrate and microhardness distribution within ceramic layer thickness. The examples of practical use of coatings are given and possible perspectives of MAO-technology inculcation are outlined.
Semi-liquid forming process, applied to pressure die-casting, permits to obtain low cost components with high qualitative characteristics and adequate mechanical performances. The technology is based on the employment of material with globular microstructure (flow-cast alloys) obtained subjecting a metal alloy at the time of solidification to an elevated shear rate. Such microstructure permits the accomplishment of conventional forming processes at temperatures in solidification range. The particular fluid-dynamic properties of the semi-liquid slurry and the lower injection temperature allow to obtain casting with improved soundness, without need of impregnation, and to extend die life. The present work describes the Weber (Magneti Marelli) activity of the process industrialization and some applications for the manufacture of automotive components.
The paper review some recent efforts, made by the aluminum industry, towards the development of new advanced alloys for aerospace applications; unconventional production technologies and MMC occupy an outstanding position in this context. Raid solidification processes are currently used for obtaining advanced alloys and, among them, the powder metallurgy route is one of the most commonly applied, since it has reached a considerable level of maturity. Experimental results of PM materials are shown and discussed in order to appreciate the potentialities of this class of materials and some recent further progress is shown: the spray deposition approach (osprey process). After having described the main features of the osprey process, some results obtained at the Department of Aerospace Engineering of Pisa about the development of high strength Al-alloy and MMC obtained by means of the osprey process are shown.
The following paper describes the experimental activity regarding the setting-up and characterization of a car engine bracket in Al-Si12Cu2FeZn-F alloy produced by the new technology squeeze casting. LExperimentation was carried out at the Alures squeeze casting pilot plant. Static and dynamic characterization (fatigue resistance on test samples and the component itself) was carried out at Teksid and Fiat Auto. Characterization test have demonstrated the considerable advantages offered by the new technology compared with conventional production processes.