Refine Your Search

Topic

Author

Search Results

Standard

J826/3 CAD Model of Legs and Back Hardware for SAE J826 3-D H-Point Machine

2014-10-16
WIP
J826/3
This document describes the CAD model data of legs and back hardware available from SAE for the HPM-1 three-dimensional H-point machine. The elements of the CAD model include the feet, lower and thighs as well as headroom probe and t-bar. Also included are datum points and lines, and calibration references. The intended purpose for this information is to provide a CAD reference for design and benchmarking as well as a calibration reference for the physical HPM-1 audits. The content and format of the data files that are available are also described. The actual CAD model files are included with this product and are provided in the following formats: CATIA v4 (without parametrics), CATIA v5 (without parametrics), IGES, and STEP.
Standard

Information Report for Hoists used with an Unoccupied Mobility Device

2010-02-02
WIP
J2930
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility and performance of automotive hoists designed to load and unload an unoccupied Mobility Device into or upon a personally licensed vehicle.
Standard

In-line, Elbow, and Tee Flanged Connectors for use with SAE J518-1/ISO6162-1 Components

2015-02-03
WIP
J518/4
This document standardizes the design of connector blocks used for joining SAE J518-1/ISO 6162-1 (Code 61) flange heads with other SAE J518-1/ISO 6162-1 (Code 61) flange heads with straight, elbow, and tee geometries. The blocks specified in this document are designed to provide for very compact installations. As a result, the tap depths specified in this document do not conform to those specified in SAE J518-1/ISO 6162-1 to allow for a minimal bend radius in the elbow and tee configurations. This document specifies both inch and metric configurations
Standard

Round Head Bolts

1990-01-01
CURRENT
J481_199001
Round head bolts are made in two body styles: (a) A full size body, with a maximum diameter somewhat greater than the nominal diameter (not an SAE Standard except for ribbed neck bolts, Table 3); and (b) an undersize body, with a minimum diameter approximating the pitch diameter of the thread and a maximum diameter never exceeding nominal (SAE standard for all types except ribbed neck bolts). The body diameter of either style may be exceeded by a reasonable swelling or fin under the head, or under corners of the square necks, to the extent that serviceability is not affected.
Standard

Cotter Pins

1990-01-01
CURRENT
J487_199001
Not available.
Standard

Alignment of Nut Slots

1990-01-01
CURRENT
J484_199001
This method of gaging alignment of nut slots allows equal variations for location of the cotter pin hole in the bolt and location of slots in the nut. To inspect the nut, the slotted gage is inserted through the nut hole from the bearing surface of the nut. Alignment of slots is considered satisfactory if the gage pin can be slipped into the gage and nut slots without interference.
Standard

Minimum Performance & Compatibility Criteria for MVAC Flushing Fluids used in R-134a & R-1234yf Systems.

2015-02-16
WIP
J3091
This SAE standard applies to any and all Flushing Fluids intended for aftermarket use to clean and decontaminate sections of the refrigerant circuit within a vehicle A/C system. This standard provided testing and acceptance criteria for determining minimum performance and compatibility of Flushing Fluids with A/C system materials and components, which may be intended for use in servicing vehicle A/C systems. This standard will only indicate a Flushing Fluid's minimum performance criteria, and that it is chemically compatible with materials used in the A/C system. It is not the intent of this document to identify requirements for ultraviolet leaks detection dyes, as such dyes must meet the requirements of SAE J 2297. It is not the intention of this document to identify requirements for system additives, as such additives must meet the requirements of SAE J 2670.
X